Arrives before Christmas 
Mount your bike rack or cargo carrier above or below your RV bumper. Hitch receiver constricts and tightens around your RV bumper using a heavy-duty retention fastener. Clamp-style design holds your shank in place to reduce rattling and damage.
Features:
Specs:
Note: Bumper weight capacities vary by manufacturer. Please be sure to verify the weight capacity of your bumper with the manufacturer prior to loading.
The ShakeStopper gives you the flexibility to mount your hitch above or below your RV bumper. You can mount your hitch receiver below the bumper if your camper body hangs over your bumper. You can also mount it above to give your bike rack or cargo carrier an extra 6" of clearance to avoid scraping on uneven surfaces when entering or leaving parking lots or crossing roads.
No more loud, shaky rides and damage to your bike rack or cargo carrier. Unlike conventional bumper-mounted hitches that often tighten down the shank using set screws that cause instability and dents, the ShakeStopper has a unique clamping design that firmly holds your bike rack or cargo carrier in place to help reduce noisy rattling and avoid damage to your shank from rocky, bumpy rides.
The shank is held in place between a 1/4" steel base plate and the free-floating pressure plates. The heavy-duty retention bolt are used to tighten the pressure plates down, creating a clamping force to reduce movement of your hitch-mounted accessory. The base plate helps distribute the load when the pressure plates are engaged to prevent denting and other damage. Shank locks in place with a 5/8" hitch pin and clip (sold separately).
Most bumper-mounted hitches use load-bearing fasteners, such as U-bolts, to carry the weight of hitch-mounted accessories, like a bike rack or cargo carrier. The bolts can easily dent your bumper if over-tightened and tend to loosen over time, causing your hitch to bounce and shake while driving down the road, leading to more damage on your bumper. This unique design was constructed with a retention fastener to firmly clamp the side plates and base plate around your bumper to reduce the risk of damage.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody. This is Jeff at etrailer.com. Today I'm gonna take a look at this Mount-n-Lock ShakeStopper with the two-inch hitch receiver for the 5.3 inch RV bumpers, has a 400 pound weight capacity. Now this ShakeStopper bumper mount two-inch hitch receiver will let you mount your bike rack or your cargo carrier either above or below your five inch by five inch RV bumper. Just to show you what we're talking about I'm gonna pop up an insert and you can see with it either mounted above your bumper or if you flip it around you can mount it below. You can mount the hitch below the bumper if your camper body is hanging over your bumper.
And you can also mount it above to give your bike rack or cargo carrier an extra six inches of clearance to avoid scraping on uneven surfaces when you're entering or leaving a parking lot or crossing roads. Now the hitch receiver constructs and tightens around your RV bumper using a heavy duty retention fastener right here at the top. There's no drilling required. The plates and the hardware all included to install this. Comes with a nice set of instructions with pictures shows how everything installs.
It is a clamp style design. This will hold your shank in place to reduce rattling and damage to the shank. The retention bolt will tighten the pressure plates down to reduce bouncing and shaking. The base plate helps distribute the load when the two pressure plates are engaged to prevent any dents to your bumper. And it does eliminate the common failure points caused by load bearing welds or bolts.
It is a durable steel construction with a nice black coated finish to resist rust and corrosion. It is made in the USA. Few specs again, it fits five inch by five inch square RV bumpers. Overall dimension of this part itself is gonna be about 10 1/4 inches tall, 5 inches wide, and about 5 3/4 inches deep. Maximum capacity on this dimension is 400 pounds when it's evenly distributed, and the weight on this is only about nine pounds.
One note I do wanna mention, the bumper weight capacities do vary by manufacturer so you wanna be sure to verify the weight capacity of your bumper with the manufacturer prior to loading it down. But that should do it for the review on this Mount-n-Lock ShakeStopper with the two inch hitch receiver for 5.3 inch RV bumpers.
Works great for holding our motorcycle rack.
Mounted it on an 4" RV bumper per directions. I ordered this model because it was rated for well over my intended use. I installed a 45 lb rack and carried a 119lb Generator. Nothing else. I watched it very carefully. It started to collapse. Don't trust it for over 100lbs period!
very good bracket, quality built
Great customer service so helpful and willing to go the extra mile for customer!
Works perfectly! I watched the video versus reading the assembly directions and it was super easy to put together. It works great for our spare tire carrier. Great upgrade from the one we had!
I bought this "shakeStopper" about a year ago, so here is my story: My plan was to mount on the "tube" style bumper (Lance 2285) so I could install a bike rack to hold two E-bikes. A "black widow" rack (75#) and (one E-bike 45# after the batteries removed) so approx 170#. Madden voyage of 300 miles and the "tube" bumper failed at the welds due to the weight. The Shake Stopper saved the rack and bikes from being a total loss. The Shake Stopper is stout/heavy duty and easy to install. Just a reminder that most "tube" bumpers are not designed to support much weight, so use discretion on what you use it for. Wound up buying a new class III bumper from etrailer and its is amazing... etrailer is my go to for trailer parts. So I rated the Shake Stopper as 5 star for the quality and design! My tube bumper failure was no fault of etrailer.
Solid high quality metal. Clever design and engineering. Good instructions with photos.
This works so great! We had an unusual bumper size and were in a pinch and confused and their excellent customer service taught us stuff and walked us through the process. SERIOUSLY great customer service and it matches their excellent products!
works perfectly
Great for bike rack no movement easy to install
Worked perfect for the 5" MountnLock aluminum bumper. Heavy duty.
I had to deepen the notch on the two small plates approximately 1/8”, so the 2” tubing could enter the receiver.
I ordered for a 5” rv bumper. As advertised! This actually fits a 5.3” bumper. My bumper measures exactly 5” outside.
E trailer always great to work with!
Awesome Product. Sturdy and safe.
Do you have a question about this RV and Camper Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.