Most Popular Aero Bars for 2009 Honda Civic

The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.

Click to Enlarge

Loved the racks, seem very durable. Only downside was that the groove made for the crossbeam was quite a bit smaller than my crossbeams, but they still secured down great. You'd have to have a pretty funky set-up for these racks to not work on your vehicle. Having all the straps/tie-downs included was awesome too. Reccomend!

Click to Enlarge

The product seems great but I have not figured out how to get it safely attached to my bars. I have an Agricover Adarac on the bed of my truck and the crossbars are 1-1/2 x 1-1/2 inches square. I thought this would work well since it's for up to 3-1/2 x 1-11/16" crossbars, but it isn't secure on these. I'm going to try and figure out an alternate method for attachment though. Thule Hull-a-port Pro's are the perfect (mounting) solution but don't seem to be made any longer.

Click to Enlarge

Great product and great customer service! Very easy to install, but I highly recommend to watch the installation video first. We used typical black office clips to clip the excess straps down since they came untangled when driving. Also, I recommend to purchase locks for the racks since we are concerned someone may steal them because they are so easy to take on and off.

Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.

Click to Enlarge

I think the Thule Hulaport kayak racks are the best, most secure way to transport your kayaks. I had these on my Xterra and hauled two kayaks up to Cape Bretton park in Nova Scotia, Canada from Connecticut, USA no problem. We were even able to store gear in the kayaks for the trip. I’m so excited to have them for my Crosstrek. Highly recommend these!

Click to Enlarge

Works great. I’m 5’6” and the pivoting cradles make for easy loading and off loading. I do need a stepping stool to install the carrier on the roof rack.

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

Click to Enlarge

We needed a better way to haul around 3 kayaks and after looking at a number of options, we settled on the Thule Stacker setup. Installation is simple and the stackers provide a sturdy option for hauling multiple kayaks. One of the best features is that they fold down when you don't need to use them. My shopping experience with etrailer was smooth and shipping was prompt.

Click to Enlarge

My wife uses these to carry two small kayaks in the roof of her Subaru. They work great and we very happy with the purchase. She also likes finding her car easier in the parking lots, even with the carriers folded down.

Click to Enlarge

Works perfectly. I didn't feel like spending a lot of money on a roof rack at this point in my life so this fits the bill. The roof on my Honda is a little weak so it buckles when I go over big bumps, just take it slow.

It's doing the job of securing my kayak to my rackless prius, at a fraction of the cost. However, the instructions included along with the straps did not work for me. I spent a considerable amount of time adjusting things: the red straps that are supposed to go over the boat and secure on the bars were not long enough. The blue straps are much longer, so I am using the red straps to secure the bars to the car, through the open doors and cinched inside the car. I am using the blue straps to reach over the boat, and I decided to feed those into the car too- feels more secure than to attach them to the bars on top. The black straps for front and back strapping don't work for my car in the way shown, I had to jerry-rig. Overall I have figured out how to make it work, and I'm glad I didn't spend $xxx.xx on a serious rack system.

Click to Enlarge

Carry my SUP on my Honda Civic with this on a Thule carrier bars. Has held up well after a year in the sun in Southern California.

I love this rack! I don't think I'll ever take it off my car. Cool and functional. I've used it for my snowboard in the winter and my surfboard and camping gear in the summer.

Click to Enlarge

Very easy to install on roof rack. Just be careful not to lose one of the rubber pieces that help protect your board. They can easily fall off of the rope when tying your board to the rack.

With a little help from youtube, this was one of the easiest things I've ever assembled! LOVE my new SUP rack!!

Click to Enlarge

The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.

Click to Enlarge

Click to Enlarge

This product was very easy to install. I had it installed in about 15 minutes and my kayak on the roof a few minutes later. The only issue I had was one of the tie-down straps was broken (stitching was not complete or something). Other than that, this product was great! The customer service (Carol and Neil) were great also, helping with the strap problem. Thank you again!

Click to Enlarge

Click to Enlarge

I acquired a second kayak and needed a system to fit the factory racks on my 2011 Toyota RAV4. Etrailer.com has always had information on what fits and has always had the item needed for the job. I attached the Yakima BigStack to the top with ease, and, with one other person to hold the kayaks while I secured, tied two of them down for a long road trip to Northern Minnesota. The system worked just fine. The only caveat was in the configuration of multiple boats in the instructions. The diagram has two boats on the same side of the posts, however, I found it more secure to put one on either side ( other reviews of this product on different Internet sites have found similar results.) The boats made it through the trip with no shifting.

Worked great on our Subaru Crosstrek with factory crossbars. Loading very easy, and it was very secure, for our 2 kayaks. The Yakima Big Sticks are easy to install/setup and take off. Very happy with our investment,

These work great and I was able to install them on the OEM rack for my truck. The only downside is that the threads for the clamp hang down a little too close to the roof for comfort.

