Hello Jim, thanks for reaching out. We do offer lift kits that can be used with the Dexter Torsion axles. Do you happen to know the weight capacity of the axle? The S/N seems to indicate a 3,500 lb axle but please do confirm. We offer lift kits for Dexter Torsion Axles in the following capacities:
2,000-lb capacity # K71-723-01
2,300-4,000-lb capacities # K71-707-01
4,100-6,000-lb capacities # DX56CR view full answer...
Hey Justin, thanks for reaching out. We should have a tail light replacement for you, but those lights aren't make and model specific, so there isn't a way to look up your camper to know exactly which light it uses. I can still point you in the right direction though.
Looking at pictures of the 2021 Grand Design 278bh online, the rear tail lights appear to be oval surface mount lights which is something we carry. I'd just want to make sure we match up the size and mounting style.
For... view full answer...
Hey Steve,
I just want to make sure I’m understanding your question correctly. Are you looking to set the pivot arm height on your B&W Companion # BWRVK3500? If so, that will come down to a couple quick measurements.
To find the right height for your fifth-wheel hitch, you’ll want to measure from the ground to the bottom of the king pin, and then from the ground to the top of your truck bed. From there, subtract the bed height from the king pin height to get the correct hitch height setting.
The... view full answer...
Hello Shirley, thanks for reaching out. The LaSalle Bristol Double Bowl RV Kitchen Sink - 27" Long x 16" Wide # 34413TLSB27167 will drop into a 27-1/2" x 14-1/2" hole, but the overall width of the sink including the flange is only 27" so you'd end up with a small gap that would have to be filled or covered. Generally, you want the hole to be at least 3/4" smaller than the sink flange itself which is 27" x 16". view full answer...
Hey, David!
Great question. When the Curt Tow Bar 7-Way Coiled Power Cord # C39HR isn’t stretched, it measures about 3 feet end to end. The coiled section is just under a foot, with straight sections on each side about the same length.
I attached a photo of the measurement for you as well.
What kind of travel plans do you have for the year so far? view full answer...
Hey Dwight,
The actual tray itself that slides out on the MORryde Cargo Tray # MR84FR measures at 16-7/8" wide. As much as I would like to say that will fit, I think it will be too close for it to work. You may be able to physically install it, but then the function that makes it so great wouldn't actually work. That is the smallest size that we carry, but I would recommend giving MORryde a call. They may be able to custom make one, or maybe even have a size that fits your application... view full answer...
Hey Susan, welcome back. The JR Products Magnetic Baggage Door Catch item # JR44ZR measures 5.50" long x 1.88" wide x 1.13" tall. The distance between the mounting holes is 4" on center.
It is also available in black with the Magnetic Baggage Door Catch item # JR64ZR. The dimensions are the same as the white one.
What are the dimensions of the magnetic catches you're needing to replace?
You can add this information, along with any other questions you have, where it says Add Comment. view full answer...
Hello Mike, thanks for reaching out. The picture below will show you the mounting plate dimensions for the Fulton XLT 2-Speed Trailer Winch # F142425. I was not able to find any reference for the Fulton K20 jack bolt pattern, so I suggest you compare the measurements below to your jack and see if it is a match. Most Fulton jacks use a similar bolt pattern so you should be good.
Red - 2-3/4"
Blue - 4-1/8"
Green - 5-3/4"
Pink - 6-7/8" view full answer...
Hello Jim,
Thanks for writing in, I'm glad you found us!
I did some digging, and the 6 inch Rough Country lift uses replacement rear coil springs rather than the factory rear coils. Since the Air Lift 1000 Air Helper Springs # AL60769 install inside the rear coil springs, I can't confirm they'll fit with the aftermarket coils. Rough Country doesn't publish the inside dimensions of their replacement springs, and Air Lift only confirms fitment with factory-style rear coils.
If you can... view full answer...
Hey Austin, if the tongue weight rating of the Tahoe can be increased with the use of a weight distribution system it will be listed as having a second higher tongue weight capacity under a section that says "weight distribution". The non weight distribution capacity would be listed as "weight carrying."
