Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
(216 reviews)
Price: $204.45
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
Item # HSSF
Retail:$217.14
Our Price: $204.45
You Save: $12.69
This item qualifies for Free Shipping
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (216)
- Q & A (0)
- Photos
- Used (2)
Brophy Camper Tie-Downs - HSSF
- Front and Rear Tie-Downs
- Brophy
- Bed-Mounted
- Powder Coated Steel
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.
Features:
- Creates attachment points for securing your camper to your truck bed
- Wide clamps provide superior holding strength
- Turnbuckles (sold separately) required to attach camper to tie-downs
- Protects your truck's paint with neoprene pads attached to the brackets
- Resists corrosion and rust with black powder coated steel
- Clamps securely onto your bed rails - no drilling required
- Includes 4 camper tie-downs with clamp plates, 12 neoprene pads, and installation hardware
- Made in the USA
Specs:
- Application: for exact fits, enter in your vehicle's year/make/model above
- Minimum 2" needed between sidewall and lip of bed rail
- Not compatible with drop-in bed liners, aftermarket bed rails, double-walled beds, or side-step beds
- Dimensions: see diagrams below
- 1-Year limited warranty
No-Drill Installation
These clamp-on tie-downs install quickly and easily, with no drilling or modification to your truck required. Because they're mounted in the bed instead of on the frame or body of your truck, you don't need any kind of fancy mechanical background to get this job done. You just need to slide the hold downs over the rails of your truck and clamp them down with the included T-bars and hex bolts.
The fact that they simply clamp on means that you can remove these tie-downs when you're not hauling your camper, leaving no trace. Use the provided neoprene pads on the T-bolts and tie-downs where they make contact with your truck to make sure no scratches or dents will be left behind either.
It's important that the tie-downs on your truck line up with the anchors on your camper at the correct angle to ensure a secure hold. Ideally the tie-downs should be on the outside of your camper's anchor points, but they can be on the inside as well, just as long as they're not lined up with each other.
Securing your Camper
To secure your camper to your truck, you'll also need a tie-down hardware package consisting of turnbuckles, S-hooks, and chains (TDHP - sold separately). This hardware attaches the anchors on your camper to the tie-downs on your truck to keep your camper safely mounted. Once you tighten the turnbuckles to the correct level of tension (not too tight!), you'll be good to hit the road.
HSSF CR Brophy Truck Camper Tie Downs for Slide In Truck Camper - Camper Hold Down - No Drill Tie Down - 4 Pack
Installation Details
Customer Satisfaction Score:
91% were satisfied with this product
9% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4 - HSSF
Average Customer Rating: 4.6 out of 5 stars (216 Customer Reviews)
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.by: TheAvionNomad01/18/2024
I used these to mount a vintage 1970 Avion C-11 to a 1993 D250. They worked great and were much stronger than I expected - and it was a huge cost savings (and a much more attractive look) than some of the frame mounted options of more than $1000. There were some oddities that I noticed. It was impossible to mount them exactly the way the instructions suggested because of where on the wings near the cab,. The brackets also could not stay on with the camper unloaded because they would hit the jack mounts, meaning they had to me bolted in after the camper was in the truck but before lowering the jacks, making the access to the bolts a frustrating 'feel for it' experience.I'f suggest the manufacturer secure the bolt so that you don't need to hold both sides when tightening/loosening, and also refine it to need less turns to do so. It took me 2 hours to mount the first time, and not much less when removing them with the limited access. The pads also came off in the first use.
I gave it a 5 star because I realize there are limited options for older campers and anything universal is going to have issues with some thing - so that's just my input and experience. Overall pretty reasonable for the price and functionality.
by: Pat03/20/2023
The product was shipped extremely quickly, it arrived 3 days after I ordered them. As far as the product goes I was extremely pleased that they were as easy to install as the product video showed them to be. I had been looking for
a tie down system that would work for my 2018 Ford since I purchased my camper in 2020 and after much research I found these at etrailer. One word of advice is that if your camper has a shower or other design that allows the camper to extend across the bed behind the wheel wells, either move the rear tie downs forward or shorten the leveling stud before you attempt to load your camper. On mine it turned out that once the tie downs were placed and attached I had to cut off about 3 inches of the threads.
