Yes, the Draw Tite hitch part # 75282 is a confirmed fit for your 2009 Nissan Frontier and will work just fine with a full sized spare like what you see in the picture I attached. view full answer...
We do have an option for you as the Hopkins # HM43534 is only for the factory tow package. So because your 2021 Nissan Frontier does not have the factory tow package, you'll need a wiring kit that includes the relay jumper harness which connects to a 12-pin plug that is behind the kick panel on the passenger’s side in the cab. The correct part to add a 7-way is the following:
- Curt T-Connector Vehicle Wiring Harness # C56226
The relays and jumper harness of the # C56226 are not available... view full answer...
If you will be connecting the MB Sturgis Quick Disconnect Propane Hose for Small Appliance # 100476-120-MBS directly to your trailer then yes, it will work properly as long as the propane is being run through the camp stove regulator as well.
Be mindful that this hose cannot be used on a Coleman high-pressure product that is run off of a low-pressure propane system. view full answer...
In order to convert the hydraulic disc brakes on your trailer to electric, you will need a electric over hydraulic (EOH) actuator and a breakaway kit. The HydraStar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes part # HS381-8067 is an excellent actuator and will work well with your Tekonsha Prodigy P3 Electronic Trailer Brake Controller part # 90195.
For a breakaway kit I recommend taking a look at the Hopkins Engager Push-To-Test Trailer Breakaway Kit with Built-In Battery... view full answer...
The # HM43575 would work as a replacement, you would need to unplug your current harness and plug in the Hopkins in the 4-pole connector slot; you can see exactly where in the photo I've provided. I've also attached a link to a video review of this product for you to take a look at. view full answer...
I do have a way for you to determine if it will fit the OEM crossbars on your 2018 Nissan Frontier, but right off hand I don't know if the Rhino-Rack Fairing # RRRF1 is the correct size.
This fairing is compatible with crossbars that have max dimensions of 3-1/2" wide x 1-1/4" tall and that have a minimum height of 7/8". As long as you have at least 26" of space between your crossbar legs this will fit for your application.
Let me know if this isn't compatible with your crossbar and... view full answer...
I am assuming you are referring to a ladder rack for your 2013 Nissan Frontier, if this is the case then we do have several options that work with the factory Utili-Track System.
I recommend using the Erickson Truck Bed Ladder Rack part # EM07705 as this is one of our most popular ladder rack systems. Capable of weight capacities up to 800 lbs The Erickson Ladder rack has bed rail attaches that do not interfere with the Utili-Track's in addition to being adjustable to allow for different... view full answer...
Are there a lot of lights on the trailer? It sounds like maybe the trailer is wanting to draw more amperage than the Nissan is putting out on the trailer wiring circuits but your Chevy truck happens to have more capacity. When you say the lights short out do you mean they just don't turn on?
One way to lower the amperage draw of a trailer's lighting is convert the incandescent bulbs/fixtures to LED as they draw considerably less. I attached a page that has all of the LED trailer taillights... view full answer...
The Pace Edwards JackRabbit Retractable Hard Tonneau Cover # 311-JRN3857 that you referenced is confirmed to fit and will work perfectly on your 2010 Nissan Frontier that's equipped with the factory Utili-Track Rails. The cover will actually tie right into the rails via track nuts that will insert into their channel and provide an attachment point for the tonneau clamps.
Even with the clamps installed onto the Utili-Tracks, the tracks themselves will still be completely accessible around... view full answer...
Equal-i-zer weight distribution system # EQ37040ET, which is the same as the product you referenced does not require a 2-5/16" hitch ball; I took a look at the Equal-i-zer site and could not find a reference to that. However, if you need a 2-5/16" ball then the right one would be the 2-5/16" Hitch Ball for Equal-i-zer Weight Distribution Systems # EQ91-00-6100. It is also recommended you use Thin Walled Socket for Equal-i-zer Hitches # EQ70-00-4800 to make installation of this ball a little... view full answer...
It does; the "Manual Transmission" spec on the page is due to the fact that only the manual transmission for your 2021 Nissan Frontier can be flat towed, unless you get a drive shaft disconnect like you are. But the transmission does not affect the fit of the base plates, so they will work on your '21 Frontier. Along with the base plates there are a number of other parts you'll need, which I'll go ahead and list out for you:
- Base Plate Kit: Roadmaster Direct-Connect Base Plate Kit #... view full answer...
This is correct. The Roadmaster # RM-344-3B Base Plate Kit will fit on a 2015 Nissan Frontier S, King Cab 4 Cylinder, 2wd manual transmission vehicle. These direct-connect base plates will work only with the Roadmaster tow bars that slide into a trailer hitch, such as the Sterling # RM-576, Blackhawk or Blackhawk 2 # RM-422, Falcon # RM-522 and Falcon 2 # RM-520 . These base plates will not work with tow bars that require a hitch ball. If you'd like to tow with a different tow bar than... view full answer...
The Draw-Tite Front Mount Trailer Hitch Receiver part # 65075 is a confirmed fit for a 2022-2023 Nissan Frontier Pro 4X. I check with Draw-Tite for you to confirm. It's the same front hitch as the previous generation so that is where there may be some confusion but it's a fit without any drilling required. view full answer...
The Kuat Sherpa 2.0 2-Bike Platform Rack # SH22G (Gray), # SH22B (Black) or # SH22P (Pearl) does not have a way to adjust the position of your bikes, but there will not be an issue with the bikes coming into contact or rubbing against each other. The reason for that is because there is 14 inches of space from center to center of where the bikes mount. So even if you have a pair of mountain bikes with long handlebars the bikes will not make any contact or rub up against each other in any... view full answer...
Unfortunately, the MaxxTow MaxxHaul Over-The-Cab Truck Bed Ladder Rack MT70232 will not work with a tonneau cover. Although, there are some options that will work for you depending on your bed size and whether you have a utili-track system. Once I have these specifications, I would love to help you find one that fits with a tonneau cover! view full answer...
The relays for the Curt # C56225 on your 2017 Nissan Frontier are the same as the ones that come with the Curt 7-Way # C56226. Since you already have the 7-way functionality from the relays that came with your 4-way you will be able to install and use the Hopkins # HM43534 without the need for additional parts. view full answer...
Yes, the RockyMounts DropTop Truck Bed and Utility Track Bike Rack # RKY57ZR is designed to work with both Toyota and Nissan's in-bed utility rails. view full answer...
The SumoSprings Solo Custom Helper Springs # SS46EV includes a 1/2" spacer, so when you install this kit on your Frontier you'll just need to make sure you have 1" of space between the axle and spring. If you don't have 1" of space then you'll need to add the included 1/2" spacer. view full answer...
You will want to select either the 1,400LB # SSR-612-40 or 1,800LB # SSR-612-47 SumoSprings Solo Custom Helper Springs for your 2024 Nissan Frontier King Cab. The only difference between these is the amount of capacity they are capable of supporting and the color of the part itself. If you are only occasionally hauling heavy loads the lighter option would work the best for you. These will have the least affect on the quality of your ride when unloaded as well. view full answer...
The Universal Mounting Panel for Redarc Tow-Pro Trailer Brake Controller Control Knob # 331-TPSI-001 is going to require a 1" diameter hole in order for it to fit in your blank panel spot. The face of the panel is approximately 1-1/16" wide x 1-1/2" tall. view full answer...
Go To Results