Correct Trailer Wiring Harness for 2019 Chrysler Pacifica

Question

Question:

Months ago I bought the Curt 56322 based on your recommendation. The connectors will not mate. The 2 little ears on the female connectors are set differently. My stop/turn lights are not LEDs. Does that make a difference? My connectors are light blue/gray, not black, if that helps. I can send a picture. Do you have a harness for my car?

asked by: John G

0

Expert Reply:

Judging by the photo you've provided (thanks for the photo), you'll likely need the # C56399. Per fit information provided by Curt, the # C56399 which has the gray connectors is supposed to be a fit for the LX and the Touring models. I've provided a close-up shot of the connectors on the # C56399, when visually compared to what's shown in your photo it looks like a match.

The folks at Curt tell me that if you could provide me with your VIN, They can look up your vehicle and determine which is the correct T-Connector for your vehicle.

expert reply by: Mike L

0

click to enlarge

Answer 1

Hello Shara, thanks for reaching out. I see that you already ordered the #e98903 hitch which is for the 2025 Pacifica, but I wanted to reply anyway to make sure all your questions were answered. To answer your first question, we do have a video…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Correct Trailer Wiring Harness for 2019 Chrysler Pacifica

Products Featured in This Question

Continue Researching