To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
A lot of covers make you pick between strength and flexibility, but this one gives you both. The TruXedo Sentry CT combines 3/4" thick aluminum slats with a premium 5-layer polyester and vinyl fabric for a tough, impact-resistant surface that still rolls up easily. The aluminum keeps your cargo safe from hail and falling debris, while the woven top layer resists UV rays, dirt, and moisture. It’s built to handle extreme temperatures from -40°F to 120°F and holds up to 400 lbs of evenly distributed weight.

When you need the whole bed, you don’t have to remove the cover. Just pull one of the release cables at the tailgate and roll it up toward the cab. Safety straps keep it secured and out of the way, leaving your rear window and third brake light clear. You can also remove the cover completely without tools thanks to the quick-release guides. Whether you’re hauling lumber or camping gear, you get full-bed use without extra hassle.


The side rails are angled at 15 degrees so the cover sits just 1/2" above the bed. That gives the truck a smooth, flush look while cutting down on wind drag and noise. The blacked-out aluminum slats and matte fabric top blend together for a seamless look when rolled out or rolled up. Because the rails mount inside the bed, your stake pockets stay open for racks or tie-downs.

Keeping gear safe is simple with the Sentry CT. Slam latches at the tailgate lock the cover tight when the tailgate is closed and locked, and additional mid-bed latches automatically secure both sides so no one can pry underneath. The hard slats can’t be cut open like soft covers, giving you extra peace of mind when your truck is parked.


Installing this cover doesn’t require drilling or complicated adjustments. The bolt-on clamps mount the rails inside the bed, and the self-leveling design keeps them square so the cover rolls evenly every time. The hook-and-loop fasteners along the rails seal tight to keep out water and dust. Once installed, the setup looks clean and operates smoothly without constant tweaking.




Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews

Claire H.
6/10/2026
It looks perfect!! Thank you for the glowing review!

Kate F.
11/13/2026
Elvin, that cover looks sharp on your Ram. I can see why you like the cleaner look without the latches sticking out. Hopefully, this one gives you just as many good years as your old BAK cover did. Thanks for the pictures =)

Jenny N.
9/16/2023
There is a lot going on with the cover. Would you be able to send a picture of the cover and the serial number from it.


Bryan
8/22/2023
After a year the cover is still looking great and working great. I wish I had purchased one of these when I purchased my truck, as it is nice to be able to securely store stuff in the bed of my truck.

Gwendolyn Y.
6/18/2025
Thanks for sharing your honest feedback about the cover, Brian. Let us know how it holds up to the rain and the elements when you get to test it out.

Mike L.
8/27/2026
That's not good Edward! I'll get that taken care of for you.
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.









William C.
6/4/2024
After one year, the cover is still looking good and operating as expected. Very happy with the investment.