Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,200 lbs TW

See what our Experts say about this Equal-i-zer Accessories and Parts

• Upgrading 1,000 lb Tongue Weight Equalizer System to 1,200 lb System Recommendation
  If you have a 1,000 lb tongue weight Equalizer like part # EQ37100ET and your trailer has a tongue weight of 810 lbs this would be an ideal setup. Now realistically your tongue weight is going to be a bit more once the trailer is loaded so swapping to 1,200 lb spring bars like part # EQ90-01-1299 would be the best overall solution.
  view full answer...
• Weight Distribution Hitch for 2018 Coleman 263 BH Tandem Axle Travel Trailer GVWR 7600-lbs
  The specs I found for the 2018 Dutchmen Coleman Lantern 263BH tandem axle travel trailer indicate a dry weight of 5871-lbs and a payload capacity of 1729-lbs. Added together these become the GVWR for the trailer, the gross vehicle weight rating, the most it can weigh when fully loaded and ready for the road. In this case that GVWR is 7600-lbs. The rule of thumb is that a trailer must have tongue weight (TW) of 10 to 15-percent of the trailer's gross weight. I would suggest to try to stay...
  view full answer...
  
• Correct Equal-i-zer Weight Distribution System for Forest River Rockwood Ultra Lite 2614BS
  The Forest River Rockwood Ultra Lite 2614BS has a hitch weight of 800 lbs dry so you'll likely be near or past 1,000 lbs while loaded which makes the Equal-i-zer Weight Distribution System part # EQ37100ET on the edge of what it's rated for as you said. If I were you, I'd probably upgrade to a higher capacity but you don't need a new entire system for this, just the parts below: Replacement Head part # EQ90-02-1200 Replacement Spring Bars part # EQ90-01-1299
  view full answer...
• Adding Spring Bars for Lower Capacity Tongue Weight on a Weight Distribution System
  The Equal-i-zer Weight Distribution System w/ 4-Point Sway Control - 14,000 lbs GTW, 1,400 lbs TW item # EQ37140ET will still work for you but it is going to be an extremely rough and stiff ride. That system is way overrated for your 7,500 lbs maximum weight trailer. Even at the high end of your tongue weight you would still be almost 300 lbs below that systems tongue weight capacity. I recommend purchasing the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2...
  view full answer...
• How To Upgrade from Equal-i-zer 10K to 12K Weight Distribution System
  The head assembly and spring bars are different on the Equal-i-zer 12K when compared to the Equal-i-zer 10K so you will need both the Head part # EQ90-02-1200 and Spring Bars part # EQ90-01-1299 to upgrade capacity. The rest is the same so you can reuse the other parts.
  view full answer...
• Do 1,200 lbs Equal-i-zer Spring Bars Fit in a 1,400 lbs Equal-i-zer Head?
  I have a solution for you but the spring bars are a slightly different size, so in order to go from 1,400 lbs spring bars to the 1,200 lbs Spring Bars for Equal-i-zer item # EQ90-01-1299 you would also need to get a new head unit. You will want the 1,200 lb Replacement Head for Equal-i-zer Weight Distribution Systems item # EQ90-02-1200.
  view full answer...
• Replacement Hitch Head For Equal-i-zer Weight Distribution 1,000LB/10,000LB System
  If you move up to the 1,200LB Equal-i-zer Hitch Head # EQ90-02-1200 you will need to use the larger 1,200lb weight distribution Spring Bars # EQ90-01-1299 with the hitch as they use larger spring bars. To use your current spring bars you will need the 1,000LB Equal-i-zer Hitch Head # EQ90-02-1000.
  view full answer...
  
