The B&W Continuum Weight Distribution System part # BW78FR won't allow for the tailgate to open fully as it ships. In order for this to happen you'd need to switch out the shank for a longer option which is still currently being developed and tested by B&W. That said, you could still open the tailgate most of the way as is you would just need to be careful resting it on the jack but this can vary from trailer to trailer
In regards to the B&W Continuum Weight Distribution System part #... view full answer...
The Off White Ceiling Garnish # FVK1060-80 will fit your application perfectly. It has the 6" leg that you'll need to cut down to fit your 5-1/4" application but aside from that everything else will match up perfectly.
If you need a White garnish instead you'll need part # FVK1060-81.
Attached is a review video of the white version for you to check out. view full answer...
We offer four different axle lift kits for the Dexter Torflex axles. The difference between these kits is based on the weight capacity of the axle or tandem axles.
There will be a tag on the axle shaft that will have the information needed to determine which lift kit is needed. The tag will have axle model listed and should list weight capacity and a serial number as well.
For a Dexter 11 axle the recommended lift kit will be # K71-724-02 for tandem axles rated 4.1K to 6K lbs. This kit... view full answer...
We do have exactly what you need for valve stem extensions for your 2021 Jayco Greyhawk 27U. Based on my research your motorhome has 16 inch dual wheels, and since you have wheel covers there is a specific part for that:
- Wheel Masters 4-Hose Inflation Kit - 16" to 19-1/2" Dually - Wheel Cover Mount # WM8208
The # WM8208 comes with four hoses for the dual rear tires and 45-degree extenders for the front tires. view full answer...
The absolute best storage cover we have for your 2019 Jayco Hummingbird 17RK is the Classic Accessories PolyPRO 3 R-Pod Trailer Cover part # CA80-197-171001-00. This cover is going to provide protection in all seasons. It has adjustable front and rear tension panels for a tight fit and integrated air vents to reduce moisture buildup. It also comes with a drawstring bag when not in use.
As you can see in the attached photo on a similar 2017 Jayco Hummingbird 17RB, this cover is a perfect... view full answer...
You can raise the height of the trailer if you have double-eye leaf springs in the underslung position. This is done by using an over-under conversion kit like # K71-384-00 (for 2-3/8" axles) or # K71-385-00 (for 3" axles) to move the leaf springs above the axle, increasing the height by the diameter of the axle. These kits include everything you need, including spring seats, nuts, U-bolts, and tie plates.
This isn't necessary though since you can just use shank with a larger drop to keep... view full answer...
We do have a really good option to replace your 32 inch Jensen JE3208 RV TV, and even have one that fits the same mounting bracket. The part number is the following:
- 1080P Resolution: Jensen LED RV Smart TV # ASA38VR
This is a 110V TV that will fit a mounting bracket with the same 100 mm x 100 mm VESA mounting pattern your current TV has. view full answer...
Thanks for all that detailed info, and Atwood is out of business which is why you can't find the exact replacement. We do have an option for you, that will bolt on, with the caveat being you will likely have to use shims. The reason for that is the only option to replace it is a bolt-on coupler meant for 3" wide channel tongues, so it won't be quite 3-1/2" wide.
So what I recommend is one from Titan, which does have mounting holes 3" apart on center like yours, but you will also need to... view full answer...
The MB Sturgis Propane Pigtail - Stainless Overbraid - Type 1 x 1/4" Male Inverted Flare - 15" # 100833-15 is an 1/4" inverted flare tip and your regulator requires a standard 1/4" NPT fitting. You just need a pigtail like Propane Hose with Back Check - Type 1 x 1/4" Male NPT - 15" # 37207-30855.
I've attached our help guide article below which goes over all of the different propane fitting types and offers a ton of additional information. I've also attached a picture of a NPT and MIF... view full answer...
I have attached our 14" diameter trailer wheels for you. In order to determine the correct center cap I would need you to try and find your wheels below or send me a photo. Once done so I can see if we have options for you. view full answer...
