See what our Experts say about this Brophy Camper Jacks

• What Size Cable do I use to Replace the Cable On My Brophy Camper Jacks?
  Hello Michael, Great question. I reached out to my contact at Brophy and they use a 3/16 aircraft cable 113" long. I am in the process of getting the replacement cable added to our site. I will let you know when it is available for purchase in case you can't find it locally.
  view full answer...
• Are The Brophy Cable Camper Jacks Stable
  You should not have a problem with the camper sliding out when you are using any of the Brophy Cable Camper Jacks. The jack is very stable because of the tripod base. That stability will make the jack very difficult to tip to the front or the back. You will need to use two jacks, one per side. You will just need to make sure your camper jacks maximum weight capacity exceeds the weight of your camper. I have included a the different model Brophy Cable Camping jacks and their weight limits...
  view full answer...
• What Is The Difference Between Brophy Cable Camper Jacks CJ31 and CJ41?
  I would be happy to help! The only difference between the Brophy Cable Camper Jacks # CJ31 and # CJ41 is the weight capacity. The # CJ31 has a 1000lb weight capacity where the # CJ41 has a 3000lb capacity. Both have the same 17" - 57" lift range, so you will just need to pick the one rated high enough for the weight of your truck bed camper/cargo box. I included videos of the products mentioned for you to take a look at.
  view full answer...
  
• Replacement for Older Happijac Truck Bed Camper Jack
  Thanks for the photo and that model of Happijac is nearing a quarter-century old as of this writing and there are no longer replacement parts available for it. The best option we can offer are new camper jacks, the Brophy Cable Camper Jacks and you will select the right one based on the weight capacity and maximum lift height you need. - 1,000 lbs: Brophy Cable Camper Jacks - 57" Max Lift Height # CJ31 - 1,500 lbs: Brophy Cable Camper Jack - 67" Max Lift Height # CJ74H - 3,000 lbs: Brophy...
  view full answer...
  
