# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2002 Chevrolet SilveradoThe hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.
A solid hitch and super easy install. With the factory tow hooks, the install only required a 18mm socket and some of the hardware provided on my 2002 Chevrolet Silverado 2500 HD ext cab.
# 2
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I have an 08 duramax and it fit perfectly. The cutting on the front plastic was very minimal and easy. The video installation video was a great help.
This worked good on my 09 Chevy 3500HD. Since I have a truck camper, I carry our bikes on the front of the truck. The only down side of this is that the pin is behind the air dam. So you have to lie down under the truck to put the pin in.
# 3
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Ordered front receiver from etrailer and received producy very quickly . I will be using receiver for surf fishing rack. I would recommend having a helper for installation. This receiver from drawtite # 65078 fit my 2019 Silverado 2500 perfectly
etrailer very informative ,product - hitch as described ..install was easy ,took me a little longer as i was on my back ,i am 65 years old and went in per their instructions..i am satisfied ,i would recommend this 65078 hitch from etrailer ... 2019 3500HD LTZ Silverado is what i installed it on.
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Ordered the same hitch from Amazon, and showed up not J-Pin ready, with (1) hole drilled for a hitch pin against the weld. Can't run the nut flush because of the interference with the weld bead, and no 7/16" hole present. Returned it. Ordered another one from etrailer direct. Called in the order to make sure they QC'd prior to shipping. Assured me they would. Box never opened, and the same nonsense showed up. Not happy, trying to work it out.
Fit Perfectly, super easy to install, and super fast shipping! Holds Hollywood Bike Rack Great and very solid for my two E-bikes. Thank you etrailer!
# 5
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Fits perfectly, i like that it comes with the guide wires makes it all go smooth and easy! Install was maaaybe 30minutes and super simple, using it for winch set up, it is perfect (1993 chevy 1500 silverado extended cab) no modifications needed to my truck! Definitely a cheaper solution than to buying a modified bumper for winching. Nice sturdy product.
I installed this receiver hitch on the front of my Dad's 1991 Chevy Silverado so he could mount his winch to the front of his truck without having to buy a brush guard. Shipping was fast, I received the hitch in about 4 business days. The box was pretty banged up, it looked like the shipping company was using it as a shot putt but nothing inside was damaged. I do thing that it could have been packaged a little better. There was nothing to keep the hitch from moving around inside the box. Installation was a breeze! It came with all of the mounting hardware you need and even came with a wire to fish through the frame to pull the bolts through, which was a huge timesaver. All of the holes lined up perfectly and it fit snug in between the frame. I had it installed in about 25 minutes.
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~
Relatively easy install. Just have to be mechanically inclined. We use the hitch to carry a fish rack/cooler on a 2011 Jeep Wrangler. So far so good.
# 7
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2018 Ford F-350 Super DutyI installed this on the front of a 2018 F350. Fit an finish is great. Install was easy and directions simple to follow. Having another set of hands was very helpful, else it would be a balancing act I imagine. No drilling needed except for the cutout in the valence. My use is a cargo basket for four bikes and a kayak rack when pulling my fifth wheel. I have a receiver splitter that allows me to have both the basket and Yak rack mounted at the same time. Load up the toys and go...
A tight fit with the bash plates on my 2023 Ford F250. I also cut a 3 inch square air dam hole instead of 3 1/2. But had to extend the top of the hole due to the slope of the dam. The hitch pin hole barely clears the air dam. The hitch pin clip will rub on the air dam.
# 9
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.
I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
2007 Toyota TundraThis was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.
These is an excellent hitch at an excellent price. The install was easy and all the hardware that is needed is in the box. I chose the Drawtite over the Curt because the receiver end is a little longer. It' not even noticeable on the truck. I have a snow plow that attaches to the hitch. The Toyota cap shown in the picture was not included. The Tundra is a 2020 so I can confirm if fits.
# 11
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This is the third front hitch I have bought from etrailer. I use it in the winter for a snow sport snow plow and in the summer for a bike rack. I had one on a Nissan titan, and a Chevy silverado, plus other various hitches and hardware for cars and trucks. I have never had an issue with any of it. etrailer is by far the best hitch and towing accessory place I have dealt with. Never any issues with fit, form, or function. Plus they have excellent on-line help. And shop around if you find it cheaper else where they will refund 110% of the difference. You can' beat it. Only thing was I didn't just cut a hole in the lower valence because I didn't want to remove it so I had to slot it but no biggie. Plenty of ground clearance and it is a convenient distance out so you can't hit anything while it is not in use.
I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.
