Uni-Lite LED Trailer Clearance and Side Marker Light - Submersible - 2 Diodes - Round - Amber Lens
(668 reviews)
Price: $3.62
In Stock
Uni-Lite LED Trailer Clearance and Side Marker Light - Submersible - 2 Diodes - Round - Amber Lens
Item # MCL11AB
Our Price: $3.62
In Stock
Need help with installation?
Locate installers near me- All Info
- Reviews (668)
- Q & A (0)
- Videos (1)
- Photos
Optronics Trailer Lights - MCL11AB
- Clearance Lights
- Round
- LED Light
- Amber
- 3/4 Inch Diameter
- Recessed Mount
- Rear Clearance
- Side Marker
- Submersible Lights
- Optronics
3/4" Round. Waterproof mini trailer light with 2 amber LEDs functions as both a clearance light and a side marker light when properly mounted. Amber polycarbonate lens. Recessed mount with grommet (sold separately). 2-Wire pigtail. PC rated.
Features:
- Small, round trailer light functions as both a clearance light and a side marker light when properly mounted
- Sealed, waterproof construction is submersible
- LEDs make great replacements for incandescent lights
- Last 50 times longer
- More efficient - provide brighter light with less power output
- No bulbs to replace - no brittle filaments
- Polycarbonate lens and housing
- Amber LEDs with amber lens
- Recessed mount with grommet (sold separately)
- Installation requires a 3/4" hole at desired location
- 2-Wire pigtail - includes power lead and ground wire
- DOT compliant
- PC rated
Specs:
- Dimensions: 3/4" diameter x 7/8" deep
- Diodes: 2
- Power draw at 12.8 volts: 0.03 amps
- Lifetime warranty on LEDs
Sealed, Waterproof Trailer Light
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
PC-Rated Lights
A PC-rated light produces a 90-degree angle of light to either side of its centerline for a total of 180 degrees of coverage. This beam pattern can be clearly seen when you are standing directly in front of the light, as well as when you are standing on either side of the light. When properly installed, this type of light can function as both a front clearance light and a side marker light or as a rear clearance light and a side marker light.
MCL11AB Optronics Uni-Light Mini LED Side Marker/Clearance Trailer Taillight - PC Rated - Amber
California residents: click here
Video of Uni-Lite LED Trailer Clearance and Side Marker Light - Submersible - 2 Diodes - Round - Amber Lens
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for Optronics Trailer Lights - Clearance Lights - MCL11AB Review
Today, we're going to be taking a look at the Optronics unilight LED trailer clearance and sidemarker light. This small, round trailer light functions as both a clearance light and sidemarker light when properly mounted, completely sealed, waterproof design is submersible, and it's an LED system. Now, LEDs are going to make great replacements for incandescent lights. They last longer. They burn brighter, and they're much more efficient. You don't have to worry about replacing bulbs and you don't have to worry about brittle filaments.
That's a nice, strong, durable design. When it comes to the lens and housing, we're looking at a polycarbonate construction. It's going to be an Amber light, so it's going to have the Amber lens, two Amber LEDs, and it's designed to be a recessed mount installation with a mounting grommet. Your mounting grommet is sold separately. It's available here at etrailer.com.
The installation does require a 3/4" diameter hole at the desired mounting location, and it's a two wire design, so your wires are protected and then here at the end, you can see that they split. You're going to have a black wire, which is your power lead and you're going to have white wire, which is your ground wire. It's Department of Transportation compliant. It is a PC rated light. When it comes to the dimensions, it's a 3/4" diameter light. The length of the unit measures about 7/8".
It's going to contain two diodes, or two LEDs. When it comes to the power draw, at 12.8 volts, we're looking at 0.03 amps. Optronics puts a lifetime warranty on the LEDs. We're going to go ahead and hook it up to power, that way you can see what it looks like. We'll also turn off our overhead light, so you can see it in a lower light setting.
You can see, here, that it sends out a really bright, consistent signal. Again, it's going to contain two diodes, or two LEDs. The multi diode design really helps optimize the light output of the unit. That's going to do it for today's look at the Optronics unilight LED trailer clearance with the sidemarker light.
