Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This 1" round amber LED light shines bright while keeping power draw low. Running on 12V DC and pulling just 0.03 – 0.06 amps, it’s built for high visibility without stressing your electrical system. The single premium diode is rated for up to 100,000 hours of operation and resists vibration, so you won’t be swapping bulbs or dealing with flicker any time soon.
For trailers that see water, this light is built to handle it. The lens and housing are sealed together as one unit, keeping moisture out and protecting the circuit board from corrosion. It’s IP68-rated for dust and water protection, and the TecSeal urethane potting offers better sealing than common epoxy. Whether you’re towing in the rain or backing into the water, your light stays dry and reliable.
A PC-rated beam pattern means this light throws a full 180-degree arc of amber light for clear visibility from the front and sides. Mounted at a 45-degree angle, it works as both a clearance light and a side marker, so you get two functions in one compact setup. That extra coverage helps make your trailer more visible at night or in low-light conditions, keeping you safer on the road.
At just 1" in diameter and 7/8" thick, this light tucks neatly into small spaces. It installs through a standard 3/4" cutout using the included grommet for a clean recessed fit. The 12" pigtail with 0.180" bullet connectors plugs right into matching trailer wiring—no fussing with adapters or extra parts.
The impact-resistant polycarbonate housing and UV-resistant lens stand up to weather and sun exposure without fading or cracking. Designed with military-grade construction around the circuit board, this light holds up under rough use while maintaining consistent brightness trip after trip.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi everybody, Andy here with etrailer.com. Let's take a look at this submersible Amber LED mini clearance or side marker trailer light. Now with this little one inch round waterproof LED mini trailer light, you're gonna be able to haul safer by alerting other drivers of your trailer's position and direction of travel. This light functions is both a clearance and a side marker light when properly mounted. And as you can see, this is really bright even with my studio lights on here. But just to give you a better demonstration of its effectiveness, let me go ahead and turn my studio lights off here, and you get a better demonstration of the brightness and the light that it gives.
I'm gonna zoom out here and then just shine this on the wall behind me. So this one Amber LED underneath this amber lens is rated for up to 100,000 hours of operation. It's energy efficient, long lasting and vibration resistant. This is a PC rated light meaning it produces a 90 degree angle of light on either side of its center line for a total of 180 degrees of coverage. This beam pattern can be clearly seen when you are standing directly in front of the light, as well as when you are standing on either side of the light.
Rather than buying a side marker and clearance light separately, you can mount this single PC rated light at a 45 degree angle on the corner of your trailer to act as both. Now this sealed waterproof light includes a durable polycarbonate housing and a UV resistant lens. The circuit board is of a military grade construction, and the urethane potting is gonna give you better protection than the common epoxy potting. This has an IP rating of 68, and this is 12 volt DC compatible. As you can see, it's a two wire pigtail with 0.180 male bullet ends.
And that wire length, I'm gonna go ahead and pull my ruler out here and just confirm that with you. I'm gonna line this up so you can see that. So from behind the light all the way to the end here, we're sitting at about 11 1/2 inches long on that wire length. And this is a recess mount installation and it has a grommet included with this as you can see. And the installation does require a three quarter of an inch in diameter cutout.
And this light is about 7/8 of an inch thick. Now on this product page, we do have a diagram with some additional measurements that I did not cover with you today. So if you are in need of some other measurements, you can find those on this product page with the diagram. This does meet or exceed FMVSS 108 standards. And this does have a limited lifetime warranty. Well, that's gonna conclude our brief look today. I do hope that it was helpful for you. Again, my name is Andy. Thank you for joining me.
Ratings & Reviews
Great service and light exceeded my exp ectations
a fun little project, I put new tail lights on my trailer and found out I had one bad wire , so I pulled new wires and added these onto my Roller guides , look really nice!
When I first installed it, it seemed to be dull but it was because I didn’t have a good ground.
Excellent product I will recommend to friend , excellent communication with buyer
Thank you guys !
Perfect fit to replace one that was damaged on our trailer.
They are great just what i was looking for super Brite and easy install
Great replacement light however the wiring is reversed from the lamps on my unit.
These lights were exactly what I needed and replaced some broken ones on a trailer fender. Good quality and were as advertised.
Great clearance lights for my new ebike rack!!
More info on size of marker lights. Was replace 3/4 lights on a Tritons snowmobile trailer with clam shell on it. They work just not as bright as old lights.
Product itself is great. I'm not familiar with trailer wiring, so if there is a standard wire gauge that is typically used that's on me for not knowing it, but it would be nice if it were included in the product description. Aside from that, I am extremely satisfied with my item.
Plug and play just like OEM! Great product and price!
These clearance lights are an exact replacement for those on my Wells Cargo trailer, whose grommets had rotted from exposure to the sun. Etrailer's list of their product's specifications made it easy for me to order the correct part. Shipment was immediate. I'm a happy repeat etrailer customer!
Nice
Great quality lights,,, will be putting them on the trailer tomorrow.
Excellent thank you
Nice and bright
Easy installation
Matched the bulbs in my shoreland’r trailer perfectly, the plugs were a different size. I just heat shrink soldered the new one on. Probably a better connection anyway. No problem
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Mike L.
4/30/2026
We're glad to hear that, good job!