Other than that it was an easy install although the bolts that attach the tie downs to the under lip clamp are a challenge to install but take your time and they will go on. I will post an update once I have been on the road for a few trip and see how they are working.
Thank you etrailer for your super fast shipping and online product videos.
by: Jeff Smith10/22/2023
These tie downs work great. It holds my 3k lb Cabover camper in place without issues. And I live in my camper, so not losing my home is very important to me!!
by: Ed B.05/21/2019
Purchased the Brophy camper tie down set of four for the Palomino truck camper I just purchased. These are my second set as the first set were sold with my Hallmark camper. Easy to install and hold the camper in the truck with no worries.
by: Shelly12/13/2023
The products arrived on the time scale as stated. The packaging did not hold up and the box with the metal tie downs was broken open. There was too much weight for the box and it just split open. Not sure if anything is missing. Packaging of items that are heavy should be more secure and sturdy.
Jenny N.
12/14/2023
Oh no! I will have our Customer Service team reach out to you. If anything is missing we can take care of it.
by: Allen.08/22/2022
These wont work for my truck and camper. The box on a 2018 gmc 2500 short bed does not lend well to placement of these in order to get the correct geometry i needed for the tie-down points on my Palomino maverick 6601. I had high hopews of not having to buy the frame mounts, but i will have to.
Mike L.
8/31/2022
The HSSF tie downs have specific fit parameters as mentioned in the product specifications above: External bed rail width cannot exceed 5-12 Requires at least 2 of space beneath lip of bed rail Not compatible with -in bed liners, bed rails, double-walled beds, or side-step beds
Allen.
8/23/2023
In response to the etrailer comment response, they fit on the bed fine, with plenty of clearance and would work for a smaller camper. they just did not fit in the right spots for my truckcamper combo.
by: Ron W07/02/2016
As far as I'm concerned these are junk. Wasted my money. Do not mount in proper location on a 2011 Chevy Silverado 6.5' Bed. Because of the design of the bed rail the mounts cannot be installed in the proper locations for securing camper. The photos show the maximum forward and back that these can be mounted. Not at all made for the 6.5 foot bed 2007 or later Siverado. The Black Powder Coated Steel isn't that great either. Paint missing, dinged up from storage and shipping probably.
by: Matt04/14/2015
These camper hold-downs appear to be manufactured from good steel stock and should do the job nicely. I did have one piece that was slightly damaged but was not caught when packaged (the damage was not due to shipping). I was able to take a hammer to the bent steel and straighten it sufficiently to use the part. It was a little disappointing however, and should have been caught prior to shipping.
Overall I am pleased with the quality and price
by: Brent 08/08/2019
I bought these for our brand new 2019 GMC Sierra 1/2 ton because no custom options were available. I was happy that they were easy to install, and look great. I’ve used them in the past and have been happy with how they hold campers. Sure I’d rather have custom mounts from the frame, but for the price and because these are my only option that’s what I got. These will work just fine, and I like that I can swap these out on trucks.
The one thing I wish was different was that the threaded T handle portion would have a longer option. I had to fancy up a 2”x6” to run inside the side of my p/u bed so they would touch something.
As always another great shopping experience with etrailer. They haven’t let me down yet. Especially Lori, what a great customer service rep.
by: . George01/03/2024
The tie downs are great no problems.Very easy to install.I keep them on my truck all year long Thank you
by: Terry08/08/2023
Order arrived quickly, priced ok. Box was broken open by shipper NS the 4 T-bolsts bolts ere missing. Etrailer shipped ou the missing parts a few days later, but in the meantime I fashioned t-bolts I could use for my trip. Many customer comments on this camper Brophy tie-down match my experience. Etrailer follow up was great, but surely must be aware that their packing is sub-standard. Perhaps zip-tying the T-bolts to larger pieces would eliminate the loss even in case of breakage. Functionally the tie-dows were easy to install and seem quite adequate for off-road use of my in-bed camper. Will continue to use etrailer because of their excellent customer service.
