To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Heavy towing or a loaded bed can make the rear sag and the front lift, throwing off braking and steering. The Timbren Rear Suspension Enhancement System adds up to 6,000 lbs of support above the rear axle to keep your stance level and stable under load. The hollow rubber springs compress progressively, getting stiffer as weight increases so your vehicle stays balanced whether you’re hauling gear, towing, or carrying uneven cargo.
Rough roads and heavy loads can beat up stock suspension. These Aeon hollow rubber springs cushion impacts and soak up bumps before they reach the cab. Acting as shock absorbers, they take the brunt of potholes and washboard surfaces to deliver a smoother ride even when fully loaded. By absorbing road shock, they also help extend the life of the factory suspension and keep things feeling solid mile after mile.
When a turn or a strong gust tries to push you around, each Timbren spring reacts on its own to stabilize that side of the vehicle. This independent action cuts down body roll and sway so you feel more planted through corners or when a trailer starts to move behind you. It also helps when loads aren’t perfectly centered in the bed—each spring only engages when needed to keep everything balanced.
There’s no compressor, air line, or gauge setup here—just solid rubber support that works automatically. The system bolts onto the frame rails using custom-fit brackets and replaces factory bump stops with no drilling required. With about 1" of clearance over the axle under light load, your stock suspension still moves freely for a comfortable unloaded ride, then firms up instantly when weight is added. It’s a simple one-time install built for years of dependable hauling support.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey guys, it's Jake here with etrailer. Today we've got John with us from Timbren. He's gonna tell us a little bit more about what separates Timbren from the competitors. I appreciate it, I'm glad to be here. Timbren is a suspension specialist. We're based in Whitby, Ontario, so we are a true manufacturer in Canada and we offer a wide range of suspension products from light duty, from commercial all the way up to Overlander, Sprinter applications and trailers.
Now we've talked about a few of the options you guys have and we have plenty of options on our website. Right. We've got the SES kits. We've got the axle-less suspension. Right.
We've got your new coil inserts that just came out recently. But what would you say is your bread-and-butter at Timbren Yeah, no, our SES, suspension enhancement system, is definitely our bread-and-butter. Came out in 2011, won a SEMA New Product Award for best truck suspension. And really, the evolution you just mentioned here, you know, starting in 1968 all the way through now, 2024. But the SES kits are really the core of who we are.
And if you, if you would say at, in the level of stiffness on the market, what would you, would you put yourself in more in a heavy duty side for the SES kits or is it more of a lighter duty Yeah, great question. Lighter duty, we certainly can have a product for commercial and heavy duty, but in '82 when SES was introduced, it was purposely introduced for that, that light duty market. So we start with 1500 and again, go all the way up, but by far really popular with that 1500, 2500 crowd. That kinda leads me into my next question. So we talked about, your specialty is kind of in the lighter duty, but do you have an option for the heavier duty for your sprinter vans and maybe for your truck bed campers Yeah, absolutely.
We do have SES kits for truck beds, truck campers with a higher center of gravity. That creates a new kind of set of problems with the sway side to side. So we have severe duty kits for those. And it uses a single convoluted AON versus a double convoluted to tackle that problem of side to side. And the same thing with the sprinter van. It uses a rectangular shape Aon, but it's there to do the same deal that side to side sway because they're so top heavy, it'll eliminate that. Okay. And then we've had an instance here at etrailer that we had a van that was very, very heavy on the one side. Is there anything that you guys can do personally to help, I would say, I guess customize that kit for that particular user Yeah, by all means we would want that individual to contact us. We would ask a couple questions, see where that weight is distributed and we can actually produce an AON with either a stiffer hardness or durometer or a softer durometer and that will help level it out. So yes, we can take care of that for 'em. And I think that'll really, really help people to get their rigs dialed in because who knows what they're putting in the campers afterwards, after they buy 'em. They come from the manufacturer already heavy on that side and they're trying to load stuff on the other side to try to even it out. But knowing that there's a solution that you can customize for your rig no matter what the weight is on either side is really, really cool. Yeah, absolutely. We're happy to take care of 'em and again, there's no charge for that. Awesome. Now to kind of wrap things up, what sets Timbren apart from a lot of other manufacturers out there Well, I think there's a couple things. We're a family run company and our longevity, you can't deny, 1968 to 2024 and our warranty, we have a lifetime warranty regardless of how old it is. We will take care of it, replace it, limited lifetime warranty, and the hundred day money back guarantee. Very cool. And that's whether or not you're the first owner Right. And yeah, we're not asking for receipt, who'd you buy it from It'll be taken care of. Just give us a ring and we'll take care of it for you. Very cool. Well thank you again for meeting with us. Appreciate it. It was a pleasure to work with you. Thank you.