I tried looking up the weight capacity of a Chevy Tahoe with a WD system and it doesn't look like it has an increased capacity when using one. view full answer...
Hey Rick. 3/8" is not going to be a deal breaker when using the Curt CrossWing Lightweight 5th Wheel Trailer Hitch item # C86JR. So long as you have plenty of clearance above your bed rails you'll be good.
To make towing with a 5th wheel easier, I recommend adding the Curt 5th Wheel/Gooseneck Custom Wiring Harness item # C56000. This harness puts a 7-way connector in the bed of your truck and allows you to keep the one on your bumper. This makes hooking up to your 5th wheel trailer easier... view full answer...
Hey Aaron, thanks for reaching out. Based on the specs I found online, the Americana Modular Wheel # AM92NR shares the same dimensions as your SRW 31767A9 trailer wheel. It has the same 17.5" x 6.75" size with 8 on 6.5" bolt pattern and -0.5" offset. It also has a 6,005lbs capacity with 4.76" pilot hole.
On a trailer wheel, a positive offset pushes the tire farther inboard toward the trailer frame and suspension. So with a +0.5" offset, the wheel mounting pad is 1/2" closer to the outside... view full answer...
Hey Kevin! The Classic Accessories item # CA80-300-203101-RT is good length wise for your 43' 10" long 2025 Jayco Pinnacle, however you're going to need to take a measurement to confirm it'll fit height wise. So long as the distance from the top of the roof to the bottom of your side wall, not to the ground, is less than 140" or 11-1/2' you'll be good. I can't find this information online just the overall height from the ground. view full answer...
Hey Bret! The 72" x 29" MORryde RV Cargo Slide Tray item # MR99FR weighs 117 lbs.
What are you looking to install this sliding tray in? view full answer...
Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you are not towing your trailer. These significantly affect the range of your suspension which can leave you with a stiff rigid feeling in the rear end. Plus if you hit a bump while there's weight on them they tend to bounce.
Instead, I recommend the SumoSprings... view full answer...
Hi Kevin,
You're just needing a weight distribution hitch with a larger drop shank. To pick out the right one we'll first need to know the tongue of the trailer while it's fully loaded. You can do this with a tongue weight scale # BTBRV44FR or you can measure using a highway weigh station.
Next you'll need to measure to see what size drop shank you need. To do this you'll measure down to the ground from the top of the inside of the trailer hitch receiver tube. On the trailer you'll... view full answer...
Hey Ray! Yes, the B&W Continuum Weight Distribution System w/ Sway Control # BW78FR is the right model for your Serenova 160LG. The only other option I might consider is the # BW94BR with the extra long shank. This will push back the trailer an additional 4" which is helpful if you want to lower your tailgate while connected to the trailer.
Both fit a 2" receiver which is what the 2023 Canyon Denali comes with from the factory. The tongue weight range is 600 - 1,600 lbs. Looks like your... view full answer...
Hey Jim Bob! The Blue Ox Leveling Kit with Wheel Chocks for Trailers and RVs item # BLU47UR only weighs 7-1/2 lbs. They come in a really nice carrying case too so transporting them and storing them will be pretty easy. They have a 30,000 lbs capacity and work with tires up to 32".
I have linked a review video below and attached a couple of pictures so you can see these wheel chocks in action. view full answer...
Hi Jeff; to find the right replacement leaf springs you will need to know your axle capacity and find their length. If you don't already know the capacity, check the axle tag to see if it is listed. If you only have a serial number the axle manufacturer will be able to identify it using that number.
I attached a help article below which explains how to measure your leaf springs. The most common measurements are eye to eye or the flat length. Once you have this information you can find... view full answer...
Hey Charles, thanks for reaching out!
My favorite roof rack storage rack is the 55" x 55" Inno Roof Deck Platform Rack # INA520 which is a simple platform, but some side rails can be added with the Rail Kit # IN57FR.
This rack is super easy to install because of the memory clamps, and it's made of aluminum so it's easy to move around and won't rust over time. I had the opportunity to install this on a Tacoma a few years ago so I'm adding that video for you to see my thoughts on it back... view full answer...
Go To Results