by: Chuck11/13/2012
Found easy to install, I placed lock washers on the 8 3/8" bolts. Sold at Menards for 89 cents (pkg of 8) not in kit. Placement was a little restrictive with dealer installed bed liner. Takes 30 minutes to install all 4. Great buy.
by: captkirk02/15/2021
These tie-downs worked awesome for our pop up camper on our 1998 F150. Super snug, haven't loosened up or moved on the truck, camper hasn't budged either. I was leary at first not having the camper tied to the frame but now I have total faith in these tie downs.
by: Mike S05/23/2020
These Brophy tie downs have worked great over the past year. I leave the camper on the truck and it is my daily driver as well as RV. The camper weighs in at 1500 dry and about 2000 loaded. I do not do any radical 4x4 but I have taken some backwoods off road logging trails.
by: Bing09/23/2019
I received this tie downs on July, and first used it yesterday.
My Camper ‘s dry weight is about 1600 lb, and the products are good for my truck camper.
The problem was the position where tie downs were fitted on my truck. I tried several times to fitted tie downs to my truck.
by: Patrick04/02/2020
These things are solid although i put duck tape on the T pads....installed 2014 Chevy Silverado 6.5 ft bed for 1200lb Starcraft.
Patrick
4/6/2021
Still have not moved! Great design and cost savings.
by: Regan06/25/2019
Using on 2013 Ford F150 for a smaller cabover. Great quality product, shipped fast, works great. Had to turn bolts around to clear inside of bed. Held camper solidly over rough trails!
by: Bryce05/10/2022
Fits well on a First Gen Tundra. I was extremely unsure about fitment for my truck but they work great! Install only takes 5-10 minutes. I would definitely recommend. Steel is quite thick and seems very strong.
by: John05/25/2020
Easy to install and have done what’s expected. Keep the camper in place!!
by: JAMES K09/24/2012
ORDER ON TUESDAY RECIEVED ON FRIDAY NOON SAME WEEK ONLY PROBLEM WAS 4 7/ 16 NUT WERE 4 1/2 NUT HAD TO BUY 4 NUTS OTHER THEN THAT I WOULD BUY OFF ETRAILER AGAIN VERY GOOD SERVICE
by: Andrew07/22/2021
If I could give a 3.5 out of 5, I would. These tie-downs serve their purpose, but definitely not recommended for a bigger camper. I would say my camper is average sized. These tie-downs hold my camper in place the majority of the time, some small movements when I'm on rough roads, but nothing too dramatic.
Negatives.
Two of the four lost the padded backing where the tie down meets the inside of the truck bed. Had to go buy some foam and create my own. They flex quite a bit with a camper the size of mine, wouldn't go down any rough roads.
by: Neil08/04/2021
Arrived on a rainy day with the box falling apart. Too much heavy steel to be loosely packed. Fortunately, the hardware bag was still there. Some bare metal showing. I had some emails with MacKenzie B. and they were responsive and without asking they offered me a 5% refund for the damage. After my first trip, they performed well on some very bumpy roads. Held strong and didn't move. I did have to re-adjust the lower standoffs after the first week. Taking them on/off is frustrating because the 2 nuts are in the small gap behind the clamp against the inner bed wall. Too tight for all but an open end wrench. 1/6 turn times too many fumbling tries, arg! Also, I was nervous not having a locking feature (lock washer, locknut, etc). I bought 8 locknuts (pinch type) and welded them to the inner plate. Then bought 8 round head hex bolts (grade 8). So now I can install easily with an Allen socket. See pictures. Recommend eTrailer consider this modification.
Neil
8/5/2022
After my mount bolt mod, Ive used these multiple times and they are working great! Very stout and no visible marks on my F250 bed.
by: D Gagnon05/14/2017
Could be happier took about 15 minutes to install can't wait to go camping
by: Dayton12/15/2023
Awesome customer service my new fav pl ace
by: Jason S.06/05/2019
These tie downs were a great budget solution in leu of a permanent installation of my camper shell and/or frame mounted tie downs. Aside from needing to plan their placement (they can hang in front of the gas cap if you don't plan it right the first time around... no, I didn't accidentally block my gas cap... maybe I did) and take into consideration they also need a little bit of internal clearance as well, they work just fine. I haven't noticed any cargo shifting nor warping of the truck bed around where they are installed. My camper shell is under 1K lbs and it holds just fine.
