I took a look at the online owner's manual for your 2018 Chrysler Pacifica, and it says flat towing with all four wheels on the ground is not allowed, but so long as it is a front-wheel drive, you can tow it behind your motorhome using a tow dolly. So with that in mind you have a couple of options, which are the Demco tow dollies:
- Demco Kar Kaddy SS Tow Dolly # DM9713045
The Kar Kaddy SS is a really nice, high-quality dolly that is much simpler to use than other tow dollies in large... view full answer...
Since you already have a 7-way trailer connector and a brake controller all you should need is the adapter to connect the controller. That's assuming the 7-way is factory installed. If you've installed it yourself, or had it installed aftermarket let me know.
If it's a factory 7-way there's going to be a connector under the dash above the steering column not far from where it goes through the firewall. The connector you're looking for probably has a green cover over it. Once you find... view full answer...
To add electric brakes to your 1998 Coleman pop up camper you should be able to use the Electric Trailer Brake Kit - Self-Adjusting # AKEBRK-35-SA and then hub and drum assembly # AKHD-545-35-EZ-K for a 5 on 4-1/2". You just need to make sure that your current bearings are # L68149 and # L44649 plus verify that your grease seal has an inner diameter of 1.719". If you have something else please let me know and I can let you know what alternative parts you need.
You also need to add a 7-Way... view full answer...
We do have a trailer hitch available for your 2018 Chrysler Pacifica hybrid.
The Curt Class III Trailer Hitch Receiver # C13383 is a confirmed fit for both the Platinum and Premium hybrid models.
If you will be using this hitch to tow a trailer then you will also need a hitch ball, ball mount, and trailer wiring.
The Curt Class III Ball Mount with 2" Ball - 2" Drop # C45036 is a great option to use but you will want to consult the attached ball mount article to determine if the 2"... view full answer...
No parts are more critical for the dependable performance of your trailer than the bearings, races, and seals. To ensure that your trailer performs reliably, you should inspect the bearings, races, and seals and repack the bearings every 12 months or 12,000 miles. If it has been past that time frame, there is a good chance that you will need a new bearing kt.
If you decide to replace your bearings, I will be happy to help you choose a kit. I will need to know the weight capacity of your... view full answer...
To tow a trailer with your 2015 Chrysler Town and Country I recommend the Curt T-Connector Vehicle Wiring Harness # C56331. It's a 4-way wiring connector to power the trailer's lights and it plugs in behind the van's tail lights. You also need to run a hot wire from the harness to the van's battery and insert the included fuse. I've linked the install details and a video from when we installed it.
If you also need a trailer hitch reciver I recommend the Draw-Tite, part # 75579, that's... view full answer...
Judging by the photo you've provided (thanks for the photo), you'll likely need the # C56399. Per fit information provided by Curt, the # C56399 which has the gray connectors is supposed to be a fit for the LX and the Touring models. I've provided a close-up shot of the connectors on the # C56399, when visually compared to what's shown in your photo it looks like a match.
The folks at Curt tell me that if you could provide me with your VIN, They can look up your vehicle and determine which... view full answer...
When installing The etrailer hitch # e98854 onto your 2016 Chrysler Town and Country it uses the existing M10 and M12 bolts that should be present on your vehicle. Since your hardware is missing you will need to contact your vehicle's dealership to get the correct hardware. If you buy standard hardware from a hardware store it will take away the warranty of your trailer hitch. The etrailer hitch in my opinion is the best hitch that we offer for your Chrysler Town and Country because it... view full answer...
In October of 2004, Kwikee began shipping steps with an integrated motor/gear box/linkage (IMGL). If yours is older than 2004 then you should use item # LC379146. The Replacement Motor for Kwikee 42 Series Electric RV Steps item # LC379167 you referenced fits step series 42. These parts will have no issue working together.
The IGML motor is Replacement Motor for Kwikee Electric RV Steps - 12V item # LC379147. The replacement module you would need is item # LC379605. view full answer...
It looks like the hitches for the 2011 Chrysler Town and Country use the bolts that are already drilled into the vehicle.
