Most Popular 500 lbs Vert Load for Ford Ranger

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Great solid piece, as you would expect. Extra longer bolts are included in case you have the factory tow hooks, a nice touch and saves $10 at the hardware store. Not a complaint, just info; you have to remove the bumper to fit the front bolts, they won't drop in past the bumper brackets at least on my '95. Cut a hole and some minor trimming, and it works with the factory air dam as well.

UPS was 8 days late for no good reason though it looks like they used the hitch as a crash test dummy. It’s a miracle the hardware bag made it but it did! I think this is superior than the other brands available. They always include these little threaded fish tape wires for getting the hardware into the frame. I’ve done a transit and now this. Saves a ton of time/headache. However the instructions just have a diagram. Took me about 20 min to get the first bolt in. Then 20 min for the rest of the install. So if you read this, you can probably get the whole thing done in 30 or so which is what i expected initially. Tools: 3/4” socket Torque wrench 1/2” drill bit & drill OPTIONAL: floor jack to lift hitch into place. Steps: - Drill forward holes to 1/2” and shoot with some rustoleum or equivalent paint. Let dry for 20 min while you eat lunch, take a dump, whatever. - send fish tape through forward mount hole and out front of frame rail. Figuring this is what slowed me down on the first one. the carriage bolt head won’t fit through any of the obvious openings. See pic. - put to bolt plate onto the fish wire then thread the bolt onto the wire. Pull em all through the hole and watch it assemble right before your eyes! - repeat on the other 3 bolts - jack hitch into place and finger tighten the washers/nuts on - torque down to 75ftlbs and boom! time to yank or be yanked! See all my pics and if this helps, send me an imaginary beer through the quantum field! Econolines rule!

I tried ordering this exact hitch off Amazon. Not once, but twice they shipped the wrong part number. Took a couple months to get my money back. Etrailer got it right the first time. I took about an hour to install on my 2006 class B+ E 450 motor home. The best advice I can give is take the 15 minutes to remove the front bumper (21 mm). With front bumper removed you won't need the wire chaser things. Jus stick your hand in the frame.

2nd hitch, both fit up great. Left off the roll pan and built our own cover for the sway bar disconnect.

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

This front receiver mount is exactly what I needed. Great build quality and easy to install. Thanks for getting it to me in a timely manner.

After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!

The front hitch solved a storage problem that I was having with my truck camper.It fit perfectly. I added a Stow Away hitch frame and a UWS small aluminum storage box for my small generator. The photo shows a test fit before installation.

This was one of the easiest accessories I’ve installed on my Tundra. It is a front receiver hitch so I don’t use it very often. Mostly just for bike racks when towing a trailer, but when you need it you need it.

The fit was a bit too tight but we were able to make it fit. The shipping packing was pretty lacking. Since being installed we have been using it with a spare tire mount. That works great and it makes the spare tire more accessible compared to the standard under the bed mounting. When fully loaded with a camper and towing a boat moving the spare tire to the front improves the weight distribution.

Curt actually recommended that we use etrailer. They even gave me the confirmation that the hitch would work and told us you have a video. Thanks!

I purchased this front receiver hitch for my 2010 Ford E350 RV to use for a utility basket, launch a 16' boat and now also for a motorcycle carrier. The quality is excellent and full weight rating, one year later and the finish is perfect. Installation was exactly as stated in the directions and the modifications were minor, requiring existing holes in the frame forward of any critical mounts drilled larger and the plastic under the front bumper where a tag goes has to be cut slightly to allow for receiver. The directions called for removal of under carriage splash guard but I was able to trim and reinstall. I am perfectly happy with the purchase. When hauling a motorcycle on the front the RV rides so much smoother and better planted on the road without being overloaded.

Have been an e- trailer Cust for most of my hitch and trailer needs for years. The RAV4 hitch and air bags have been a real plus cause the Mrs uses it like a mini truck. The hitch attachments and extensions we’ve bought all top notch - expect nothing less from this front mount hitch for our c class Rv. Recommend you always check with them first before buying elsewhere.

Mounting went well,video direction were accurate.

Overall, my experience with etrailer was good. There was an initial delay in shipping, but once I talked to someone, everything went well. The help page was invaluable. The biggest help was the installation video. While there are slight differences between the 2011 GMC and the 2013, the process was the same. I am very pleased with the product and the support. Picture attached.

It is a great hitch I have a front rack that’s on it now to haul my generator and fire wood also I’ll be using it for my bike rack to haul my e-bike with , did lose my mind on the bolts I did get some help to get them in,tho my patience ran out, but all in all it’s a great hitch.

Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.