Jason S.
6/8/2020
A year later & they still hold strong.
25
216
Show More Reviews
See what our Experts say about this Brophy Camper Tie-Downs
- Will Brophy Camper Tie Downs HSSF Fit 2001 Chevy SilveradoYes the Brophy camper tie downs part # HSSF that you referenced do fit your 2001 Chevy Silverado. We had the chance to install these on a similar Chevy truck and they fit well. Check out the review video and install pictures I attached as well. You'll need the hardware kit # TDHP as well to attach them to your camper.
view full answer...
- Will Camper Hold Down # HSSF Fit a 2011 Ford F-350I went out to the warehouse and pulled a Camper Hold Down, # HSSF, to measure so you could compare the measurements to your truck to determine fit. The hold down will go around a bed rail that is no wider than 5 inches. The top part of the hold down is 6 inches wide while the bottom, more narrow part is 3 inches wide. The top 2 bolt holes are 3-5/8 inches apart on center. It has an overall height of 11-3/8 inches.
view full answer...
- Will Brophy Camper Hold Downs # HSSF Work on a 2013 GMC Sierra 2500 with Rhino Bed LinerThe Brophy camper hold downs # HSSF can be used with spray-in bed liners but drop in bed liners would have to be trimmed. If you do not want to trim then going with custom fit frame mount brackets is the way to go. I included a link to the main page for these brackets for your truck. You will need to use the drop down menu near the top of the page to Select Vehicle Style for the proper configuration of your truck to get the right ones.
view full answer... - Camper Hold Down Availability for a 1989 Nissan HardbodyThe Camper Hold Downs, part number HSSF may work on your 1989 Nissan Hardbody. The hold downs do not fit in the stake pockets (which it doesn't look like you have) but wraps around the bed rails and are mounted inside the bed. There is no weight capacity rating on the hold downs and the will work for any camper size that is properly sized for your vehicle. I added a couple of dimension pictures of these hold-downs for you to compare to your truck bed to see if they will fit. I also added...
view full answer...
- Will the Brophy Camper Hold Downs # HSSF Fit on a 1996 Ford F-150Yes, the Brophy Camper Hold Downs, item # HSSF, will fit on your 1996 Ford F-150. These Hold downs do not install in the stake pockets, but wrap around the bed side. The instructions, see attached link, show the installation in detail. You may also be interested in the Camper Tie Down Hardware Package, item # TDHP.
view full answer...
- Does the Brophy Clamp # HSSF Fit A 2018 F150 Crewcab 5.5 BedYes, the Brophy Clamp On Camper Tie-Downs # HSSF will work just fine with your 2018 Ford F-150. The Brophy Tie-Downs are easy to install and remove and require no drilling for installation. The Brophy Tie Down # HSBP will work for you if you have the required 5.5 inches of maximum width and have the 2 inches of space under the bed rail. In order to secure the truck bed camper to these tie-downs you will also need the Brophy Basic Turnbuckles # TDHP. If you have any further questions please...
view full answer... - Does Brophy Camper Tie Downs # HSSF Fit 2018 Ford F-150 6-1/2 foot BedYes the Brophy Camper Tie Downs part # HSSF do fit your 2018 Ford F-150 with a 6-1/2 foot camper.
view full answer... - Will TorkLift Camper Tie-Downs Fit with 3-Step N-Fab Nerf Bars on a 2016 Ram 3500 Short BedAccording to the pictures that I could locate of the 3-Step N-Fab Nerf Bars for your 2016 Ram 3500 I don't think the TorkLift Custom Frame-Mounted Camper Tie-Downs # TLD2132 are compatible. I am attaching a photo from the TorkLift instructions so you can see where the front tie-down will sit. Since this is the case you will either need to scratch the idea of installing the TorkLift tie-downs and use something like the Brophy Camper Tie Downs # HSSF with the Tie Down Hardware Package #...
view full answer...