Ratings & Reviews
Added these to my F250 Super Duty. I carry a golf cart on a Diamond back bed cover. Can be a little top heavy. Perfect addition to my suspension- greatly reduced the sway.
1.5" gap... it came with 1 spacer for each side. if i buy the spacer kit, what size are they ? i have a 2026 f350.
Helps prevent about 1/2" of sag with my 175lb-tongue weight trailer and easy to install.
Easy to install using basic hand tools, and stopped the "sag" when I hook up my Casita travel trailer
Easy install took about 20 minutes on my 2017 Ram 3500 SRW. Had about 1/2 inch clearance as recommended. Loaded up my 5th wheel (2350 hitch weight) and about 200 lbs of gear in the bed. Just got back from a 800 mile camping trip through mountains of TN. You can really feel the difference around those sharp corners and uneven surfaces. The truck felt firm and controlled not hard and jarring as some have mentioned. Going over those overpasses with the wonderfully smooth (Not) joists was greatly improved. The truck would squat and rebound again, with a firm controlled response. Driving without a load felt the same as before without them. I would highly recommend these! Ordering from etrailer continues to be my go to option!
Great product. The ride and body roll at the rear axle are notceably improved (1989 Ford E350 Class C RV , 27 ft). I give it 4 stars because the installation was slightly complicated due to the rear brake lines needing to be slightly bent to provide clearance for the U bolts supplied in the kit. Great product and wish it came in a 5000 lb version.
2,000 miles in on a trip from the east coast to the Canadian Rockies these work great while loaded and towing. Close to zero bounce while towing, I love them. Unloaded, however, the ride in my 2026 Tundra has gone south. There is a noticeable, abrupt stop of the units hitting the axle when going over any kind of bump. When I get home and back to regular driving, I may just take them off, its that bad.
I've had these on our tow rig for a year now and I added buy them again today if I needed them.these have worked much better than airbags for our coil spring rear suspension to handle the tongue weight of our trailer. The SUV sits level when the trailer is on and it handles bumps and sway better than the airbags did providing much more comfort to us in the vehicle. Unloaded, we don't really notice they are there, unless, we have all the kids and some friends loaded up and you will fell them work when going over bumps.i do all my maintenance on the vehicle's and inspect these regularly and I cant see any wear so far even though we've gone on 6 trips with our trailer with about 5000 miles doing so.
I cant say these are the best for every truck or SUV, but for ours it is the best and I definitely would recommend to others.
Well they are exactly what I thought it would be. Hard for me to say it's what I needed yet.
I installed them on a homemade trailer from a salvaged 2001 base model tacoma. Once I get finished building it out and have some weight in it I'll have a better idea. But from what I've seen so far on a couple test drives they should come into effect when needed.
For reference I building an Tacoma based trailer with an ARE Contractor topper with a Naturnest roof top tent on the very top. So to counter and sway these should be very helpful. At least I hope so. I'm not an engineer but I did stay at an Holliday Inn once.
The Timbren SES is a simple solution for rear squat when towing. When hitched to my 30' Airstream Globetrotter (8800 GVWR) with a tongue weight around 1200 lbs, my Silverado 2500HD had a bit more squat than is ideal. I shopped airbags but didn't want to spend ~$2K for the set up and didn't want the hassle of installation and forever chasing air leaks. The Timbren SES literally installs on the Silverado in about 15 minutes. So simple. No bags, no compressor, no wiring, no air lines, no leaks. And WAY less expensive to boot. Just returned form a 600+ mile trip and it towed flawlessly.
A very simple and straightforward installation once you get the oem bumper stops off (had a shop do that)
Timbren worked with me as I had a non OEM frame height (vehicle was lower than stock) to recommend the proper kit. Highly recommend contacting timbren if you are unsure of the proper kit to use. Ride is more stable. It does feel stiffer and less bouncy but am looking forward to seeing how it performs with my truck camper. Truck is a 1998 dodge ram 2500. Brake line over left side of axle needed to be secured to prevent damage.
The Timbren overload spring/bumper was east to install and did what it was supposed to do when I hitched up a camp trailer. These did not negatively affect the ride by any means and I don't have to worry about the troubles with air bags.
Stiffens and corrects kneel in rear end of 2023 Chevy Silverado 1500. You will notice a stiffening of the rear end suspension while unloaded, but it’s a fair trade off to prevent sagging and porpoising while towing. I found it easier to pull the rear wheels and work from the side than underneath the vehicle while installing.
