The Rhino Rack Vortex Crossbars # RRVA137B-2 you referenced measure 3-1/8" wide x 1-3/16" tall.
The Thule Motion XT Rooftop Cargo Box # TH629806 will fit crossbars that are up to 3-1/2" wide and 1-11/16" tall so they will work on these bars!
If you let me know the year, make and model of your vehicle I can confirm for you which Rhino Rack roof rack will fit and the parts you will need. view full answer...
According to Rhino Rack, the crossbars should be spaced 27-9/16 inches apart, center on center as shown in the provided diagram. Rhino rack chooses the specific mounting points for the crossbars based on where the strongest points of the roof are located. If you were to install the roof rack at a different distance apart, your rack would have an unknown weight capacity which could damage the rack or the vehicle roof if you unintentionally overloaded the rack.
If there was something specific... view full answer...
The only available trailer hitch we offer for a 2006 Scion xB is the Curt Trailer Hitch Receiver part # C11487 which is a direct bolt-on fit with no drilling required. This trailer hitch has a class I, 1-1/4" receiver which can be used for towing (if applicable) or hitch mounted accessories like bike racks and cargo carriers. If you will be towing however you'll also need the Curt # C56030 and Curt Towing Starter Kit part # C45147.
Unfortunately, there are no trailer hitch options from... view full answer...
Thule does not have a roof rack for your 2014 Scion iQ so I can't say for sure if the 1547 fit kit will work for you, but if you do decide to use that fit kit then I will give you some options to complete the roof rack.
The older Thule Traverse Fit Kit 1547 is compatible with Rapid Traverse Feet for Thule Crossbars - Naked Roof - Qty 4 # TH480R. You don't want to install crossbars that are wider than your vehicle due to safety and state laws; it looks like your 2014 Scion iQ has a width... view full answer...
You can tow your 2014 Scion XB with an automatic transmission but it must be dolly towed. The front wheels will need to be off the ground while towing.
I recommend using the Demco Kar Kaddy SS Tow Dolly # DM9713045 for your Scion. When not needed it folds up to nearly half of its normal length saving you space when not being used. The inclusion of surge activated disc brakes means that you won't have to install any additional brake controller inside your motorhome. view full answer...
To test the switch of the 12V RV Ceiling Fan w/ Wall Switch # 324-000053 you'll want to use a digital multimeter like # PT89ZR to test the power wire running to the switch. You should be getting 12v DC at the switch for it to properly function.
If the switch has 12v power and you have the switch on then you'll want to check the power at the fan to know if the switch is the issue or the fan itself is the issue.
If the switch doesn't have power then you'll need to trace the power wire... view full answer...
I am sorry to hear about your car accident!
The Curt Trailer Hitch Receiver # C11420 is a confirmed fit on a 2016 Scion iM, and 2017-2018 Toyota Corolla iM. If you plan on reusing the Curt Trailer Hitch Receiver # C11420 on another vehicle you will need new hardware # RHK. Make sure to include the item number for your trailer hitch receiver and manufacturer.
If you are in need of a trailer hitch receiver for your new vehicle, let me know the Year/Make/Model and I'd be happy to help find... view full answer...
The only hitch that fit your 2008 Scion xD is the Curt Trailer Hitch Receiver 11491 but that was discontinued back in 2020. (your photo didn't come through but I understand what type of hitch you're wanting)
With that being the case, we still have some alternatives for transporting a bike with your vehicle; with a trunk mount or roof mount bike rack.
A trunk mount rack, like the Thule Passage # TH910XT, is more cost-effective but it means you can't open up your rear hatch while it's installed... view full answer...
The Curt Trailer Hitch Receiver # C12490 is a custom fit for the 2011 Scion xB base model. The hitch fits this generation of the xB. The Release series center exhaust is on the 2010 model but we still don't list this as a confirmed fit because of the body kit on the 2011 Release. Your 2011 will mount the same way but you would need to modify your body kit by trimming to accommodate the receiver tube.
If you're looking to carry a bike rack or cargo I would get a roof rack. This will be... view full answer...
The Yakima FullBack # Y02634 will work well on your 2007 Scion tC. This bike carrier will work with the spoiler on your vehicle.
The bike carrier has four straps to secure the rack to your Scion, and the cradles hold the bike frames at three points. It also comes with locks for the rack and the bikes. view full answer...
