Kat's Heaters Ether Start Fluid Injection System - 3.3L to 4.9L Engine - 12V - 18 oz - Automatic

2010 Lincoln Town Car - Kat's Heaters Ether Start Fluid Injection System - 3.3L to 4.9L Engine - 12V - 18 oz - Automatic

Just turn your ignition to inject ether fuel (not included) into your intake manifold and get fast, reliable startups in cold weather. Connects to battery - no need to plug anything in. Thermostat ensures fluid is only dispensed when needed.

Features:

• Automatic fluid injection system gives you fast, reliable startups in cold weather by injecting ether into the intake manifold
  • 18-oz Fuel cylinder with ether not included
• Automatic activation when you turn the ignition
  • No need to push a button, pull a cable, or have another person spray fluid as you turn the key
• Thermostat ensures that system will only activate when outside temperature is below 50 F
  • Ether won't be wasted in conditions that don't require its use
• No over-injection
  • Actuating valve meters out 5 - 6 cc of ether for each use to prevent engine overload
• Spray nozzle with built-in filter vaporizes the ether
  • Prevents manifold flashback
• Energy efficient to preserve your battery power
  • Requires only 6.5 volts to operate
  • Connects to 12-volt battery for power
• Simple installation - no need to drill into cab to install a button or knob for activation
• Virtually maintenance-free - just change out fuel cylinder when empty
• Kit includes:
  • 1 Spray nozzle
  • Engine block thermostat
  • Actuator valve assembly with cycling switch
  • Protective caps, plugs, and gaskets
  • 5' Nylon tubing
  • Mounting plate with clamps and hardware
  • 12' of 16-gauge wire with terminals
• Made in the USA

Specs:

• Application: gas and diesel vehicles
• Engine size: 3.3L - 4.9L
• 3-Year limited warranty

Ether Injection System

This ether fuel injection system offers a hassle-free way to get fast, reliable startups in cold weather. Once activated, a measured shot of ether is vaporized and sent into your intake manifold. This vapor serves as a catalyst for combustion, helping to ensure that your engine starts on the first try, even in cold temperatures. The system connects to your battery and only requires 6.5 volts to operate. Because you power it on with your vehicle instead of plugging it in, it is ideal for tractors, logging equipment, and other vehicles and machinery that can't be parked close to an outlet. Once the system is installed, there's nothing else that you need to do to maintain the system other than change out the fuel canister, which will need to be done after approximately 200 startups. This system is designed to work with an 18-oz canister of ether fast flash fuel (not included).

Automatic Operation

This Ether Start fuel injection system is automatically triggered when you turn the ignition in your vehicle. There's no need for a button or a knob to be mounted in your cab for activation. A thermostat is included to ensure that ether will only be injected in conditions that call for it. When you turn the ignition in your vehicle, the starter sends an electric current to the Ether Start's thermostat. If the ambient temperature is above 50 degrees Fahrenheit, then your engine should turn over normally and no ether will be dispensed. If it is below 50 F, the electrical current will continue to the actuating valve assembly where the ether will be released from the fuel canister into a separate metering chamber. This chamber meters out 5 - 6 cc of liquid ether and disperses it through the nozzle. The nozzle's built-in filter vaporizes the ether, which is then injected into the intake manifold as a vapor instead of a stream. For the most effective and smoothest start, install this system so that the nozzle orifice is perpendicular to the manifold length.

33220 Kat's Heaters Ether Start Fuel Injection System - 200 - 299 CID Engine - 12V - 18 oz - Automatic