Yes, we do have the Replacement Feet # TE69FR for the 18' Reachable Telesteps Telescopic Ladder # TE74FR. We also have the Replacement Feet # TE39FR for the 14' Reachable Telesteps Telescopic Ladder # TE34FR. view full answer...
The Telesteps Ladder Standoff and Tool Tray # TE89FR is specifically designed to fit on Telesteps ladders like # TE44FR which have the oval vertical uprights. The uprights on the Lippert On-The-Go Telescopic Ladder # LC64HD are round and will not allow for the view full answer...
I recommend using the Telesteps Telescopic A-Frame Ladder # TE24FR. This A-frame ladder extends to 6' tall and the retracted ladder (29") can be stored in a smaller closet. The A-frame style also provides more support than a typical telescopic ladder. view full answer...
I have a solution for you. I reached out to Rhino-Rack, and they could not confirm for sure that the mounting brackets of the Folding Ladder for Rhino-Rack Pioneer Platform Racks - Aluminum # RRRAFL-RUFLB will be able to fit the channels on your Yakima LockNLoad # Y05048.
With that information, the safest bet is to go with a telescoping ladder like the Thule Telescoping Ladder for Vans - 9 Steps - 8-1/2' # TH301404. The reason why it is better to go with the Thule Telescoping ladder over... view full answer...
When it comes to replacing parts on The Thule Telescoping Ladder for Vans - 9 Steps - 8-1/2 foot # TH301404 we do not have replacement parts. You will have to purchase the whole kit.
The ladder can easily attach to the vehicle wall using the magnetic fixation kit which is included.
I attached a review video link below. view full answer...
Hey Scott,
The mounting bracket for the Telesteps Telescoping Pull Down Attic Ladder # TE84FR makes up the difference in height needed for a 10' high ceiling. view full answer...
Hi Allyson,
The Telesteps Telescopic A-Frame Ladder # TE57FR weighs approximately 26lbs and does not adjust to a 90 degree angle; this maxes out around 45 degrees. view full answer...
The Telesteps Telescoping Attic/Loft Ladder - 7' to 10' Tall Ceilings - 300lbs # TE84FR can only be installed on the vertical wall of the attic entrance to properly function. view full answer...
Thule currently does not offer any replacement parts for their Telescoping Ladder # TH301404. While we do not offer any similar magnetic mounts we do carry the SeaSucker Vacuum Mount # SS73FR. This mount is capable of 120lbs of pull strength without drilling any holes. You can place them on the rails of your ladder to help secure the top of the ladder to your van. view full answer...
The Telescoping Drop Ladder with Hand Grips # 315-EQB4 is made of 304 stainless steel. The Jif Marine ladders have always been made of 304 but there was an error listed in the manufacturer catalog. view full answer...
Hello Mark, thanks for reaching out. I went to our warehouse and measured the Telescoping Transom Drop Ladder # 315-DMX4. I measured 12" from the outside of the mounting brackets. I edited a picture to help illustrate. view full answer...
I spoke with Lippert about the mounting brackets for the Lippert On-The-Go Telescopic Ladder # LC64HD and found out that they are only sold as an OEM part. This means that only the motorhome/trailer manufacturer is able to order them so you wouldn't be able to get them aftermarket through anyone else. Going that route would most likely cost you quite a bit so you could try reaching out to a local fabricator to build you the mounting brackets since there's nothing really special to them. view full answer...
The only ladder that we carry that wouldn't require any modification for your 2016 RED 37PA Motorhome is the Telesteps Telescopic Ladder # TE74FR which is a telescoping ladder. It has an extended height of 14-1/2' and retracts to 35" for storage. This ladder weighs approximately 30.5lbs and is OSHA compliant and ANSI 14.2 tested. view full answer...
I was able to get my hands on the supplemental installation instructions for the Telesteps Telescoping Pull Down Attic Ladder # TE84FR, which I've attached below. For a complete manual you'll have to reach out to the manufacturer directly. view full answer...
Go To Results