• Can You Switch Between 10K and 12K Equal-i-zer Weight Distribution Systems
  The 10K and 12K Equal-i-zer Weight Distribution Systems like part # EQ37100ET and part # EQ37120ET use different heads and spring bars so if you wish to switch back between the two capacities you will need both of these items which I have listed for you below. Equal-i-zer 10K Head part # EQ90-02-1000 Equal-i-zer 10K Spring Bars part # EQ90-01-1099 Equal-i-zer 12K Head part # EQ90-02-1200 Equal-i-zer 12K Spring Bars part # EQ90-01-1299
  view full answer...
• Can 1,200 lb Equalizer Spring Bars Replace 1,000 lb Spring Bars
  Since the 1,200 Equal-i-Zer spring bars # EQ90-01-1299 are wider at 1-1/2 inches than the 1,000 lb bars which are 1-3/8 inch you'd have to swap heads too. So with that you'd need the part # EQ90-02-1200 too to be able to convert from 1,000 lb tongue weight to 1,200 lb.
  view full answer...
  
• Can Fastway e2 Sway-Control Brackets Be Used with Equal-i-zer Spring Bars
  I reached out to my contact at Equal-i-zer (and Fastway) and he said you can continue using the existing Fastway e2 lift brackets on your trailer with the new Equal-i-zer 1,200 pound Spring Bars # EQ90-01-1299 and Head # EQ90-02-1200. This is not an issue at all. The trailer frame brackets that are used for the Fastway and Equal-i-zer systems aren't identical, but they are interchangeable between the two systems in terms of function. There's no need to swap your current brackets with...
  view full answer...
• Are Equal-i-zer Spring Bars Interchangeable With Same Head Unit?
  It is possible for some spring bars to be interchanged based on their size, but that won't increase a weight distribution system's capacity without adding the appropriate head unit. The replacement spring bars that are rated for 1,200 lbs TW and 1,400 lbs TW have the same dimensions, but the spring bars rated for 400 lbs TW, 600 lbs TW and 1,000 lbs TW are different, as you can see below. Replacement Spring Bars for 400 lbs TW, # EQ90-01-0499: 35-1/2 inches x 1-inch Replacement Spring...
  view full answer...
• Recommendation for Pulling Heavier Trailer with Under-Rated Weight Distribution System
  It sounds like you have the Equal-i-zer Weight Distribution System # EQ37060ET, which has a tongue weight capacity of 200 to 600 pounds. This will be quite a bit under-rated for your new trailer that has a tongue weight of around 1,000 pounds. I am not sure if this tongue weight is with the trailer fully loaded or empty. If this reading is with the trailer empty, this number will increase even further once the trailer is loaded and ready for a trip. I definitely recommend upgrading your...
  view full answer...
• Weight Of The Equal-i-zer Weight Distribution Hitch Spring Bars
  The Replacement Spring Bars for Equal-i-zer Weight Distribution Systems # EQ90-01-1299 weigh approximately 22lbs each.
  view full answer...
• Will Higher Rated Equal-i-zer Weight Distribution Spring Bars Increase Capacity Without Head Unit
  If you have the Equal-i-zer Weight Distribution System - 10,000 lbs GTW, 1,000 lbs TW # EQ37100ET you do need to add both the spring bars and head unit in order to increase the capacity of your system. So to upgrade to 1,200 lbs you would need to add both the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,200 lbs TW # EQ90-01-1299 and Replacement Head for Equal-i-zer Weight Distribution Systems - 1,200 lbs TW # EQ90-02-1200. To upgrade to a 1,400 system...
  view full answer...
• Can Equal-i-zer Weight Distribution be Upgraded to 1,200 lb Spring Bars
  To upgrade to a higher spring bar rating with an Equal-i-Zer system you have to replace the bars and the head since the bars are all different sizes and the heads are made to fit them specifically. So for bars you'd need the part # EQ90-01-1299 and then for the correct head part # EQ90-02-1200 and you'd be set.
  view full answer...
• Is 10K Equal-i-zer Weight Distribution Enough for a 10.7K Arctic Fox Trailer
  As long as you're able to stay within the 6-- lbs - 1,000 lbs tongue weight rating for the 10K Equal-i-zer Weight Distribution System w/ 4-Point Sway Control # EQ37100ET it will work great for your application! If you end up needing to upgrade you just need the replacement head and spring bars for the 12K system: - 12K Head Unit # EQ90-02-1200 - 12K Spring Arms # EQ90-01-1299
  view full answer...
