To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Some covers block access when you need to haul something big. This one folds up toward the cab so you can use the full bed without removing it. When open, latches secure it at a 90-degree angle for highway driving, so you can load large tools or gear without worrying about the cover bouncing around. It even leaves your stake pockets open so you can still mount racks or tie-downs.

The cover is built with extruded aluminum panels that can handle up to 400 lbs and stand up to hail or other impacts. The black urethane coating resists scratches and keeps its clean look even after years of use. When closed, the latches lock with your tailgate, so your gear stays secure and dry wherever you go.
You don’t need complicated hoses or fittings to keep the weather out. Built-in weather seals block rain and dust from getting into the bed, keeping your cargo dry through storms and car washes. The seal design also helps the cover stay flush with the rails for a tight, finished appearance.
Installing it is straightforward—no drilling required. The clamp-on system lines up with your bed rails and tightens down with simple hand tools. Once mounted, the low-profile design sits less than 1/2" above the rails, giving the truck a clean, factory look without bulky edges.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, neighbor. This is Curt with etrailer and today, we're gonna take a look at the Lomax Stance Hard Tonneau cover. Now, if you've had any experience with this tonneau cover or have questions about it, go ahead and leave those in the comments below. We love to take those and use them to help our other neighbors make the best decision for themselves. Now, if you have a truck that you're using quite a bit and you really want to be able to protect any of your gear or cargo in the back, a hard tonneau cover is a really good way to go. It's going to be a great anti-theft measure, especially as opposed to a soft tonneau cover, which while it'll protect from the elements, can be slashed open with a knife and somebody could get in and take your stuff outta the back if they really wanted to.
A hard tonneau cover like this is gonna eliminate that. It's made of aluminum. It's got a nice diamond pattern on the top. It really gives it a nice look, especially on a truck like this and it is gonna have a capacity on the top of around 400 pounds. Now, it is also a tri-fold cover and we'll show ya how that works and it also has the ability to fold completely open and anchor to points that we have installed up here on the roof.
So, before I get into the tailgate and show ya how it operates, I also wanted to point out that it is ladder rack compatible. It's gonna sit above your bed rails and it is gonna be outta the way enough that these stake pockets are gonna be accessible. Now, as we drop our tailgate here, we're gonna find a latch on the side right here. It's gonna drop this string down. We're gonna be able to pull that and remove our first section.
The second section has no latch. We'll be able to lift that right outta place. And this is generally what you're gonna do for bed access. This'll be enough to reach, ya know, your fifth wheel or anything like that if ya have one and give you a really good amount of space to get most of your stuff in and outta the vehicle. However, there are gonna be times where you're gonna need use of the entire bed.
And for that, we're gonna go ahead and put it in its complete upright position. It's easiest to do it from the bed. First, we're gonna go ahead and unlatch using the string right here. We'll pull that down, unlatch it, bring it into an upright position and once we're here, there are these little braces here that we could put down on this installed piece that we have here and what that's gonna do is keep it in an upright position while also not letting it rest against the back of the cab and the light that we have back there. So, once I have that deployed, while it's not recommended to drive in this position, if you needed full bed access, this would be the way to get it done. So, as we're gonna lower this back down, we're just gonna drop it into place. We'll make sure it latches completely on both sides, unfold the next section and as I'm unfolding, you notice that the entire tonneau cover is gonna be lined with this rubber seal. That's gonna do a great job of keeping out the elements and keeping your cargo dry. So now that we're gonna be here at the final section, all you're gonna need to do is get it dropped right down into place. (cover clicks) Make sure it latches here on both sides. And close our tailgate. It's really just that simple. This is an excellent choice for any truck. If you really are serious about protecting your cargo and keeping it outta the elements and keeping it safe from any of the uh, worse elements of society, criminals and thieves and such. So again, this is a really good choice for you and your truck. I'm Curt with etrailer. Thanks for stopping by.
Ratings & Reviews

Gwendolyn Y.
1/9/2025
Happy to hear that you still love your cover after a year, John!

John S.
1/15/2026
Still completely satisfied with the Lomax cover
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.




Matt
5/30/2025
After one year the cover is still working well. Its sturdy and locks in place nicely. Very fast to remove when I need the bed fully open. The rubber seal that installed near the rear window was not good the adhesive gave out after 3 months. I threw it away and the water intrusion is still very minimal. Other than that all is good.