Customer Satisfaction Score:
87% were satisfied with this product
13% of customers were not satisfied
- Wrong item was ordered
Customer Reviews
Uni-Lite LED Trailer Clearance and Side Marker Light - Submersible - 2 Diodes - Round - Amber Lens - MCL11AB
Average Customer Rating: 4.8 out of 5 stars (668 Customer Reviews)
3/4" Round. Waterproof mini trailer light with 2 amber LEDs functions as both a clearance light and a side marker light when properly mounted. Amber polycarbonate lens. Recessed mount with grommet (sold separately). 2-Wire pigtail. PC rated.by: Michael 06/22/2023
After a year this light is working very well. It's bright and reliable.
by: Bob F10/05/2019
They have/had just what I needed to replace a light which a mouse or chipmunk chewed the wires off of. The lights work and look great. I ordered extras just incase they attach another set of wires.
by: Mark11/08/2018
Great quality and easy to install. Perfect marker lights for trailers
by: Chris 01/24/2022
Great product, excellent price, and fast shipping!!
by: Carleton03/28/2018
Nice light. Very bright
by: Steve10/02/2019
Will contact you folks again when I need more items.
by: Steve09/04/2019
Everything I ordered was great.
by: Scott 01/23/2022
by: John C - Arizona04/14/2015
These were designed as a clearance light application and at a great price. I bought them to use as turn signal lamps on my RZR. They are high quality and extremely bright when lit, so they work great for both applications. These guys have great parts at a great price and quick shipping. I would recommend them to anyone needing trailer/boat/lighting. Thanks guys.
by: Sean 11/04/2023
Product is spot on, fit finish and function. More importantly the whole ordering/delivery process worked to perfection. Our company was in a tight jam with one of our transport trailers and needed these lights pronto,
e-trailer came to our rescue and didn't even know it. That in itself proves that customer service is
e-trailers standard priority.
by: Greg09/20/2016
I bought a couple more of these two-diode LED clearance lights to add some more lighting to the rear of my kayak trailer. They work nice and are easy to install in 3/4" holes that I drilled through a piece of aluminum angle. The trailer has orange clearance lights on the front sides, red clearance lights on the back sides, the stop/turn/parking lights on the back, three red clearance lights on the back, and a white LED license plate light. It's really lit up and very visible at night from the rear and sides. Thanks to etrailer.com for great products and services!
My wife and I like to kayak, but we don't like to deal with putting our kayaks on roof racks on the top of a car. So I bought a used Load-Rite trailer that was designed to hold one Jet Ski, and added a frame made of slotted angle and 2x6 lumber to hold the kayaks, and a cargo box from Tractor Supply to hold kayak seats, life jackets, towels, sun-protection clothing, and some spare gear (ropes etc), and bought all new LED lighting from etrailer.com. The paddles are too long for the cargo box so they have to go in the car! The kayaks are tied down to the trailer with several ropes front and rear, so there is a lot of safety factor in the design....I don't worry about the kayaks coming off the trailer! The entire rig works great....when we return from a kayak trip we just back the trailer in the barn and it's ready to go for our next trip. I put a 5" diameter wheel on the trailer just behind the hitch so I can push it around on flat level surfaces. See the pictures.
by: David H08/31/2020
I have finally finished the install of the great products that I’ve purchased from Etrailer. Curt 24K 5th wheel hitch, the lube discs, the front receiver hitch tube, the Factory 7-way connector and 7 -way extension (I have 3 7-way plugs on my truck) and the countless number of LED lights. The service is amazing and the customer service I received was fabulous. I really like these folks as they were vary knowledgeable about what I was after and pointed me in the right direction to accomplish my end goal. Thanks to everyone at Etrailer. I couldn’t have done it all without you.
by: Billy M06/04/2016
Great item at a great price. Purchased 4 clear with red (2-diodes) to place in my rear step bumper in place of back up sensors for my older truck used as clearance/running lamps.
Fitment was up to me being had to locate rubber grommets to adapt to these smaller 3/4" lights to the 1 1/8" bumper holes.
I would give these 5 stars but for some reason the black wire is the HOT, while any automotive electrical item I be ever worked on the BLACK was the ground! Opposite here and recommend testing them before you hook up like I did then had to reverse wires..
Silly mistake on my part but why is the black (+) and white (-) ???
Otherwise they're bright and add to my otherwise dark OEM tail lights for increased safety. Pic shown is during daylight!
by: So Cal Beach Camper06/19/2017
Great addition to the basic, rear brake lights of a camp trailer.
I added these LED RED to the brake/turn function, within the existing, small holes in the rear bumper--much more apparent when stopping/turning.
