Hey Les,
The TorkLift SuperTruss Hitch Extension # TLE1536 you were looking at is exclusively for TorkLift's SuperHitch so you'd have to replace the factory hitch with part # TL74FR in order to use it. There are other hitch extenders available but they'll reduce the capacity of your trailer hitch by 50% and won't be nearly as long as the SuperTruss extenders. Do you know how long of an extender you need to clear the truck bed camper? view full answer...
Hey Javier, great questions!
Air bags are the absolute best for 5th wheel towing because you can adjust them on an as-needed basis plus you can add an air compressor kit to the mix so you really can adjust them on the fly as well as have air on site for different things you might need while out on the road and at the campsite.
For your application I recommend the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs # F2709 because they are the most rugged and offer the most support... view full answer...
Hey Steve thanks for the pictures. Without that pin box sticker or a part number you'll need to measure the bolt spacing and pattern on your pin box. I have linked a faq below that will walk you through the process.
Once you get this information or if you have any additional questions, go ahead and throw them into the comment box below and I'll be happy to answer them and find you the right goosebox. view full answer...
Hey Ismael, I wasn't able to find any cameras with the part number vccs150 but if you have a Voyager camera and the cable connector looks like what you can see in the attached picture this will work for you. Let me know if you need something different or have a different part number. view full answer...
Hey Matt, congrats on the new 5th wheel trailer. Do you know what pin box is on the Brinkley Z3100 you're buying? There's quite a few different bolt patterns and there's no database that shows me what pin box is on a trailer.
The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item # GY48GR you were looking at will only replace a Turning Point pin box. Now those are typically clearly labeled as being a Turning Point. Rhino-Box is another one that's easily identifiable.
If... view full answer...
Hey Adam, thanks for reaching out!
It sounds like you're either looking for a 24" fabrication part like the Buyers Products Weld-On Receiver Tube with 2" Hitch Receiver # 337RT25824B, or an extender piece like the 18" Extender # e48YR.
If you need the latter in a 24" length then you'll need to fabricate that because the only ones longer than this 18" extension are specialized ones for a dual receiver setup. view full answer...
Hello Garrett,
Thank you for the pictures, they were most helpful.
You were right on the money, the Replacement Pitch Arm for Solera XL Flat RV Awnings w/ 63" Long Support Arms - Black - Qty 1 # LC67VR is the part that you will need.
What happened to the other arm? Was it wind? view full answer...
Hey Vince, yes the Curt Q25 fixed hitch part # C97FR can be used in the bed of your 2025 Chevy Silverado 3500 with OEM pucks. This is a fixed hitch which means it doesn't have a way to gain additional turning clearance like what is normally needed with short bed trucks like yours...HOWEVER nowadays most fifth wheel campers have tapered noses or pivoting pin boxes to allow for short bed turning clearance that does not require a slider so most likely this will work just fine for you.
If... view full answer...
Hey Bill, Yes the Weigh Safe adjustable ball mount with scale part # WS46ZR that you referenced can be used with a Rock Tamers mud flap setup for a 2.5 inch hitch like the part # ERT00110. Do you have a car hauler that you are towing? view full answer...
Hey Clark, so for a tandem slipper spring hanger kit designed for 38 inch wheelbases is the part # HAP-105-205-01. Then for the slipper springs you'd need the part # e74SR and you'd be set.
For a u-bolt kit that is compatible with the 2 inch wide springs that I mentioned you'd then also need the part # APUBR-8. view full answer...
Hey Kaysie, thanks for reaching out!
Yes, the B&B Top Rear Corner Trim Cover for RV Seam # BM65XR will work for both the left- and right-hand sides of the RV. Just make sure you don't use screws for the left side of the trailer for the right side and vice-versa (my attempt at humor...if it didn't work, please don't hold it against me).
Are both sides of the trailer in bad shape, or are you just needing one side and wanting to make sure you get the correct one? view full answer...
Hello Nic,
I believe you are referring to part of the turn buckles as that is the only "S" shaped part I can think of for the tie downs, I believe you need the Replacement Turnbuckle for TorkLift Basic SpringLoad Turnbuckle Kit - Qty 1 # TLS9012.
If that is not the piece you are looking for could you please send me a picture of one (hoping you did not lose them all). view full answer...
Hey Russ, for a vehicle like your 2025 Chevy Silverado that does not have a cigarette lighter power port you would need to source a USB to cigarette lighter adapter so that you could power something like the Furrion Vision S part # FOS43TASF that you referenced. view full answer...
Hey Janet, yes the Hollywood Racks RV Rider Bike Rack part # HLY64FR can be used with a 2.5 inch to 2 inch hitch reducer. Do you have one already? If not we have them like with our part # 58102. view full answer...
Hey Phil! The BAKFlip MX4 Hard Tonneau Cover # BAK448133 is approximately 3" thick when folded onto the front panel up at the cab of the truck. The panels are 1/2" thick but they don't fold perfectly flat and there is some other material in there as well. If you count where the latches sit it is closer to 4-1/2". Will that work for you? If not, you might want to consider a retractable cover like the Pace Edwards Switchblade # PE63CV. view full answer...
Hello Ross, thanks for reaching out. For the etrailer Swivel Jack w/ Bolt-On Mounting Plate # e22ZV the distance from the bottom of the pipe mount bracket to the bottom of the jack when fully retracted is 8". I edited a picture to illustrate. Let me know if there is anything else you need. view full answer...
Hey Kevin, the correct Torklift Camper Tie Downs you'd want for your 2022 Chevy Silverado 3500 dually would be the part # TL86NR. Do you need turnbuckles too? view full answer...
Hey David, the only way we can get those spacer blocks is if you order the part # RHK from us. You would need to know the hitch part number that the block came from as well. I know this option is more expensive than you'd probably want but we don't have a different way to get it. view full answer...
Hello Terry and Pam, thanks for getting in touch. So we do not have any kind of 7-way that would have two outlets. The best way to do this would be to add a 7-way to the bed using part # C53CR. This way you can have the factory 7-way on the back bumper, and another 7-way in the bed. This is the only way we are aware of to safely add a second 7-way outlet to a 2024 Chevy 3500, or any truck for that matter.
Reply below with any other questions or comments and I will get back to you. view full answer...
Hey Daryl, so for a fifth wheel hitch setup that has a 25k capacity I would go with the Curt A25 kit part # C43BV which comes with a really nice hitch that has an easy to use and quiet since it holds the king pin so tightly. It also comes with a custom install rail kit that doesn't require frame drilling as well. The hitch also has one of the wider height ranges of 13 to 17 inches so that will help dial in allowing your trailer to sit level too. Got any big trips planned? view full answer...
Go To Results