I've linked to a video installation of the Draw-Tite Hitch, part # 75579, so you can see how it works.
As for the size of the bolts, looking at the installation instructions for this hitch (also linked below), it looks like they are a mix of M12 and M10 bolts. You can find these at your local hardware store. view full answer...
When it comes to installing a hitch on your 2022 Chrysler Pacifica Pinnacle Hybrid # C29UR will not fit your vehicle.
Per the manufacturer The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2 inch # C13383 will bolt right up to the frame of your vehicle. It has a gross towing weight up to 4,000 pounds and a tongue weight up to 400 pounds. I would check your manual to find out what the proper towing capacity is for your vehicle.
Depending on if you will towing a trailer or not... view full answer...
In addition to the Roadmaster Tracker # RM-020 tow bar you referenced, you will need a base plate kit, safety cables, wiring and depending on the states you will be traveling in, a supplemental braking system.
The Roadmaster # 278-1, which fits all PT Cruiser models, is the base plate kit you would need. The base plates use removable draw bars that makes the base plate kit practically invisible when they are removed. Quick disconnects like part # RM-201 will also be needed.
The # RM-645... view full answer...
You will not need a brake controller to tow a boat trailer with surge brakes. Surge brakes are actuated by an actuating coupler on the trailer, so all you will need is a trailer wiring harness for the lights and an electric lockout, if your actuating coupler has an electric lockout. You can tell if your actuating coupler has an electric lockout by looking at the trailer connector. If you have a 5-pin trailer connector, then you likely have an electric lockout on your coupler. If you have... view full answer...
Thank you for providing the bearing numbers and other part numbers from the repair parts manual for your 1999 Coleman Grand Touring Series Santa Fe 3389 Pop-Up camper. Based on the bearings and bolt pattern for your existing idler hubs, we can determine the correct parts to add electric brakes to your trailer.
The components needed to add electric brakes to a trailer are an electric brake compatible hub and drum, brake assemblies, a brake mounting flange, trailer wiring, a breakaway kit,... view full answer...
You can install the etrailer Horizontal E-Track # e62VR and drive over it just fine with a vehicle as the tracks only sit 1/2" tall - then you can secure your side by sides with a tie-down kit like part # EM98CV you were looking at.
To secure the front wheel of your dirt bikes I recommend picking up a few of the CargoSmart Motorcycle Wheel Chock # 3481731 as well as a few of the single E-Track connections # SLSZ since the wheel chock connection points won't be as far apart as what you'll... view full answer...
We do have a few different options for you to add a backup alarm on your 2018 Chrysler Pacifica.
You could either use the Hopkins Backup Alert # HM20101VA which plugs into your 4-Way flat connector and lights up as well as emits sound when you are backing up.
Another option that doesn't involve utilizing a light is the Light-Duty to Medium-Duty Back-Up Alarm # PK41820. You will just need to ground the black wire and then run the red wire to your backup circuit.
Some review articles have... view full answer...
To transport a kayak with your 2022 Chrysler Pacifica we'll need to get you a trailer hitch so you can tow a roof rack on wheels since there currently (as of May 2023) aren't any roof rack options for your vehicle aside from what it comes from the factory with, and even that isn't compatible with the Hullavator.
For the trailer hitch I recommend the Curt Trailer Hitch Receiver # C65CR because it has a 2" receiver and hidden crosstube. Then for wiring you need the T-One # TK96FR along with... view full answer...
When it comes to installing trailer wiring on your 2017 Chrysler Pacifica The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118712 is confirmed to fit your vehicle.
The trailer harness has a simple plug and play installation that plugs into your vehicle's wiring harness, which is located behind the driver and passenger side tail lights. The harness will come out as a 4 pin flat connector.
To make the 4 flat connector to a 7 pin round connector The Universal Installation... view full answer...
According to Lipperts website you will want to replace your Series 42 step motor with the Replacement Motor for Kwikee 25 Series Electric RV Steps - 12V item # LC369506. You will need a IGML control box like the Replacement Control Unit for Kwikee Electric RV Steps item # LC379146. view full answer...
Go To Results