The Rhino-Rack 2 Kayak Carrier I ordered from etrailer was easily reviewed and ordered from their website and ALL communication relative to order confirmation and extreme detail included in their tracking was nothing short of phenomenal! The items were packaged with care and arrived intact. These fit our basic Lexus crossbars and is the perfect product for carrying our two (2) kayaks. My hat goes off to the great folks at etrailer -- It doesn't get any better than this!!!

Product was as advertised, however it was missing four bolts that I had to get at a hardware store, but other than that it was fine. Service from etrailer team was outstanding.

I've been using the product for two summers now and it is perfect for what I'm using it for. My canoe is an Old Town Discovery 133, it's very wide and I initially had trouble fitting it in the brackets with how relatively narrow my Rav4 is, but the instructions that came with them mentioned I could just flip them around. That worked perfectly. I only use the brackets and the tie down straps from the kit to tie the boat to the crossbars, and then use the painter lines I put on the bow and stern of the boat to tie those to the car. That rides on the highway very easily with no shifting. With two people, the load/unload time is around 10 minutes as long as one person knows what they are doing. This kit had exactly what I was looking for, seems built to last, and if I ever need another kit to help tie a canoe to a car then I know I can trust this product to get the job done safely and reliably.

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

Click to Enlarge

Click to Enlarge

The Hullivator was for my wife to give her the option of loading and unloading by herself. It couldn’t be better. She now goes kayaking anytime she wants with little effort and no need for me to help her. Excellent product that’s worth every cent. Was super easy to install too.

Click to Enlarge

Excellent product, easy install, secure on the crossbars, a bit lower ride height and a simple rolling mechanism. A significant improvement over my older Yakima Handroll racks.

The Sweet Roll will not support my Old Town Topwater 10.6. The brackets spread out on the crossbar under the weight. This year I will try a Yakima Big Catch. The Sweet Roll works fine with our Old Town Loons.

These work great! They fit well with my Brightlines Aero Rack where others did not. Super Good quality and super easy to install, I was surprised on the quality. I gave it 4 Stars because they sort of shift to the side if I put alot of pressure, however once the weight of the kayaks get on it, I don’t think it will be any problem.

Click to Enlarge

quick and easy installation. shipping was faster than quoted. pleasure doing business with.

Easily adjustable. Very happy with them after 1 year. I carry 10ft and a 12ft kayaks.

Click to Enlarge

These are great. I had trouble finding a system I really liked but then on a trip one of our friends had these and loved them. They are simple, secure and low profile. I use them with 18’ sea kayaks. The pads flex to fit the hulls just right, the boats are super secure, no wondering around and you don’t have to strangle them into the saddles. I was worried maybe the boats wouldn’t slide easily onto them when loading but it’s no problem. One note, the slugs were just a shade too big to fit in my older TracRac slot. It took just a little work with the grinder, no big deal. Very happy.

I received the rollers and locks yesterday, mounted today and loaded my kayak. All-in-all, the rollers work pretty well but but I do think that the rollers are over-priced for what you get. So, I knocked off a star.

The Yakima roller make it easier to load and secure a kayak to the roof of a 4Runner. The fit is secure enough that I don't need to use bow & stern straps for shorter trips.

Installation was pretty easy. Racks seem solid. Looking forward to get to use them.

These pads worked well on our Yakima RailBar Crossbars- Item #Y00448-0449 that we also bought from etrailer around 2020/2021. Not sure if etrailer carries the exact Yakima Crossbars anymore, but think they have a similar model. Both the pads and crossbars work well to haul our kayak on our 2019 Subaru Forester. etrailer's customer service rocks! We had a lot of questions purchasing both items and they were great to talk to!

Click to Enlarge

Click to Enlarge

Click to Enlarge

Brought home a new kayak yesterday using this J cradle for the first time. Easy to set up and load. Two complaints: not impressed with the strap buckles - had to tie knots to secure. And the 3-inch bolts weren’t long enough to easily attach the cradle to my Rhino Rack crossbars, so I had to replace them. Also got my finger pinched pretty good adjusting the cradle knobs - my fault for not being more careful, but just saying …

Click to Enlarge

Great product for the price - The cradles were very easy to mount (and lay flat once folded). The videos were helpful in showing how to set the straps in the most efficient way. I test-drove my car today with my fishing kayak on top on a 80-mile round trip (a mix of freeway, country road and dirt tracks). The kayak was perfectly still, no particular wind noise and I was able to muscle to kayak up the roof and take it down on my own (it's a 52 lbs boat). I really recommend that product and I'm glad I went for J-Style cradles!

Click to Enlarge