• Upgrading 1,000 Pound Equal-i-zer WD System to 1,200 Pound Rating
  The spring bars aren't interchangeable on the higher-rated Equal-i-zer WD systems, but you'll still be able to use components from your existing setup when making this upgrade. To increase your system to the 1,200/12,000 pound capacity, you will just need the 1,200 pound Spring Bars # EQ90-01-1299 and a new WD head, part # EQ90-02-1200. The remaining hardware from your current system (L-brackets on the frame, adjustable shank, etc) can all still be used.
  view full answer...
• Upgrading to 1,200 Pound Weight Distribution Spring Bars for 7,725 Pound Trailer
  The dry hitch weight is the weight with the trailer empty of everything including propane and any other cargo, water, and other items. The gross weight of your 2017 Grey Wolf 26DBH is 7,725 pounds. That is the maximum the trailer can weigh when loaded and ready to tow. The empty weight is 5,795 pounds. So is 725 is the dry hitch weight then that is 12.5 percent of the gross trailer weight. That means that when loaded to the max 7,725 pounds the tongue weight would be around 965 pounds....
  view full answer...
• When Switching Weight Distribution Spring Bar Rating Is New Setup Required
  You'll need a new setup when going to a different spring bar since the bars would be rated totally differently. The part # EQ90-01-1299 is the correct spring bars and then for the head you'd want # EQ90-02-1200.
  view full answer...
• Recommended Higher Capacity Spring Bars And Head For Equali-zer Weight Distribution System
  Yes. To upgrade your 600 lb Equal-i-zer weight distribution system to a higher capacity, you will need to replace your spring bars, but also the head. I recommend the Replacement Spring Bars for Equal-i-zer Weight Distribution Systems - Qty 2 - 1,200 lbs TW # EQ90-01-1299 for this application along with the Replacement Head for Equal-i-zer Weight Distribution Systems - 1,200 lbs TW # EQ90-02-1200. It is an easy change out of your spring bars and head and you won't need to buy an entirely...
  view full answer...
• Parts Needed to Upgrade Equal-i-Zer Weight Distribution to 1,200 lb Tongue Weight
  We do have the Equal-i-zer 1,200 lb tongue weight spring bars with the part # EQ90-01-1299 which it sounds like you are in need of. You should note that you'll have to replace the head of the system too since they are all different sizes based on spring bars that are installed. For that you'd need the part # EQ90-02-1200. The Reese bars would not work for you.
  view full answer...
• Upgrading the Equal-i-zer Weight Distribution System
  Yes, you are correct in that you will need to upgrade your spring bars if you have exceeded the tongue weight capacity of your weight distribution system. However, the Replacement 1,000 Lb. Spring Bars for Equal-i-zer Weight Distribution Systems part # EQ90-01-1099 are 1-3/8" wide and the the Replacement 1,200 Lb. Spring Bars for Equal-i-zer Weight Distribution Systems are 1-1/2" wide. Therefore in order to upgrade the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control part...
  view full answer...
• Can 1,000 lb Spring Bar Weight Distribution System be Upgraded to 1,200 lb
  Since the fender to ground dimensions are all level at 37 inches for all four fenders it sounds like you set up everything correctly. Now I noticed you said "no difference" is that because you aren't seeing a difference in sway reduction? If so, you should note that WD systems aren't really designed to prevent persistent sway. Is your loaded tongue weight 1,000 lbs or is it more than that? Is your system the part # EQ37100ET? If so this sytem is rated for up to 1,000 lb tongue weight max....
  view full answer...
• Parts to Convert Fastway e2 to Equal-i-zer Trunnion Bar Weight Distribution
  It sounds like you have the Fastway e2 round bar 10K weight distribution system # FA94-00-1061. You can keep and re-use several parts of your Fastway system, the shank, the hitch ball and the lift brackets on the trailer. You will need a new head assembly # EQ90-02-1200, spring bars # EQ90-01-1299 and 2 of the pin/clip # EQ95-01-9400 since the Equal-i-zer systems like the 1200-lb # EQ37120ET use trunnion type bars, not round bars like the Fastway. This Equal-i-zer system works for loaded...
  view full answer...

Do you have a question about this Accessories and Part?