1-11/16" Round. Waterproof trailer light serves as either a side marker or clearance light. Smooth, bright outer ring of light offers a unique look - chrome bezel sold separately. Surface mount. 2-Wire pigtail with 0.18 male bullets. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated or P3-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today, we're taking a look at the Optronics Glow Light, M3 LED Clearance or Side-Marker Light.This round trailer light, with a smooth, bright, outer band serves as either a side-marker light or a clearance light for your trailer.It does feature a sonically sealed design, so it's got the nice, waterproof housing and lens unit that is completely submersible. It's a full-LED system. LEDs make great replacements for incandescent lights. They last longer, burn brighter, and they're much more efficient. You don't have to worry about replacing bulbs or worry about brittle filaments.It's got the nice, clear lens with red LEDs, and a polycarbonate lens and housing that's strong and durable. Mounts on the surface of the trailer.
There is a small hole that will be required for the wiring to pass through. I did measure that, and it measured to be about 3/4 inches. So, I think a 3/4-inch diameter hole should work out really well.Mounting hardware is not included.It's a two-wire design, with the 0.18 male bullets on it for hardwired applications. Those can be cut off and the wiring can be stripped back, if desired.Also, there is a chrome bezel that's made for this unit. It offers a really nice, finished look.
It is sold separately and available at etrailer.com. This is a P2-rated light, and it's Department of Transportation compliant.A few measurements I want to go over with you real quick. Measuring edge-to-edge, from this point here to this point here, measures about 1 and 13/16ths of an inch. And it measures the same going this direction. The depth, from the mounting surface to the outer edge of the lens, was about 3/4 of an inch deep.
And then that lens has a diameter or about an inch and a half. The mount holes on this unit are separated on center by 1 and 3/4 inches.The light contains a total of five LEDs or five diodes. We're going to go ahead and hook it up to power. That way, you can see what it looks like with some power running to it. We'll also be able to turn off our overhead light so you can see it in a low-light setting.So, here, you can see, the light sends out a nice, strong, consistent signal, and you can really see that smooth outer band that goes around the perimeter of the unit.
When it comes to the power drill, at 12.8 volts, we're looking at 0.12 amps.That's going to do it for today's look at the Optronics Glow Light, M3 LED Clearance or Side-Marker Light.
Exactly what I needed to rewire my vintage trailer.
Best online company experience so far. Excellent communication that seems truly personable. Product was exactly as expected and looks great. Used as a side marker on the tongue of my aluminum PWC trailer along with rear tail glolights. Thanks again.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.