Most Popular 9000 lbs Line Pull for 2021 Ford F-150

This hitch is high quality and fit perfectly. Install was relatively easy. I needed this hitch because I tow a travel trailer and need to carry my bike rack and bikes as well. I can move the bike rack to my rear factory hitch when I'm not towing, very simple. The pictures show my truck / RV with my bike rack installed in the front hitch.

I use the hitch for our E-bikes bike rack. It is so nice to use especially since I tow a camper and didn’t have a way to haul the bikes. Very sturdy and it was easy to install.

UPS was rough on the box but everything still lined up without having to pry but was snug on the back bolts. Install was very straight forward and did it myself in my driveway in just about 90 minutes from pulling the air dam to putting tools away. Used my floor jack to support the hitch in the center and started with the front bolts on both sides and then pivoted the hitch into position for the back bolts and then snugged up all four mounting bolts to the 110-ftlbs torque spec. Hints. made sure that front of the hitch was just a a hair pointed up from level before tightening down all of the mounting bolts. I pulled the air dam completely off and then lined it back up in position lying on the hitch so I could marked it, so I knew exactly where I would need to trim it and then used my Dremel tool with a cutoff wheel to trim it to fit. Then bolted it back into position and was done. I'll try and update this post once I take some pictures other than the shipping box

Please read: I am not happy with this product. I have a 2023 F-150 with a 2” leveling kit up front. My properly installed hitch only has 8-3/4” of ground clearance sitting on my flat garage floor. It definitely appears to be the lowest point throughout the whole bottom of my truck.I didn’t even have to cut my air dam for the unit to align with the mounting holes in the frame. Like anyone else I wanted this to sit as high as possible, forcing me to cut as much air dam as possible. I believe the mounting holes in this hitch were drilled way too high, and now I’m either stuck with terrible clearance or I need to take it off and re-drill the holes lower on my own. Plus it points downward out the front and not on the same parallel plane as my truck. I put an accessory in it and it was barely above the ground out front. Super irritating. See photos. If anyone has help I’m certainly listening. The shipping and ordering was super fast and easy otherwise this would be 1 star.

This thing is well built, it fit perfect, This will come in handy for my needs. Instructions are very clear. If I was to rate the install on a 1 to 10 scale it would be a 5. Fishing the bolts thru the frame with the wire provided was much easier than I expected. I do recommend this hitch.

the install went very good but i do have one suggestion and see if your maker can put a notch in the middle hole to look like the tow hook it would make the install way more user friendly also had a little problem with one of your bolts after i had fished it down the hole the treads were burred and the nut wouldn't go on all the way so i had to fish it back out what a pain that was but got it done and replaced with one of the other bolts that you supplied me with and it went on great. now i have a ? about the hitch height mine only sits up at about 11 inches and change will that work with your snowplows that say they need 13 inches or will i have to do something different? but thanks for the great turn around time in getting it here quick.

2003 F-150 4X4 Lariat. I accomplished installation alone in about 1 hour as a complete newbie. Here are my tips: 1. Read instructions and other comments ahead of time. 2. Spray the tow hook bolts a day or two ahead of time with a penetrating oil spray. 3. There is nothing to hold the factory nut plate (inside the frame rail) when the tow hook bolts are removed. After I removed the first tow hook bolt and loosened the other one for some "working room), I threaded a thin piece of flexible wire through the bolt hole and nut plate, out another nearby hole on the side of the frame rail and twisted it together to keep the factory nut plate in position. Then, I removed the second tow hook bolt and the tow hook. Leave the flexible wire in place for now. Do the same on both sides of the vehicle. 4. You have to temporarily remove the tow hooks completely but I did not have to remove any other trim / fascia. 5. The fish wire is essential. I passed the empty threaded portion of the fish wire through the bolt hole for the new bolt from below and advanced it toward the front of the vehicle. There is enough room once it comes out of the front of the frame rail to thread on the new bolt ... with the new nut plate included ... then pull it into the inside of the frame rail behind the bumper fascia ... then wiggle / "jimmy" it back until it drops into position. 6. Once the new bolt / nut plate was in position, I used a few drops of super glue to tack the nut plate into position through another nearby square hole where the new nut plate was visible. Do the same on both sides of the vehicle. 7. I used a hydraulic floor jack to position the receiver under the vehicle. A little metal lip at the center of the receiver fit right into the notches on the cup of the jack. 8. I carefully raised the receiver into position with the jack. I started a little bit toward the back of the vehicle. This let the front lip of the receiver slide forward into the fascia opening for the tow hook. Once the front of the receiver was through that, I lined it up, raised it and the new bolts (with the super-glued nut plates inside the frame rail) came through the receiver mounting holes perfectly. I put the two new nuts on the two new bolts "finger tight". 9. I raised the receiver a little further but leaving a few mm of space between the front of the receiver and the frame rail ... where the flexible wire mentioned above was coming out. The holes should line up at this point. Leave the flexible wire in place for now. 10. Use one hand to hold the tow hook in position. Thread one of the original tow hook bolts through the the tow hook, the receiver, the hole in the frame WITHOUT the flexible wire and into the nut plate inside the frame rail "finger tight". This will "grab" the factory nut plate inside the frame rail. Now, you can untwist / pull out the flexible wire through the other tow bolt hole and thread that bolt as well. Repeat the process for the other side of the vehicle. 11. Now, all 6 bolts / nuts are threaded in position "finger tight". Tighten / torque them sequentially ... and you're done!