These sealed LED lights are very common on larger trucks and trailers now. Easy to install and very robust assembly...priced right!
by: Bader 08/30/2014
They are low profile in the day, and very functional in the night with their brightness. I did not expect them to be this good. I wired them as marker lights for my rear fenders.
by: Eddie05/14/2021
I installed these on my home built teardrop. Worked out very well. Total current draw is under 400 mA for all lights.
by: Greg03/04/2023
I installed these lights on my old enclosed trailer because most of my old lights were broken after many years.
Very bright!
I did drill holes in my trailer because my old lights were big rectangular ones.
These and the led taillights I got really make my trailer much more visible.
by: Jobby J.01/02/2017
I actually purchased these lights to use as a side marker light on my Jeep Wranglers after installing after market fenders. Lights have worked fantastic up to this point
by: Mackay10/01/2015
Very well built, sturdy and totally sealed against moisture. I installed these into the top of my Haulmark enclosed trailer to act as clearance lights. Installation was a breeze, I just drilled a 3/4" hole with a step bit, wired all five lights together and tied it into the running lights of the trailer's harness. I put the ground against the steel frame. I went a step further and put a bead of clear marine grade silicone around the light to ensure no moisture makes it inside the trailer despite these being a tight fit. As you can see from the pictures, installation is clean and they're very bright, both day and night! I put one on either end, 6" from the sides and the three middles ones are spaced 10" apart. Similar to the clearance lights on a truck, I didn't use a template, just winged it.
by: Mary 08/23/2023
Got exactly what I ordered in a timely manor. Very pleased with my order and will order from this company again if I need something for my horse trailer!!
by: Joseph12/29/2019
Great little running light puck! Easy to install and very bright at night and is even very visible in daylight. Only about an inch in diameter on the outside, you wouldn't think it was much larger from the amount of light they provide.
by: Chris M.10/27/2013
Shipping was slow, but I can't complain much considering it was free!
I chopped the fenders on my 2008 Jeep Wrangler, which involved removing the side marker lights. I installed a pair of these DOT approved lights to meet inspection requirements.
As for the lights, they are well-constructed and very bright. Installation was difficult; even after drilling and deburring a 11/16" hole, the grommet barely fit in. I had to put a small amount of grease on the light's lateral surfaces before the light would slide into the grommets.
Overall, I am very pleased with the product. Poison Spyder sells an inferior product at several times the price; I am glad I found these here!
by: Mike Fritsch10/08/2019
I have purchased lights from etrailer several times and the service and quality have been great. I have purchased lights for my truck and also have used there submersible lights for my boat trailer.
lights have been in service for over a year and still bright as the first day I installed them.
by: Doug04/10/2019
I ordered these light to be used as accent light on a new lift table for my company. I needed low profile and fairly bright red light to be reflected off our off-white power coat. These little lights out preformed what we were hoping for. The only thing I don't like about them is the instructions say to drill a 11.16" hole. Assembly was WAY too tight at that dimension. So we stepped it up a fraction at a time and found that 17/64" (.73) and 3/4" (.75) were perfect. Even at 3/4" the grommet was snug and water tight. The light had to be squeezed into place but at 11/16" I felt like I was about to brake the light.
Overall I am super pleased with the lights. We added them to the Bill of Materials and we will be ordering them for these new carts.
by: James08/02/2018
Added these lights on my motorcycle trailer, and they are perfect!
25
616
Show More Reviews
See what our Experts say about this Optronics Trailer Lights
- How Do Uni-Lite LED Trailer Clearance and Side Marker Light Remove/InstallRemoving trailer clearance lights like the part # MCL11AB can be difficult. We have found that you need to push the whole assembly out from the back towards you including the grommet at the same time. You'll need to access the back side of the lights in the picture you submitted and push the lights out. I attached an install video for these lights that shows how they install for you to check out as well.
view full answer... - What is the Wire Gauge Size for Optronics Uni-Lite LED Trailer Clearance and Side Marker LightsThe gauge wire used for the Uni-Lite LED Trailer Clearance and Side Marker Light # MCL11AB and Uni-Lite LED Clearance and Side Marker Light w Grommet # MCL11RKB is 18. To account for the loss of power over the distance of the trailer we recommend using 16 Gauge Wire # 16-1-1 and Butt Connectors # DW05744-10 for the installation.
view full answer...
Do you have a question about this Trailer Light?
Info for this part was:
Edited by:
Leah B
Expert Research:
Jameson C
Installed by:
Cole B
Written by:
Amy B
Updated by:
Wilson B
Updated by:
Brian T
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.