Arrives before Christmas To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
You can install this retractable, hard tonneau cover on your Ford Ranger in about 10 minutes, and you can completely remove it just as quickly for full bed access. Aluminum and vinyl deck has strength of a hard cover and seamless look of a soft cover.
Features:
Specs:
The Switchblade retractable hard tonneau cover provides you with security and weather protection for your truck bed, easy accessibility to your cargo, and the flexibility to haul large items that require full bed capacity whenever needed. You can install the cover without assistance in approximately 10 minutes, and you can completely remove it from your vehicle's bed just as quickly. The tonneau deck is constructed of a vinyl fabric top sheet that is bonded to rigid aluminum panels, combining the seamless appearance of a soft cover with the security features of a hard cover.
Simple, 1-Person Installation
To install the cover, set the canister on the bulkhead of your truck. Make sure that it's square with your bed. Bolt the side rails to the tabs on the canister.
Secure the rails to your truck bed side rails using 2 clamps per side. Slide the clamp onto the rail, flip the pivot arm up so it is under the bed rail lip, and tighten the clamp in place with the twist knob. Shims are included for trucks with tapered beds.
Each clamp at the tailgate end of the rails has a supplemental kickstand to help level the rails and prevent overtightening during installation. To install the kickstand, simply slide it into the grip handle at the bottom of the clamp. Rotate the kickstand so the foot rests squarely against the side wall of the truck bed, and tighten in place.
Mount the top cover plate to the canister with the included hardware. Attach the drain tubes to the canister and route each tube out of the OEM drain holes in the floor of your bed.
To hold the pull strap off the floor of your truck bed, apply the adhesive hook-and-loop fastener strip onto the underside of a rail at your desired location.
Remove or Reinstall in 10 Minutes
After the initial installation, the tonneau cover can be completely removed or reinstalled in approximately 10 minutes. The Switchblade is great for whenever you need to haul large items that require full bed capacity from front to back and side to side. After your large haul is complete, you can easily reinstall the cover to protect your truck bed again.
To utilize your entire truck bed, detach the canister from the side rails by removing the bolts on either side with a wrench. Then take the side rails off your truck by removing the clamps with the same wrench. Wrap the pull-strap around the canister and use it to lift the canister off your vehicle.
Retractable Cover with Built-In Pull Strap
To retract the Switchblade, simply squeeze the pinch grips located underneath the cover near the center of the tailgate to activate a heavy-duty tension spring. The spring automatically retracts the cover into the canister at the bulkhead of your truck bed. This provides quicker, easier access to your truck bed when compared with manual retractable covers that have no spring-loaded assist.
A built-in pull strap helps you extend the cover over your bed. As you pull, the tonneau will glide smoothly along tracks in the side rails until it reaches the tailgate and secures in place. You can also use the rear plate of the tonneau cover to pull it closed.
Compact, Angled Canister
The cover retracts into a canister located at the front of your truck bed, giving you unrestricted visibility out of your rear window. The canister also protects the stored cover from the elements. And the compact, angled design allows for maximum clearance for your tools and cargo.
Water Management System
The Switchblade rails feature a water management system that channels excess water into the canister. This prevents water from getting into your bed or freezing in your tonneau cover rails during cold temperatures. Drain tubes attached to the bottom of the canister remove water through the OE drain holes in the floor of your truck bed.
Flush-Mount Design
The black powder-coated side rails sit 1/8" above your truck bed rails for a flush appearance. This low-profile design is aerodynamic to reduce wind drag, and it helps to improve gas mileage when the cover is closed.
Stylish and Heavy-Duty Construction
The Switchblade deck is constructed of a vinyl top layer bonded to heavy-duty aluminum slats. This ArmorTek deck looks like a soft tonneau cover with no visible seams, but has the strength and security of a hard tonneau cover. A large seal at the rear of the bed closes the gap between the cover and tailgate to create a barrier to prevent water from entering the truck bed.
Security
The Switchblade provides excellent protection for your cargo when used in conjunction with a closed and locked tailgate. Both the pinch grips and pull strap are located underneath the rear plate, which makes them inaccessible when your truck bed is closed. The heavy-gauge aluminum panels are better at preventing theft when compared with soft covers that can be cut or punctured with a knife. The panels are also more effective at preventing theft than tri-fold hard tonneau covers because the panels cannot be pried open at any point along the rails.
California residents: click here
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.