# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
After being told it would cost around $1300 to install a trailer hitch I figured I would just rent a truck if I needed to pull a trailer. When I saw your ad I was in but was concerned that it would be too complicated to install myself. I turned out to be super simple including the electrical wiring. I'm recovering from a knee joint replacement so was concerned I couldn't get where I needed to be to get the job done but it was a breeze. Everything works beautifully and is solid as a rock. Thanks for such an exceptional DIY product. Now if you have a hitch for my other car, a 1962 Willys Utility Wagon. I'd like one.
My tow hitch and wiring harness arrived on time and was really easy to install. Half the price of having someone install it, and it looks great.
# 2
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
Perfect fit, Great quality, Incredibly fast shipping! Overall completely satisfied without a single complaint or issue. Now time to buy a boat!
This wiring harness did not have enough wire on it for my 2011 Jeep Grand Cherokee. I had to make numerous splices to get the harness to work.
# 3
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Excellent quality. Very heavy duty. The mounting flange is 3/4" thick. Just FYI: The 4 inch drop is measured from the top of the square mounting tube to the top of the ball mounting flange. When installed inverted, the 2 3/4 inch rise is measured from the top of the square mounting tube to the top of the ball mounting flange. (Note that the "top of the square mounting tube" varies when you invert the mount for rise versus drop.)
Everything arrived on time as usual from etrailer.
# 4
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Good ball mount. Meets my requirements for proper trailer alignment.
# 5
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Simple and it works.
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
# 6
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
The super extra long ball mount is perfect, gives the extra distance between tow vehicle and trailer because without the extra long mount there is only 32" between vehicle and trailer wall. A friend borrowed this trailer and when he backed up the trailer hit the rear tail light and crushed the corner of his truck. With the extra long mount at least the trailer corner wall will clear if this ever happens again. Also great if you have a rear mounted spare tire
This makes an EXCELLENT knee knocker and pulls a trailer even better. Really stands out from the back of the Grand Cherokee which is exactly what I wanted.
# 7
Curt Class III Ball Mount with 2" Ball - 4" Drop - 2" Rise - 7,500 lbs
I haven't been able to use yet, however the only draw back was that I was under the impression that the pin came with it. It was my mistake because I didn't read the description fully. Can't wait to get to use.
# 8
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
It is the right size for 2016 Jeep Grand Cherokee. Gives 3-4" clearance from bumper to ball. And 19" height to top of steel bar and 22" to top of ball.
I haven't been able to use yet, however the only draw back was that I was under the impression that the pin came with it. It was my mistake because I didn't read the description fully. Can't wait to get to use.
# 9
Curt Towing Starter Kit for 2" Hitches - 2" Ball - 2" Rise, 4" Drop - 7.5K
Nice combination to go with my front hitch for the F150.
# 10
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Thank you, thank you - product is made in AMERICA !!!!! No Chinese junk.
Wow, sturdy is what I can say! Nice drop at 2". I have a Grand Cherokee with the air suspension, so I can adjust to what I need.
# 11
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
The ball mount was a complete failure even after a lengthy discussion on the phone. I wanted a ball mount that would accept the rocker ball and anti-sway bar. The bar sent to me can't be used this way. An email and phone message to the sales person I ordered with, got no response.
# 12
MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 7-1/2" Drop, 6-1/4" Rise - 5,000 lb
As advertised and quick delivery, I am an Etrailer fan!
Strong and works perfectly!
# 13
Curt Class III Ball Mount with 2-5/16" Ball - 2" Drop - 7,500 lbs
I haven't been able to use yet, however the only draw back was that I was under the impression that the pin came with it. It was my mistake because I didn't read the description fully. Can't wait to get to use.
Perfect fit, Great quality, Incredibly fast shipping! Overall completely satisfied without a single complaint or issue. Now time to buy a boat!
# 14
Curt Class III Ball Mount with 1-7/8" Ball - 2" Drop - 3,500 lbs
I haven't been able to use yet, however the only draw back was that I was under the impression that the pin came with it. It was my mistake because I didn't read the description fully. Can't wait to get to use.
Perfect fit, Great quality, Incredibly fast shipping! Overall completely satisfied without a single complaint or issue. Now time to buy a boat!
# 15
Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount - 7" Rise to 9-1/2" Drop - 5,000 lbs
Thank you, thank you - product is made in AMERICA !!!!! No Chinese junk.
Wow, sturdy is what I can say! Nice drop at 2". I have a Grand Cherokee with the air suspension, so I can adjust to what I need.
What our customers are saying:
"Very broad selection and outstanding service."