The Draw-Tite # 24935 is a confirmed fit for your 2015 Scion FR-S and has a tongue weight rating of 200 lbs and a gross towing weight of 2,000 lbs so the hitch itself would be able to handle a small trailer like the Malone MicroSport # MPG461G2.
To complete a towing setup for your Scion FR-S you would need wiring like the Tekonsha T-One # 118629, a ball mount like the Draw-Tite # 3593, and a hitch ball like the 1-7/8" # 19256 or 2" # 19258. You will want to reference the linked ball mount... view full answer...
While we do have a great choice for a cargo carrier that will fit and work with your 2009 Scion xB, the one you mentioned won't work because it is a fit for 2 inch hitches only. The problem with that is your '09 xB only has 1-1/4 inch trailer hitch receivers available, with the best being the Class II Curt Trailer Hitch Receiver # C12490.
For a cargo carrier that will work with a 1-1/4 inch hitch and your Scion, I recommend the Curt Cargo Carrier # C18145.
This carrier - which you can... view full answer...
I reached out to my contact at Kodiak and they advised me that the Kodiak Disc Brake Kit 7,000 lbs # K2HR712D takes ½” studs only. When you go to 9/16” studs, the 7k axle kit # K2HR79DS comes with an 8K hub that takes that only takes the # 02475 bearing. Because you cannot fit 9/16” or 5/8” studs in a 7K hub Kodiak switches it to a 8 K hub. The 6K, 7K, and 8K spindle is the same spindle, the only difference is the outer bearing changes. view full answer...
Thanks for your recent purchase!
The Thule Helium Aero hitch mounted bike rack # TH9042PRO hand locking knob will not interfere with your Draw-Tite trailer hitch # 24827. The trailer hitch part 24827 is Class-I rated and has a 1-1/4 inch receiver opening and the rack is compatible with a Class-I trailer hitch.
The Helium Pro lets you lock your bikes to the rack and the rack to your vehicle for complete security. So, once you have tightened the rack in place you simply lock it with a key... view full answer...
You are correct that one of the hitches offered for the 2013 Scion xB, Draw-Tite Class I hitch # 24815, does not fit on the Release series. The other hitch offered is the Curt Class II model # C12490 and I confirmed with one of my technical contacts at Curt that it is compatible with the Release series version of the 2013 xB. Installation instructions and a video showing a 2014 xB are both linked for your reference.
This hitch will be compatible with Class II accessories that fit its 1-1/4-inch... view full answer...
The Thule Snug Tite Hitch Lock and Anti-Rattle Device # THSTL2 features a 1/2" pin diameter and is compatible with 1-1/4" and 2" hitches, however it is meant to be used with Thule hitch mounted racks. Most bike racks require a brand specific pin because they are threaded and the threads are usually different between bike racks. Since your Sportworks bike rack is older, none of these brand-specific bike rack hitch pin locks are guaranteed to fit your bike rack. I also reached out to Thule... view full answer...
The trailer hitch receiver we have available for your 2013 Scion xD is the Curt Class I # C11134. This is compatible with LED or without LED taillights on your vehicle. This hitch has a tongue weight capacity of 200 lbs max, but you will want to make sure your vehicle can handle that weight by checking your owners manual. This hitch does require the Curt Trailer Hitch Support Strap - Bike Rack Strap with Cambuckle # 18050 for non-trailer accessories.
The Bruno ASL-250 is 98 lbs, so... view full answer...
The Swagman Chinook 2-Bike Platform Rack # S64683 will work great for your application because it is compatible with a Class I hitch and it has a max rating of 45 lbs per bike. When you remove the battery from your E-Bike (which is recommended to reduce stress put on the battery) this will reduce the weight of your E-Bike to at least that 45 lb limit, it not put you under it.
Attached is a review video for you to check out. view full answer...
The Thule Passage # TH910XT does not require any tools for installation. It uses hooks on the straps to connect to your vehicle. I've attached the install instructions as well as video you can look at.
It will carry a woman's bike however since the bike will not have a straight cross tube you will need an adapter bar to keep the bike level. The Kuat Ubar Bike Frame Adapter Bar # UB01 is a great choice since it is spring-loaded to help establish a secure fit. view full answer...
The only trailer wiring harnesses that will fit your 2011 Scion tC are hardwire harness # C56175 or the Plug-in Harness # HM1141964. The T-connector style will not fit your tC. I have linked the installation instructions for you. view full answer...
Go To Results