- Will the Camper Hold Downs, # HSSF Fit a 1975 Rancho El Rae and Ford F-250The Camper Hold Downs, # HSSF, will work with any camper that is a fit for your truck. These hold downs do have some limitations as to what trucks they will fit. If your truck bed is a step side or has a double wall, they will not fit. However it is likely that it will work for you. Take a look at the installation pictures I have included for you. I also recommend using the camper tie down hardware package, # TDHP.
view full answer...
- Brophy Camper Tie Downs Compatibility With A 2020 Ford F-350 Super Duty With Factory Spray Bed LinerAs long as your external bed rail width does not exceed 5-1/2" and you have at least 2" of space beneath the lip of bed rail the Brophy Clamp On Camper Tie-Downs # HSSF will be a fine fit for your 2020 Ford F-350 Super Duty with a factory spray bed liner.
view full answer... - Will Brophy Clamp On Camper Tie-Downs Work With 2016 Ram 3500 Pickup TruckThe Brophy Clamp On Camper Tie-Downs, part # HSSF are designed to fit most full-size non-dually pickups. There are a few things you will need to check to make sure these tie-downs will work for your 2016 Ram 3500. First, the bed rail width cannot exceed 5-1/2 inches. These tie-downs are not compatible with drop-in liners, plastic bed rails, double walled beds, or side-step beds. This kit comes with 4 tie-downs, neoprene pads, and the hardware needed for installation. If you find the...
view full answer... - Recommended Truck Bed Camper Tie Downs for 2004 Ford F150According to my contact at Brophy, the # TDSF stake pocket tie-downs will work with your truck, but your camper would need to be 8 feet long or shorter. You would also need the Tie-Down Hardware package, part # TDHP which includes the turnbuckles and chains. Their # HSSF system will not work with the 2004-2008 F150 Trucks. If your camper is longer than 8 feed, Torklift offers some tie down solution, but I would need more information about your truck. I would need to know: Does truck have...
view full answer... - Can Brophy Camper Tie Downs Handle a 3,300 Pound Camper in a 2006 Chevy Silverado 2500There is no weight capacity rating on the camper tie downs # HSSF and they will work for any camper size that is properly sized for your vehicle. The associated hardware package # TDHP does have a weight capacity of 3,000 pounds so you wouldn't use it. Instead you could use 2 sets of # TLS9000. Ideally though you would use frame mounted tie downs custom fit for your 2006 Chevy Silverado 2500. If you want to explore that option I have included a link to them for you.
view full answer... - Will Brophy Camper Tie Downs Work on 2020 Chevy Silverado 2500 Long BedYes, the Brophy camper tie downs part # HSSF that you referenced can fit truck bed that have plastic bed rail covers like your 2020 Chevy Silverado 2500. I attached a picture that shows them installed on a bed rail that has the covers like you mentioned. For hardware to attach the tie downs to the camper we have the # TDHP as well.
view full answer...
- Camper Stake Pocket Tie Downs for 2003 Dodge 2500 2WDYes, the stake pocket camper tie downs, # TDSF, will work on the 2003 Dodge Ram 2500, as long as the overall length of the camper you are using them with is 6.5 feet long or less, this measurement includes the overhang over the cab of the truck. You will need to drill one 11/32 inch hole and two 7/32 inch holes for this installation, and there are spacer tabs on the tie downs that may need to be pried off for a proper fit in your stake pockets. If your truck campers overall length is...
view full answer... - Will Camper Tie Downs Fit a 1997 Chevy Z-71 and What Other Parts are NeededYes, the Camper Hold Downs, part number HSSF will work on your 1997 Chevy pickup. The hold downs do not fit in the stake pockets but wrap around the bed rails and are mounted inside the bed. They will work for any camper size that is properly sized for your vehicle. You will also probably need a tie down kit. The Camper Tie Down Hardware Package, item # TDHP, comes with four 3/8 inch turnbuckles, four S hooks and four chains and works with the camper hold downs. This hold down kit has...
view full answer... - If Brophy Camper Tie Downs Bend Can they be Bent BackIf the bend wasn't enough to affect the integrity of the tie downs then yes you could bend them back. So basically bend them back and as long as you don't see any metal creasing, paint flaking, or any other obvious signs of stress you'd be fine. If they are stressed to the point they need replacing these have a 1 year warranty.
view full answer... - Camper Tie Downs for a 2005 Dodge Ram DuallyThe Brophy camper tie downs, # HSSF, fit most domestic full size trucks, but there is not a specific vehicle list that they will fit. You will have to go by the measurements of the tie downs and the installation instructions to determine if they will fit your 2005 Dodge Ram Dually. I have included some pictures that should help. We also have some stake pocket mount tie downs that could fit, # TDSF. With either tie down kit, you can use the Camper Tie Down Hardware Package, # TDHP.
view full answer...
