The Replacement Lens # AST61B referenced in your question is designed for the Optronics # RVSTL61 and # RVST61 Trailer Tail Lights. The lens itself measures 8-5/8 inches long and 3-3/16 inches tall
Unfortunately trailer manufacturers do not keep a good record of smaller parts like these that they install at the factory so I am unable to verify if this is the exact replacement lens for the lights on your 2018 Grand Design Imagine. With that being said I took a look at some pictures of... view full answer...
Yes, the Die-Cast Grate for Furrion Range Cooktop - 2 Piece # CFSRE21SA002 will fit your FS17WB4-BL and be the correct replacement you are needing. view full answer...
Thank you for providing that information. Leaf springs like the ones you have now typically match the axle capacity on your trailer. Although adding leaf springs with a slightly higher capacity won't hurt, it also is not necessary. Based on the leaf springs and and other information I'm sure you have 3,500 lb axles. Your standard diameter for this capacity would be 2-3/8". In addition to the capacity you want the eye to eye length to match, so we are looking at 25-1/4" long leaf springs.
I... view full answer...
The Replacement Stainless Steel Top with Glass Cover for Furrion 2-in-1 Range Oven # C-FSRE21SA-SS-003 is designed to fit Furrion models FSRE17SASS, F1S21L02A-SS, or FSRE21SASS. The part number you have there, FDO12A-SS, is actually the Front Panel for Furrion 2-in-1 Range Oven Drawer. The front panel corresponds with some of the same range ovens, but not all of them so I can't confirm if it will work based on that part number. If you find that you have one of these model numbers then this... view full answer...
The shank that comes with the Fastway e2 weight distribution systems rated for 1,000 lbs/10,000 lbs is part # FA92-02-4100.
This shank does use the industry standard 1-1/4" adjustments so if you're needing something a little longer or taller I'm linking our selection of replacement weight distribution shanks for you to filter through. view full answer...
For a replacement circuit board you can use the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS. We have confirmed with MaxxAir that this is the correct for what you have. view full answer...
Since multiple MaxxAir Fans have the same features that you listed it's honestly best to first determine the exact model number you have before purchasing anything and end up not having it be compatible. I've listed below all the available circuit boards for the each model, if you have a tag on the vent listing the model number then we can identify the correct replacement. If not, you'll need to pull the circuit board and find the sticker on it that lists the model number. Once I have either... view full answer...
For each of your Lippert 3500lb axles you will need the following components.
Timken Inner Bearing & Race # TMK73VR Qty 2
Timken Outer Bearing & Race # TMK23VR Qty 2
etrailer Grease Seal # 58846 Qty 2
Grease Caps # RG04-040 Qty 1
We do not carry a Timken grease seal or caps in the size you need for your Lippert axle. view full answer...
We do carry the lens for the Gustafson 12V RV Porch Light # 277-000485 you were looking at with part # 291-000002. I was able to find a dimensional drawing of the lens for your current light but I do have the measurements for the lens (pictured below). I recommend measuring the lens area of your light so we can confirm the fitment. view full answer...
As you have a Lippert Tuning Point pin box the only replacement we have is the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box # GY48GR. This converts your 5th wheel to a gooseneck ball connection so you will need a gooseneck ball in your 2019 Chevrolet Silverado 4500 rather than a 5th wheel hitch. If you wish to keep your 5th wheel hitch you will need to get a new box from Lippert. view full answer...
For your 2016 Grand Design Reflection 29RS, we have two possibilities for replacement springs that work for 4400-lb axles.
You need to measure from the center of one eye of the leaf spring to the center of the other to get the proper length. However, since yours are flat, they have stretched quite a bit. So, an accurate measurement will be difficult. More than likely, you will need the 26"-long 6-Leaf Double-Eye Spring for 4,500-lb Trailer Axles, part # e27SR I've linked to a video review... view full answer...
You would need the Trivet Support Bumper # CFGH4ZSASSTRIVETSPRT. They replace the support bumper for your Furrion 3-burner gas cooktop.
We also have the replacement Furrion Grill Grates Gasket # FSRE21SA-014 they hold on the grill grate on your Furrion cooktop. view full answer...
The MaxxFan Plus Roof Vent w/ 12V Fan, Thermostat, and Remote - Powered Lift - 10 Speed - Smoke # MA00-04500K is the similar fan to the 4951ksc. The issue you are having with the fan and lid are likely the circuit board which can be replaced with # MA10A21275K. However, the issue could be as simple as replacing the rain sensor. The Replacement Rain Sensor for MaxxAir RV or Trailer Roof Vent Fans # MA34FR is what you need for that and the rain sensor going bad causes the lid to close... view full answer...
You can use the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS to replace your damaged 10A04751ksz MaxxAir circuit board. This is a direct replacement. view full answer...
The 10" x 2-1/4" Electric Brake Shoe/Lining # BP04-095 could possibly work, but I recommend going with the Replacement Shoe and Lining Kit for Manual Adjusting 10" Electric Brake Assembly # AKBRKR-S-10 instead because it is designed specifically for the AxleTek brake shoes.
Usually we recommend replacing your whole brake kit instead of just the brake shoes because some of the other internal components would need to be replaced soon too. If you want to go this route then the kit you need... view full answer...
We do indeed have the correct replacement for the 694656 control module; I checked with Lippert and you're right that there is a different part number that has taken its place, but is the correct replacement for your Ground Control 3.0 4-point leveling system. The correct part is the following:
- Replacement Control Module for Lippert Ground Control 3.0 Electric Leveling System # LC304136 view full answer...
Thank you for the image of your axle tag. Your Dexter 5,200lb axle uses a Grease Seal # GS-2250DL. We do have this as a Pair # RG06-070 for both of the hubs on one axle.
We also have the Bearing Kit # BK3-300 that will include the bearings along with races and a grease seal for one of your hubs. I recommend keeping one of these along with Grease # L11390 in your 2021 Grand Design Reflection 303RLS 5th wheel just in case you have a bearing go out on a road trip. view full answer...
I do have an option for you but the shock absorber for the B&W Companion OEM 5th-Wheel Hitch part # BWRVK3300 is not something we offer as B&W does not sell these since they do all repairs in house. Therefore, if you want to get this replaced you'd need to send the hitch off to them for repair. That said, what we can offer you is a new head, the Replacement Head Assembly for B&W Companion 5th Wheel Trailer Hitches part # BWRVC3006 which comes with a new shock absorber and this would allow... view full answer...
Thank you for the details!
The Road Armor line doesn't really have anything that matches up so we'll want to look at the MORryde and Dexter Axle options.
For the MORryde we have the kit # MR27ZR which is a little longer and lower but will still work out just fine since those greater measurements are still under an inch so I recommend going this route.
If you want something more exact then the Dexter E-Z Flex Suspension Kit # K71-653-00 is about the same length and height as what you... view full answer...
The MORryde cushioned suspension equalizers like the CRE3000 part # MR27ZR that you referenced do not affect the height of the trailer at all.
If you wanted to lift the trailer you could use the Correct Track lift kit part # RR23QX as well. view full answer...
Go To Results