# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Product is well built. I needed an antisway tab on the opposite side from the product pictured online, so I called and asked whether etrailer had a separate tab that I could weld where I needed it. Etrailer had it and the two items arrived very quickly by mail. I now have the ball height I wanted and a good short distance from ball to bumper--and the antisway tab ball mount. The setup should be just right for towing my 16' Casita with the Chevy Trail Blazer.
This thing is a beast! The welds are perfect! This will never break. You will probably never need to buy another. I wish I could write more but, hey, It's a ball mount. Nuff said.
# 2
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 9" Long - 7.5K
Well built and just as shown, pleased with it.
Product is well built. I needed an antisway tab on the opposite side from the product pictured online, so I called and asked whether etrailer had a separate tab that I could weld where I needed it. Etrailer had it and the two items arrived very quickly by mail. I now have the ball height I wanted and a good short distance from ball to bumper--and the antisway tab ball mount. The setup should be just right for towing my 16' Casita with the Chevy Trail Blazer.
# 3
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 4
MaxxTow Ball Mount w/ 2" Accessory Receiver - 2" Hitches - 2-1/4" Drop - 5,000 lbs
Heavy duty , very good quality.
# 5
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
# 6
Draw-Tite Ball Mount for 2" Hitches - 1" Rise, 2" Drop - 8-1/2" Long - 16K
This is a beast of a drawbar, solid forged steel & well finished. It's also very heavy and E-Trailer needed to ship 3 times because the first two broke out of the box they were packed in. (Someone in the USPS has a couple nice draw bars.) Fortunately the 3rd effort was much better packed in a reinforced box and was successfully delivered. E-Trailer customer service was exemplary in resolving the shipment issue & I will definitely shop with them again.
A nice solid constructed hitch. It should handle everything I hook up to
# 7
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
Looks like a nice piece of work, and works great, just bought a utility trailer and brought back home.. Works like a champ..
Works great with my Blazer pulling my pop up camper.
# 8
Curt Forged Ball Mount for 2-1/2" Hitches - 1/2" Rise - 2" Drop - 20,000 lbs
Looks like a nice piece of work, and works great, just bought a utility trailer and brought back home.. Works like a champ..
Works great with my Blazer pulling my pop up camper.
# 9
Draw-Tite Ball Mount for 2" Hitches - 2-3/4" Rise, 4" Drop - 11-1/4" Long - 10K
Product is well built. I needed an antisway tab on the opposite side from the product pictured online, so I called and asked whether etrailer had a separate tab that I could weld where I needed it. Etrailer had it and the two items arrived very quickly by mail. I now have the ball height I wanted and a good short distance from ball to bumper--and the antisway tab ball mount. The setup should be just right for towing my 16' Casita with the Chevy Trail Blazer.
This thing is a beast! The welds are perfect! This will never break. You will probably never need to buy another. I wish I could write more but, hey, It's a ball mount. Nuff said.
# 10
Curt Ball Mount w/ Sway Control Tab for 2" Hitches - 3/4" Rise, 2" Drop - 7,500 lbs
I cannot use this ball mount because the shaft is too short that goes into hitch receiver on my one ton Dodge truck. It does not allow enough room between truck back bumper and ball to allow any trailer tongue to be put on ball.
Purchased this hitch as a companion for our Reese anti sway control. The small ball for the Reese sway control fits in the bracket and the 2” drop on the hitch is exactly what we needed to have our Jayco camper level when towing.
# 11
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
Product is well built. I needed an antisway tab on the opposite side from the product pictured online, so I called and asked whether etrailer had a separate tab that I could weld where I needed it. Etrailer had it and the two items arrived very quickly by mail. I now have the ball height I wanted and a good short distance from ball to bumper--and the antisway tab ball mount. The setup should be just right for towing my 16' Casita with the Chevy Trail Blazer.
This thing is a beast! The welds are perfect! This will never break. You will probably never need to buy another. I wish I could write more but, hey, It's a ball mount. Nuff said.
# 12
Brophy Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 13-1/4" Long - 10K
I’m pleased with the product and how prompt the delivery was. However the packaging was insufficient and the packaging was torn open all over. Scuffing of the finish is a result and of little consequence due to the intended use. It’s a stinger w/ball for motorhome. May I suggest better packaging in the future
Slightly longer, so you can open your tailgate with a cargo trailer attached. Trailers with a tongue jack that is forward are problematic for tailgates...
# 13
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This was the longest hitch ball mount I could find anywhere. I used it with a short extension for my 2021 T G so that I could open the back doors without hitting the trailer wheel crank. With my new trailer, Intact Flyer Discover, I don't need the extension and can still open the doors. Works well.
# 14
Convert-A-Ball Ball Mount for 2-1/2" Hitches - 3/4" Rise, 2" Drop - 18,000 lbs
I was very pleased with etralier for filling my order promptly. I was not pleased with usps.When the hitch arrived the box had been damaged. It was empty. I contacted etrailer about the problem. They were very helpful and offered me a refund or replacement. I chose the replacement. It was shipped promptly in good shape.It was a pleasure doing business with etrailer. Jon
Partial order. What I got was damaged and incomplete. The rest of the brake parts will be a few more days now….. will definitely not recommend
What our customers are saying:
"very easy to shop"