This hitch was very easy to install....I had to trim the lower air dam to fit around the receiver and that gives it a clean neat look. I didn't like that I had to remove and leave the shields around the tow hooks off. But overall I'm very pleased. I plan to use this hitch for maneuvering a camper in a narrow spot beside my home, and for a bike rack when towing a camper.

I gave this hits only 4 stars since all of the available information indicated it would bolt right on to my 2003 Avalanche 1500 (All Models) with no modification, but it wasn't quite that simple. First off, my Avalanche has the plastic cladding. The end brackets of the hitch push the bottom of the air dam under the bumper down a bit and make it bow out. I had to remove the bracket that secured the air dam to the center of the frame. I mounted the hitch in the upper position since I didn't want it to be so low, and the receiver ends up being 8" back from the bumper facia. I had to order an 8" extension to bring it out past the bumper. Other than that, I'm happy with the hitch. I just wish the fitment guide was a little more specific.

UPS was rough on the box but everything still lined up without having to pry but was snug on the back bolts. Install was very straight forward and did it myself in my driveway in just about 90 minutes from pulling the air dam to putting tools away. Used my floor jack to support the hitch in the center and started with the front bolts on both sides and then pivoted the hitch into position for the back bolts and then snugged up all four mounting bolts to the 110-ftlbs torque spec. Hints. made sure that front of the hitch was just a a hair pointed up from level before tightening down all of the mounting bolts. I pulled the air dam completely off and then lined it back up in position lying on the hitch so I could marked it, so I knew exactly where I would need to trim it and then used my Dremel tool with a cutoff wheel to trim it to fit. Then bolted it back into position and was done. I'll try and update this post once I take some pictures other than the shipping box

Please read: I am not happy with this product. I have a 2023 F-150 with a 2” leveling kit up front. My properly installed hitch only has 8-3/4” of ground clearance sitting on my flat garage floor. It definitely appears to be the lowest point throughout the whole bottom of my truck.I didn’t even have to cut my air dam for the unit to align with the mounting holes in the frame. Like anyone else I wanted this to sit as high as possible, forcing me to cut as much air dam as possible. I believe the mounting holes in this hitch were drilled way too high, and now I’m either stuck with terrible clearance or I need to take it off and re-drill the holes lower on my own. Plus it points downward out the front and not on the same parallel plane as my truck. I put an accessory in it and it was barely above the ground out front. Super irritating. See photos. If anyone has help I’m certainly listening. The shipping and ordering was super fast and easy otherwise this would be 1 star.

After struggling with the answering menu, Steve Z. was instrumental in locating a hitch to fit my van which was not specifically identified in any data search. Weird year, 2005, of popular Chevy Express van, my luck! Using manufacturers dimensions I purchased #31016 on 12/21 and it arrived on 12/24. It's a very well built, USA built, unit. It arrived rapidly, but was missing half of the mounting hardware. The remainder of the hardware was rolling around in the box. Zip lock baggie ripped apart spilling them. I used a hydraulic jack to elevate hitch into place, and an additional jack to push the drill up to drill the 6 mounting holes necessary. No factory hole alignment. All the nuts for the bolts were lost in transit, but by a Christmas day miracle, I found 2 metric nuts to fit supplied bolts that survived the delivery. I will acquire, and install remaining missing 4 tomorrow. The installation went smooth and easy using this technique. It took around 3 hours with much of the time searching for hardware.' Thanks Steve Z. and etrailer. .

The product works great. However, I was told that this front hitch receiver would bolt to existing holes on my 98 Four winds RV. That was not true, so installation was double the cost of what was estimated by the shop I took it to.

This receiver hitch fit my 2015 Ram 2500 fine, and looks good. However, Draw-tite quality control must be a bit lax, as now that I tried to use it, I find the hitchpin holes are not the same size and even a standard pin cannot go through both holes (so as is, I cannot use the now-mounted hitch). I am going to have to bore out the hole(s) to the correct size for a locking pin, to mount the hitch-mount winch I intended to use in my dump trailer and my truck. In addition to being the wrong (or mismatched) holes, the location of the holes is right next to a beefy weld that will make securing (whether by locking or non-locking hitchpin) difficult. I cannot justify removing the receiver after all the work it took to install, but definitely cannot give this a good review. I recommend test-fitting your pin(s), tow balls, winches on it before you waste time installing. However, as always, etrailer.com rocks!

I have always wanted a front bumper receiver but always resisted because I thought it would require welding, this unit is bolt on and went on my Ram 2500 with no problem at all, it looks like it was factory installed.