The dimensions I'm seeing for a Suburban SW6DEL show it being 12.69"h x 12.69"w x 19.19"d so the Furrion RV Tankless Water Heater # FR98SR would most likely match up perfectly or require you to trim the opening by 1/8". The water inlet/outlet locations are a bit different than both the Furrion and Fogatti units so you may have to make some minor modifications to hook up your lines.
I receive a lot of troubleshooting questions with Fogatti units so I'm very hesitant to ever recommend one... view full answer...
I do have an option for you but there would be no way to lift your trailer using your existing half torsion axle system as they just don't make anything to allow for this. The only option you have to raise the trailer would be to install a new system with built-in lift like the Timbren Axle-Less Trailer Suspension System part # ASR3500S06 which will retain the same torsion axle design and install in a very similar fashion which you can see in the attached install video. This will be the... view full answer...
Yes, when using your turn signals the monitor of your Furrion Vision S Wireless RV Backup Camera System w/ 3 Cameras - 5" Screen # FCE48TASL-05 will switch to the corresponding side marker camera.
You will need to ensure that you have "LCD Auto" off in your settings and that your monitor is in "View ALL" mode. You can get to view all mode by double tapping the screen and in the bottom left corner "View All" will pop up for you to press. A few seconds after you turn off the turn signal... view full answer...
You are on the right track of choosing an upgrade for the Lippert pin box on your 2017 Jayco Seismic Wave 355W. Since the pin box is a 1621HD instead of a regular 1621 you need to go with a different pin box as the Curt Flex Air # LC328492 is only compatible as a 1621 replacement.
If you like the Curt line then you can use the Curt Air Ride # LC158778. This is rated for 21,000 lbs and the only difference between this and the Flex Air is that the Flex Air has a pivoting head which further... view full answer...
The Dometic 320 Full-Timer RV Toilet, available in Tan # DOM27FR or White # DOM87FR, is a great selection for replacing/adding/upgrading a toilet in your Jayco!
To determine if this will fit in your bathroom you need to have at least 11" from the center of the flange in the floor to the wall that's at the back of the toilet (also known as the "rough-in" measurement). If you have less than 11" let me know and I can help you find a different replacement, otherwise if you do have the 11"... view full answer...
We do carry a large selection of LED tail lights and we will undoubtedly have ones that will work for your 2000 Jayco Eagle M-12 UDK pop-up camper, though we do not have a parts list available for specific trailers.
The best way for you to find new LED lights would be to measure your current lights and find a close match. For example, tail lights # TLL12RK are 7-9/16" long x 2-3/4" tall x 3/4" deep and recess mounted, while # TLL9RK are 5-1/16" long x 4-9/16" tall x 2-5/8" deep and surface... view full answer...
We do have the exact fit for the AquaShed cover you are seeking for your Jayco Jay Flight SLX 145RB travel trailer.
The correct part is the Adco SFS AquaShed Cover for Travel Trailer # 290-52238.
This cover does have three zippered panels on the right (passenger side) so no matter where your door is you can gain access to your trailer. view full answer...
It does sounds like from your description that these are the correct replacements for you. The mounting brackets are 27-1/8" wide which matches what you have. There are a few different ways to attach the steps like you said. There are the three top mounting points that will match your front bolt but there are also four on the outside (two front and two rear) that will allow you to attach them to the bracket on your Jayco Eagle. There are also three toward the middle of the back but these... view full answer...
Yes, you'd just need to reach out to a qualified welder and have them weld on spring seats like part # TRSS300 to the top side of the Trailer Axle Beam with Easy Grease Spindles # e45GR. It's super common to do for people who have an underslung setup and want to raise the height of the trailer.
When you remove the old axle you'll also want to replace the u-bolts with ones like part # CE23003 since they get stretched when torqued down and shouldn't be reused. view full answer...
Go To Results