BAK Industries Tonneau Cover - BAK42VR

Weather-resistant, roll-up cover keeps the gear in your truck bed secure and dry. Rolls up quickly by hand for full access to your truck bed. Aluminum slats keep cover tight and help prevent break in. Requires no drilling to install.

Features:

• Roll-up, soft tonneau cover keeps the gear in your truck bed secure and dry
• Cover rolls up for full truck bed access - secures with hook-and-loop straps and buckles
• Pinch levers let you easily open cover from either side of truck bed
  • Cover latches shut whether tailgate is open or closed
  • Tailgate lock keeps your gear secure
• Low-profile cover with textured, matte black finish sits 1-1/2" above the bed rails
• Double-coated, reinforced vinyl with aluminum bows is sturdy and resists tears
  • Self-tensioning frame keeps the cover taught
• Weather seals keep out water without need for drain tubes
  • Beveled edges direct water off the sides of cover
• Easy, clamp-on installation inside truck bed rails - no tools or drilling required
• Limited lifetime warranty

Specs:

• Weight capacity: 400 lbs evenly distributed
• Limited 5-year warranty

Get the advantages of both a hard tonneau cover and a soft tonneau cover for your vehicle with the Revolver X4s. This hybrid tonneau likely has an identity crisis. It's built like a hard cover, but it looks and acts like a soft cover. With the Revolver X4s, you get the strength, durability, and security of a hard tonneau and the sleek look and convenience of a soft, roll-up tonneau - all while protecting your truck bed and cargo and helping to improve your fuel mileage.

The X4s has the features of the original Revolver X4 with upgrades including a matte black aluminum underbody, integrated safety slat caps, rear corner caps, and an integrated bulkhead seal.

Strong, Convenient Hybrid Design

The secret to the Revolver X4s's versatility is the aluminum slats on the underside of the cover that make it strong, seamless, and flexible. These individual, hinged slats give the cover its rugged body, while also allowing enough flexibility for the cover to be rolled up. Atop the slats is a tough, 1-piece vinyl layer that adds to the tonneau's sleek look and overall durability while also keeping the slats perfectly aligned. As a result, the Revolver X4s will roll up evenly every time, unlike ordinary soft vinyl covers that can get lopsided as you maneuver them.

Low-Profile Appearance

Unlike other tonneau covers that sit 1/2" or more above your truck bed rails, the Revolver X4s sits nearly flush with your rails for a clean, ultra-sleek look.

Full Truck Bed Access

The Revolver X4s gives you full use of your truck bed in a matter of seconds - just roll up the cover and secure it behind the cab. As a result, you can tote around all your gear without having to remove the tonneau. And because the Revolver X4s mounts inside your truck bed rails, you can still use your truck bed stake pockets to mount accessories like tie-down anchors.

Simple, One-Person Operation

The Revolver X4s is simple to operate. Following installation, just roll the cover out and press down on the rearmost slat at the tailgate to secure the tonneau in place. The built-in latches not only lock down the back end of the tonneau, but they also fasten the sides of the Revolver X4s along the length of the frame rails. The rail tooth runs the entire length of each frame rail. It rotates downward to lock the side rail into the sides of the cover.

When the cover is rolled out and the rear slat is pressed down at the tailgate, the latches on both sides engage. When this happens, the integrated teeth pivot down and rest on top of each slat of the rolled-out cover. Closing the rear slat effectively pins the cover to the rails, ensuring that the cover stays closed from front to back. It's that simple - no Velcro to seal or snaps to wrestle with. When your tailgate is closed and locked, no one will be able to get through the cover, thereby safeguarding your truck bed and its contents. The cover automatically secures as the locking levers at the tailgate engage. These sturdy levers have reinforced gussets that give them added strength and durability. And they will never need adjustment.

To roll up the cover, unlatch the rear slat by dropping the tailgate and pulling either of the 2 release cords located along the bottom corners of the slat's housing. Either cord will release both of the latches so that you can raise the rear slat. When the latches are disengaged, the teeth roll back into the frame rails, releasing the sides of the cover so that you can easily roll it up. Just fold the rear slat over and roll up the cover the rest of the way.

Then secure the tonneau behind the cab with built-in nylon straps and sturdy plastic buckles. These straps help to keep the bundled tonneau from contacting your cab while you drive. And 4 rubber bumpers act as cushioned barriers between the cover and your truck cab.

Heavy-Duty Construction

The Revolver X4s's rugged aluminum and vinyl construction makes it an ideal match for your truck, no matter what you do while at work or play. This cover is strong enough to hold up to 400 lbs of evenly distributed weight when it's rolled out. The 1/4" thick, aircraft-grade aluminum slats are covered with a matte black vinyl skin for superior resistance to impacts, UV rays, and weather. This skin is what gives the tonneau its soft, sleek look. While the Revolver X4s may look like a soft cover, its aluminum skeleton provides exceptional security because it cannot be cut through in the same way that a standard soft vinyl cover can be.

Felt strips on the underside of the tonneau help to keep the slats from scuffing the vinyl top as you roll up the cover. The soft felt also shields your hands when the cover has gotten hot or cold. And rubber strips overlay your truck's side rails, cab rail, and tailgate, creating a seal that helps to conceal any gaps and works to prevent water from seeping in.

Easy, No-Drill Installation

Installing the Revolver X4s is simple. All you need is a wrench, and you don't have to do any drilling. The tonneau's frame rails clamp to the inside of your truck bed side rails to create a base for the cover. The included bolts secure the front hinge rail to the frame rails at the cab.

Slotted brackets at the ends of the tonneau side rails allow the bolts to shift in case you need to adjust the cover to achieve a snug fit. These brackets ensure proper alignment of the tonneau frame on your truck bed side rails. This eliminates trial and error in installing your rails - you won't have to put them on and then take them off again to get the correct fit. Pre-installed shims and spacers also help to ensure that the Revolver X4s rails are installed squarely on your truck bed.

80126 BAK Revolver X4s Hard Tonneau Cover - Roll Up - Aluminum and Vinyl - Matte Black

Installation Details 

This Product Fits The Following Vehicles

• 2015 - 2022 GMC Canyon 5 Foot Bed
• 2015 - 2022 Chevrolet Colorado 5 Foot Bed