This hitch came quickly and I believe was priced fairly for what you get. Unfortunately, as some other have posted, this hitch is intended for my vehicle (1996 Ford E350 RV) but did not fit correctly. I had a problem with the front holes not being spaced far enough apart for the bolts to fit. The rearmost bolts go into a oversized and slotted hole in the underside of the frame so there was no problem with those, but the front holes in the frame have to be drilled out to 17/32" for the supplied 1/2" bolts per the included directions, and I couldn't get the bolts in both sides. The bolt holes in the hitch needed to be approximately 1/4" further apart. Also, there is a relief cut out of the hitch that I assume is to miss a bump on the under side of the frame. This cut out is in the wrong location to miss the bump in the frame. I went ahead and torched the slot for the bolt a little longer on one side and made the cut out for the frame bump bigger on both sides. A little grinding, a little touch-up paint, and back on she went. Had to notch the lower plastic valance just a little bit to clear the receiver, which was expected. Actually had to cut it a lot less than I thought I would. The two safety chain loops sit right under the valance, but I don't for see the need to hook anything to those, so I opted to not hack up the valance at this time. I intend to put a bike rack on the front, and also use the hitch to get drug onto the beach at Pismo from time to time. Hopefully the cuts I made don't weaken the hitch for that purpose. The directions call for this to be a 20 minute install. Granted, I took off the bumper, but even if I hadn't, and the hitch was fitted correctly, I find it hard to believe anybody could get this done in anywhere near that time. As another reviewer said, now that it's on, I'm a happy camper, but it was a little bit of a job to get there.

Worked great for hauling my motorcycle on the front of my motorhome. Lets me pull my boat and have transportation when I get where I'm going.

Works well, fairly easy to install.

Easy installation on my 2007 GMC Sierra 3500 dually. I installed the hitch to transport e-bikes. Works great and solid.

Fit my 2018 MB Sprinter perfectly. Install was straightforward. Wonderful step by step instructions included. Shipped fast. Psyched to travel with e-bike hitch out front. Thanks etaailer

After spending the better part of 4 hours trying to disassemble the front of my Sprinter, I've discovered I can't install on a 2022 Mercedes Sprinter outfitted by Tiffin (GH1 model). ARB hose attached to rock plate in front will not easily disconnect. Also unable to unbolt passenger side bracket for rock plate as it hits the radiator.

We chose the Curt Front Mount Trailer Hitch Receiver so we could safely transport our RAD electric bikes while also pulling our travel trailer. We had it professionally installed onto the front of our Toyota Tundra and it has worked out very well! We are very pleased, and glad that we have it!

Shipping was fast and packaged good with no scratches. I modified my 2010 Tundra skid pan for oil filter changes before mounting. Replaced all 4 OEM tow ring bolts using anti-seize with new longer M12-1.25 X 40MM class 10.9 zinc finished hex cap screws along with new M12 X 24MM OD HARD WASHERS and torqued all 4 to 79 ft/lbs. Mounted new Thule EasyFold XT 2 Hitch Bike Rack and it fits in front without using the hitch extension. All went together as planned and can now take E-Bikes with us while pulling our camper. We are happy campers!

Installed on the front of a 2008 GMC 4x4 Sierra. Primarily utilized for a hitch mount snow plow (DK2). Installed without any modifications - works good with the plow. * The hitch sits low to the ground (stock suspension). I installed a 2" leveling kit from RC and that helped with clearance. I am satisfied with the quality of the product - will purchase again from Curt for my Durango

Front hitch fit perfectly on a 1995 K1500. I was able to install without modifying the front tow hooks nor the fascia. This is the hitch you want.

I chose this hitch over the Curt simply due to cost. Shipping was very fast. Installation requires 2 people. I had the luxury of a lift and I'm not sure if I would've been able to do the install without it. There are only 4 bolts and was done in about 30 minutes just as the instructions claim. I held it up in place temporarily and then just marked the air dam with a pencil then cut the notch. No removal of the air dam is necessary. I love the fact that it is so hidden under the license plate holder. And the air dam in front hides the rest. Nice product !

Installation was simple, with the included fishing wires to guide and pull the bolts through the hitch and frame rails. I did spray paint the hitch with rubberized undercoating because it is more exposed to the elements on my truck with the air dam removed. The whole reason for this assembly was to mount a plow to my '16 Chevy Colorado and it works perfectly.

This worked great on my F350 dually. We needed a front hitch to carry bikes while towing a 5th wheel camper. Instructions were easy to follow

This appears to be a great receiver hitch! The first one arrived bent because UPS employees threw or dropped it. e Trailer was fabulous in getting another one out ASAP. Assembly and fit was great as well. The only recommendation I would make would be to provide a template with measurements to cut the front rubber air damn to ensure a factory finish.