# 12
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
This fit my Ford 2023 E-450 (cutaway) perfectly. I had measured the frame of previous year E-450’s and didn’t see any difference so I gambled and ordered the 65053 which fit. Installation was straight forward with modification and fitting of the splash guard taking 50% of the time. Fit and finish was good except at the front of the receiver itself. Unfortunately that’s the only two inches of the whole hitch that show and had weld splatter and sharp bits under the paint. This took a bit of filling to smooth out which I then repainted. Attached are photos installed on my 2023 E-450.
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.
I chose this product because it was among the more inexpensive front hitches I could find. I plan to build a t-bar for it and use it in conjunction with a homemade headache rack to carry 16 foot garage doors. Like other reviews and vids I have found, the bolt up is hard. I reversed the bolts and use the new ones on the outside, as well as removing my grill. My truck is a 2003 - so not much room like the 2008 and newer trucks.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I'm off to overland in Texas and wanted you to know that the hitch and winch carrier are perfect. Using quick connectors, I can use ir on the front and rear. Removing it also saves on gas. It works great with a moulded number, saving on buying a specialized steel bumper and other expensive attachments. I like that I can still have all the internal mud guards and brush cover without having to take them off and not be able to have them on. Awesome!
This is a high quality hitch that fits the Gladiator perfectly. The hardest part of the installation was removing and reinstalling the push fasteners on the plastic air dam. While the hitch fit is perfect, the instructions for cutting the plastic air dam leave something to be desired. I finally had to eyeball the location for the hole and then found that the suggested utility knife simply wouldn't cut the plastic air dam. An oscillating saw solved the cutting problem easily and the best guess location worked out. Am I happy with the end result? You bet! Would I do it again? Absolutely.
# 15
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Thank gooness eTrailer was able to recommend a local hitch installer! Evidently somewhere along the line shipping or possibly the factory the receiver got "tweaked" and the installer couldn't easily line up the holes to install the bolts holding the receiver to the truck frame. I didn't ask about what type of "tuning" was required but suspect there were likely some hydraulics and chains involved. Great installer, without a lift and special "tuning tools" and experience, there's was NO WAY i could have installed the hitch with jack stands and conventional tools-thank you etrailer for sourcing local installers! Also I had to buy a separate ball and hitch as my rear hitch was significantly larger (and too lower in the front) when installed in the front receiver. Using a smaller hitch enabled me to easily move and disconnect from the trailer. Other than the unexpected "tweak" somewhere either in mfgr or likely shipping, I've been very pleased with the Draw-tite receiver. Excellent installation instructions with some clever installation methods.
UPS was rough on the box but everything still lined up without having to pry but was snug on the back bolts. Install was very straight forward and did it myself in my driveway in just about 90 minutes from pulling the air dam to putting tools away. Used my floor jack to support the hitch in the center and started with the front bolts on both sides and then pivoted the hitch into position for the back bolts and then snugged up all four mounting bolts to the 110-ftlbs torque spec. Hints. made sure that front of the hitch was just a a hair pointed up from level before tightening down all of the mounting bolts. I pulled the air dam completely off and then lined it back up in position lying on the hitch so I could marked it, so I knew exactly where I would need to trim it and then used my Dremel tool with a cutoff wheel to trim it to fit. Then bolted it back into position and was done. I'll try and update this post once I take some pictures other than the shipping box
# 16
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
It was a bit harder to put on than they show in the video. Did it by myself, everything fit perfect SO OWSOME! I would recommend anybody. Truck or car should add one. Very convenient and can be use for many different purposes.the rack on the back, I now put in the front with generator gas tools and it works as steps. So now I can tow trailer, or jet ski. Having that front hitch is so cool. You could even attach a car whinch in the receiver.
Got this on my 2006 2500 Ram. I did avoid drilling the holes over 1 inch (suggested in the directions) by loosening the bumper bolts and prying out some brackets in the frame ends temporarily (just to get the bolts fished thru). I pushed the brackets back in after getting the bolts in place (and believe the bumper bolts will squeeze them to hold them), but I did bend some tabs that I can't get back to original. My bumper bolts on the driver side wouldn't go in far enough (hitting a cooler) to be totally flush for a completely vertical lift into place, so I had to swing it up there first, then do the passenger side. The first pair of bolt fishing went good, but then I had trouble getting the wires off the bolts (they were tight enough that the more I tried to twist them off, the tighter they gripped it). So instead of them coming off like twisting a nut off, I ended up peeling them off (with the bolts staying stationary and my peeling the wire around them). That slightly bent the wires so they were slightly bigger than the threads and while fishing the second set, the wire didn't stay in the threads and jammed the bolt in the hole a bit (but I still got them in place). So watch how you treat the fishing wires until done. I already have a winch mounted on a hitch bracket, but may use this for more things besides that.
What our customers are saying:
"Excellent service and communication. Expect part to be excellent too!"