- Can Brophy Camper Tie Down # HSSF be Used with Camper that is Longer than 8 FeetYou are correct the versions of the Brophy camper tie downs that attach to the truck bed rail pockets are limited to 8 foot long campers but the clamp on style like part # HSSF can be used with longer campers like what you have and will work great with your 2003 Chevy Silverado 2500HD.
view full answer... - Will the Brophy Camper Hold Downs Fit a 2012 Chevy Silverado 1500 with 6-1/2 Foot BedIf it is not a dually and does not have a step side or double wall bed, then the Camper Hold Downs, # HSSF, will fit your 2012 Chevy Silverado. These hold downs wrap around the bed rather than fit inside the stake pockets and will work for any camper that is a correct fit for your vehicle. You can also use camper tie down hardware kit, # TDHP, with the hold downs. To install, first place the protective tape under the rest plates and on the T-Bars. Next, thread the T-Bar into the nut at...
view full answer... - Camper Tie Down Recommendation for a 2003 Toyota TundraFor your 2003 Toyota Tundra you would want the Tie-Downs part # TDSF. We had a customer use these on his 2005 Tundra (same generation as yours) and let us know that they worked very well for him. The # HSSF that you referenced is a universal kit that could work for your truck, but we don't have fit information for this kit so your best option would be the # TDSF since we know it would work for you. You also will want the Camper Tie Down Hardware Package, # TDHP.
view full answer... - How to Connect Camper Tie Downs to CamperThe HSSF hold down brackets would use the Tie Down Hardware Package, part # TDHP, which includes hooks, chain and turnbuckles. The tie down hardware would typically attach to existing eye bolts built into the underside of camper. If your camper does not have such an attachment point, you can add them, as long as they attach to the frame of the camper. The Steel flanges shown in the photo you provided could be used as attachment points for the hardware if they are connected to the camper...
view full answer...
- Camper Hold Down Recommendation for a 2011 Ford F-150The Brophy Camper Hold Down Brackets, part # HSSF are a universal-fit item that will work on most full-sized trucks, including your 2011 Ford F-150 as long as the camper is designed to fit on your truck. The brackets wrap around the bed rail, instead of using the stake pockets. The brackets include the hardware for fastening the bracket to the truck, but we also offer hardware to attach the camper to the brackets, the kit is part # TDHP. The kit includes 4 turnbuckles, 4 S hooks and 4...
view full answer... - Camper Tie Downs that Attach to Stake PocketsI have a much better solution for you than the part # EM09085 as a camper tie down. The Brophy Camper Tie Downs, part # TDSF, you have referenced are a universal application. The hardware to mount the tie downs to the vehicle are included. These tie downs will fit campers up to 8 feet in length. If you have a larger camper I would recommend the Brophy Camper Tie Downs, part # HSSF which is a more heavy duty tie down. The tie downs wrap around the bed, not in the stake pockets, and...
view full answer...
Do you have a question about this Camper Tie-Down?
Used Items Available
Condition: Installed
Notes: Item has been installed/test fit.
Condition: Surface Scratches
Notes: Parts are scratched up, seems to be some signs of instalation, otherwise fine.
Info for this part was:
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Jeffrey L
Expert Research:
Sarah H
Video Edited:
Zack K
Video by:
Patrick B
Installed by:
Matthew K
Installed by:
Cole B
Updated by:
Rachael H
Updated by:
Amanda M
Updated by:
Manda E
Updated by:
Amanda K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Ed B.
5/22/2020
No problems. Would buy again. Very easy to take on and off the truck.