The timbres bump stop is exactly the right height to meet the axel when the trailer is connected with all its weight onto the hitch. I have an Andersen weight distribution hitch and it levels out perfectly. The day picture is with the coach (Winn 2100bh) with factory equipment. The night picture is after the timbres are in place. Looks good.
It has been almost a year since I installed Timbren Suspension Enhancement Systems (DVF350 and DVR350R) on the front and rear of my 2003 Dodge RAM Van 3500. These bumpers replaced the OEM bump stops that were on my van. I like the Timbren bumpers much better than the OEM bump stops because they provide a progressively cushioned response for suspension compression when traveling over significant humps like speed bumps in a parking lot, or curb ramps into driveways. I did not like the abrupt stop the OEM bump stops provided when traveling over the same objects. I installed the Timbren rear bumpers first, and after a few months of use, I decided to add them to the front. In both cases, the front and rear Timbren bumpers were easy to install once the OEM bump stops were removed. Installation required reuse of the factory hardware. On my van, the Timbren bumpers are not always engaged. Under normal load and travel conditions the bumpers are relaxed and about 1/2” away from the suspension landing points. However, their presence is much appreciated and very noticeable when the van is carrying heavy loads or handling significant humps.
Absolutely Pleased with the TIMBRENS. They were easy to install, and took less than an hour to install both. I noticed a slight stiffness in the ride as the rear bounced over a bad roadway. Towing is great, with a nice level and smooth ride. I am glad that I did not order the heavier duty Timbrens, than what was recomended for my truck. I believe the ride would have been too stiff. If you look at the photos showing the timbrens, the truck is still lifted in the rear, so what you see is a big gap between the rubber, and the steal plate. When the truck is lowered, there's 1" of space as it should be. BTW, I have been purchasing from etrailer for years now, and I have to say that I have never had any issues with any orders. They are my go to folks for all of my vehicle suppension stuff and trailer stuff. You can't go wrong with buying from them.
My F53 was like driving a waterbed down the road. With the Timbrens, it’s a different vehicle. Should have installed them years ago. Etrailer is my go to for anything trailer. FAST shipping and prompt responses to questions or concerns.
2022 F250 Super Duty. Super easy to install. I have about 3/4" gap between the spring and the plate. Time will tell how they impact the ride quality and how much sag they mitigate with my 5th wheel hooked up.
Timbren Spring Helpers were exactly what I needed on my Tundra plus a spacer kit since I have a 3” TRD lift. They were packaged neatly, with proper hardware, and excellent instructions! They absolutely do exactly what they are supposed to do! Truck rides much better and helps level out the load!
I'm suitably impressed with the difference i feel.
I have about 250 lbs. of static load with my topper and Decked cargo system. This put my install gap with no spacers just under the reccomended 1 inch minimum.Then add a couple hundred more pounds hauling music gear 100 shows a year, and the stop is resting on the axle.
I feel the absorption of the Timbren material is better than the flimsy stock bump stops. More cushion.
Where i really feel the difference is in the stabilty of excessive side sway when turning while loaded.
I have a gig coming up that will involve some unpaved mountain roads to get there so I think i will have a real goid idea of how these Timbren's will perform.
Instalation took me about an hour at 11 p.m.
The product it of the highest quality in design and build.
And Etrailer is a company that I would not hesitate to buy from in the future.
Thanks Dee Dee.
You rawk!!
Great products and service !!
Great support too! ! ! !
Works great
The TTORLC2 levels my Land Cruiser when towing a travel trailer. It eliminates the 1-1/2” sag the 6500 lb. load places on the tow vehicle.
The installation was easily completed in my driveway with a floor jack, jack stands and an impact wrench.
It is a no touch product, install it and forget about it. It’s there whenever you need it.
If my land cruiser is not towing or loaded down with heavy cargo, it rides like a New York City cab with a million miles on the odometer with these things installed. The KDSS suspension used to ride as smooth as a Cadillac. I would only recommend this product for a truck dedicated to towing heavy loads.
The original set didn’t fit the intended vehicle. (Toyota Landcruiser) after a few a few rounds of information exchange Timbren sent proper replacement parts. One frame mount still needed modification to not interfere with spring movement. Since then they have been good.
James
3/2/2023
Still working well
Do you have a question about this Vehicle Suspension?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jenny N.
5/1/2024
Yes, I would agree with you. The Timbren springs are made of a high quality rubber which when it does not have that load, can make your ride rougher. I would take a look at a Sumo Springs option which have more give or air bags where you have more control over the PSI. I would be happy to look at your options if you want to tell me the year of your Land Cruiser.