• Diameter of Tripod Base for Brophy Cable Camper Jacks
  I measured the inside diameter of the Replacement Tripod Base for Brophy Cable Camper Jacks # 1106 and found it was 2 inches. This base is a replacement for the Brophy Cable Camper Jacks - 57" Max Lift Height # CJ41 and 67" Max Lift Height # CJ74.
  view full answer...
• Homemade Slide In Camper Lift Recommendations
  For your horizontal clearance this will really come down to your specific truck as well. The Brophy Cable Camper Jacks have an offset lifting point that is designed to even with the legs of the jacks themselves. So if your truck has fenders that may bulge as it approaches the wheel wells, or your tires are wider than the outer fenders this would cause them to contact the stand and would not work. I personally would want to see at least 4" from the widest point to ensure enough clearance....
  view full answer...
• Recommended Camper Jacks For A 2004 Sunlite Eagle SB On A 2018 Ford F-150
  With your Sunlite Eagle weighing 1,050 pounds, I recommend the Brophy Cable Camper Jack # CJ41.Using these jacks have a combined weight capacity of 3,000 pounds and you will have no issues lifting up your 2004 Sunlite Eagle SB. The Brophy Lifting Jacks have a lifting range between 17 inches to 57 inches and have an overall height when assembled of 63 inches. When using these jacks always make sure that the jacks in pairs on level ground. If you have any further questions please feel free...
  view full answer...
• Can Brophy Cable Camper Jacks Work if Camper Only Extends Out 1 inch
  The lift brackets of the Brophy Tripod Camper jacks part # CJ41 extend out from the upright mast the same distance as the feet of the tripods. So as long as the camper extends out past the tires like you said yours did this would work although clearances would be pretty tight for you since it's only 1 inch.
  view full answer...
• Winch to Lift Top of Pop-Up Camper Whose Cables Broke
  Brophy Cable Camper Jacks # CJ41 are designed for truck bed campers and for truck toppers and camper shells but for your pop-up camper whose cables have broken the safer way to raise it up is a lifting winch like the Pro Series Standard Brake Winch # PSKR15000301 which works with 25-foot cable # DL24047. This winch has an automatic brake that engages as soon as you let go of the cranking handle. It cannot free-wheel which means it will be very safe in your application.
  view full answer...
• Jack Needed to Support Slide Out on 2018 Passport 2810BH with No Rails Under Slide Out
  Since you don't have the rails under your slide out the typical slide out supports like part # UF19-960003 wont' work but we do have another possible solution for you. Brophy has some camper jacks that are meant to be used for supporting a truck bed camper but when I spoke with my contact at Brophy she said you could use them for your slide out too. These come in varying weight capacities and max heights so you would just need to choose one that fits your application. Please note that...
  view full answer...
• Jacks to Lift a Truck Bed Camper Out of a Ford Ranger
  There are actually special jacks for truck bed campers like yours. We carry some manual camper jacks, # CJ41, rated for 3,000 pounds. They have a 57 inch maximum lift height. It is recommended that 2 people operate the jacks simultaneously to make it easier to raise each side of the camper evenly. However, 1 person can do the job by alternately lifting or lowering each jack in small increments. Landing gear types of jacks such as # UF17-943010 are for 5th wheel trailers and would not have...
  view full answer...
• Brophy Truck Bed Camper Jacks Compatibility with Dually Truck
  The Brophy Cable Camper Jacks - 57" Max Lift Height - 3,000 lbs - Qty 2 # CJ41 would require two sets of jacks to lift your 4,500 lb truck bed camper and that application will absolutely work. The issue is the dually rear axle will cause that fender to stick out and that is problematic for these jacks. I reached out to the manufacturer and they can't confirm the fit of your Arctic Fox 1150 and Ram dually truck with this system. The poles are very close to the bed rails and the compatibility...
  view full answer...
• What Does the Brophy Cable Camper Jacks # CJ41 Weigh
  Each of the jack assemblies that comes with the Brophy Cable Camper Jacks # CJ41 weigh 43 lbs.
  view full answer...
• Recommended Truck Bed Camper Jacks for a 1996 Northern Lite Camper
  The only truck bed camper jacks we offer are the Brophy Cable Camper Jacks. As long as the loaded weight of your truck bed camper does not exceed 3,000 lbs then I recommend part # CJ41 for 57" of lift or part # CJ74 for 67" of lift. These jacks will do an excellent job of helping to load and unload your camper into the truck bed. They do not permanently install on the camper which makes for a very clean look and they can also be broken down into three pieces for easy storage.
  view full answer...
• Recommended Stabilizers for RV Patios
  The only supports we have for a patio or slide out are the slide out supports like the Ultra-Fab # UF19-960001 or # UF19-960002 if there is a frame rail. You could alternatively use a scissor stabilizer jack like # TJSC-24 or # JSC-30-IND. The only other option I can think of is to use the Brophy Cable Camper Jacks - 57" Max Lift Height - 3,000 lbs - Qty 2 # CJ41 as a stabilizer. The Ultra-Fab Stackable Stabilizers for Small Trailers and Campers - 6,000 lbs - Qty 4 # UF48-979004 would...
  view full answer...
• Dimensions Of Replacement Handle for Brophy Cable Camper Jack
  The Replacement Handle for Brophy Cable Camper Jack part # 1007 is 1/2" long by 3/8" wide. The overall length of the handle is 9-1/4" long and the straight portion of the handle is 6-3/4". It is designed to replace the Brophy cable camper jacks part # CJ31 part # CJ41 and part # CJ74. However, I have attached a diagram for you to compare this handle to your handle. This is the only camper jack handle that we carry that is this design.
  view full answer...
  
• Does the Brophy Cable Camper Jacks Come With the Upright Posts
  Yes, I cannot speak for our competitors but I can assure you that the Brophy Cable Camper Jacks part # CJ41 do come with the upright poles and all of the other parts you will need to lift your truck bed camper on and off your truck. The components that you see in the attached photo are all included.
  view full answer...
  
• Gauge of Replacement Poles for Brophy Cable Camper Jacks
  Hi Marco; I reached out to Brophy and the Replacement Poles for Brophy Cable Camper Jacks # CJ41-1101 are 16 gauge. Did you have an issue with one of the poles on your # CJ41?
  view full answer...
• Is The Up And Down Lever A Replaceable Part For The Brophy Cable Camper Jacks
  Unfortunately the only way to get the up and down lever for your Brophy Cable Camper Jacks # CJ41 you're referring to would be to replace the entire winch with part # W14Z.
  view full answer...

Do you have a question about this Camper Jack?