To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Rain, dust, heat, or hail—this cover is built to handle it all. The TruXedo Sentry CT uses a premium, 5-layer woven polyester and vinyl fabric bonded over 3/4" thick aluminum slats. The material has been tested to handle temperatures from -40°F to 120°F, staying flexible and tight in any season. The blacked-out finish looks clean and resists UV damage, while the hard slats protect your cargo from falling objects or anyone trying to cut through the cover.
When you need to haul tall gear or big loads, you don’t have to remove the cover. Just pull one of the release cables at the tailgate, roll it up, and secure it with the built-in safety straps. The Sentry CT rolls up evenly every time thanks to the aligned aluminum slats, and once it’s stored against the cab, it stays low enough that it won’t block your rear window or third brake light. You can even remove the entire cover in seconds without tools using the quick-release guides.
A bulky bed cover can kill the look of your truck and add drag. The Sentry CT solves that with side rails angled at 15 degrees, sitting just 1/2" above the bed for a flush, streamlined profile. This low-profile setup cuts wind noise and drag, which can help improve fuel economy. The cover’s self-leveling rails make installation simple—just tighten the clamps and the rails square themselves perfectly for a smooth, even roll every time.
Security matters when you’re carrying tools or travel gear. The Sentry CT locks down tight with dual slam latches at the tailgate and extra locking points at the mid-bed. Close the tailgate and the cover locks automatically. The hard aluminum slats prevent prying or cutting, while the rubber weather seals keep out water and dust. When it’s time to open it, just pull a release cable from either side of the bed—no crawling or reaching required.
No drilling or special tools are needed to mount this cover. The bolt-on clamps hold the rails in place inside the bed, leaving stake pockets open for racks, tie-downs, or bed rails. The hook-and-loop fasteners along the sides keep the cover sealed tight while driving. With its 400-lb evenly distributed weight capacity and 5-year warranty, the Sentry CT offers the convenience of a roll-up with the strength and look of a hard cover.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
The Sentry and Sentry CT by TruXedo are hard roll up style truck bed covers that feature an extra low profile.The Sentry comes with a leather grain vinyl fabric and the Sentry CT comes with woven matte black fabric. Both feature fabric that is pressure bonded to heavy duty aluminum slats, making Sentry the ultimate in durability and security.Each cover ships with a cover assembly, driver and passenger side rails, and all the hardware necessary to install it on your truck. The only tools necessary are a half inch wrench and scissors.Clean the bulkhead area with alcohol. Adhere the rubber seal to the bulk head, making sure to align the seal with the inside edge of the bulkhead. Trim the seal to sit flush with the bed caps.Position one side rail on the truck bed. Make sure the rail sits level on top of the truck bed.
Slide the rail towards the bulkhead so that the foam seal is compressed about half way. Install a clamp in the center of the rail, using a half inch wrench to tighten.Install the real clamp about 12 inches from the tailgate. To ensure a proper seal, put pressure on top of the rail when tightening. Install the front clamp about 12 inches from the bulkhead. Repeat on the opposite side.Place the cover assembly on the rails at the bulkhead.
Line the screw head on the underside of the cover assembly with the slot in the rail on each side.Slide the header guides towards the rail to secure the rolled cover to the rails. The header guide will click when it is securely fastened.Unroll the cover to the tailgate. Close the tailgate. Then push down on the end of the cover to latch both sides. Secure the hook and loop on both side rails before driving.To open the cover, drop the tailgate and pull down on a release cable.
Lift and roll rear header.To drive with the cover in the open position, both straps must be secured to the restraining straps. To releasee the strap, push the tab up.The installation is now complete.
Ratings & Reviews
Claire H.
6/10/2026
It looks perfect!! Thank you for the glowing review!
Jenny N.
9/16/2023
There is a lot going on with the cover. Would you be able to send a picture of the cover and the serial number from it.
Jenny N.
9/22/2023
Bryan
8/22/2023
After a year the cover is still looking great and working great. I wish I had purchased one of these when I purchased my truck, as it is nice to be able to securely store stuff in the bed of my truck.
Gwendolyn Y.
6/18/2025
Thanks for sharing your honest feedback about the cover, Brian. Let us know how it holds up to the rain and the elements when you get to test it out.
Mike L.
8/27/2026
That's not good Edward! I'll get that taken care of for you.
Info for this part was:
At etrailer we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Shannon
1/16/2021
No issues, no fading. Glad to have the strong aluminum slats after getting several foot deep snow storms on it.