Installed this hitch on my 2000 Ford F150 4x4. It fit perfectly. No facia needed to be removed and no frame drilling was necessary. I simply removed the tow hooks and skid plate and bolted up the hitch and reinstalled the tow hooks. I notched the edges of the skid plate to clear the hitch frame (small angle grinder worked fine for this) and reinstalled the skid plate. Installation was simple and straight forward. The attached pictures may be a little dark but I attempted to show the hitch tucked up against the factory facia.

No hassle installation, what you are waiting for get one for the old ford

Won’t be installing until next week.ordered Monday received Wednesday!unbelievable service and shipping!!!I will let you know about installing and fit. Thanks

Gave it 5stars cause it was so easy to install…only potential issue is its height…but…. In fairness to drill and cut brackets to raise it would require cutting “upper valance” something I’m not prepared to do….yet

I bought the front trailer hitch for a bike rack while pulling my camper and that works great. I decided to try it pushing the trailer into my garage and really like that. Takes some learning since only very small adjustments in steering wheel make quick change in the trailer directions. Installation was simple, but requires more strength than I have to lift hitch into position (tight fit) and bolt it in place. I found a local curt dealer who installed it for about a hundred bucks. Money well spent.

I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.

Hi George, I received your email and didn't realize it had been a year already. I'm afraid I don't have anything to say that you want to hear but I will tell you anyway. I spent about a week researching this hitch and read numerous reviews about it and how easy it is to install with installation times of 30 minutes to an hour, so finally I bought one. I read the instructions when I got it, looked simple enough. I've been building cars and motorcycles most of my life, a few hot rods and drag raced Harley's for 8 years, and I had to fabricate a lot of parts on the drag bike splus I've been a CNC Machinist for 30 years, and having just retired this project was on my list of things to do NOW! Well its been a year and the hitch is now sitting in the corner of my dining room. Either I have a Jeep Cherokee that is an odd ball or its just my crappy luck. In the directions it says to use the fishwire for putting in cm-sp1 and the bolt. I can supply pictures if you want but there is no access hole anywhere near big enough to get the sp1 spacer in the frame and the end of the frame isn't open either as the directions suggest. Apparently its either butcher the frame with a hole big enough to these spacers in, which I really don't want to do, or try to sell the hitch for whatever I can get and say the hell with it, except I really need that front hitch. I realize most people are very happy with your product, but I'm sorry to say I'm not at all. You asked!

I use Curt Front Hitches from ETrailer with pintle hitch plates to make my own front protective bars and also rear protective bars in a rear truck, SUV. Or van hitch to protect my vehicles from bad drivers. Much stronger than bull bar or offroad front bumper bar protection

We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.

I bought this receiver to add front mounted 'accessories' on my 2007 Jeep Wrangler Unlimited Sahara. I plan on using this to add an extra bicycle rack, a cargo basket, a receiver mounted winch or other 'accessories' needed for my Jeep when I take my family camping. It will also be useful for "front launching" a boat or parking a trailer in tight spots. It took me about an hour to install, although I had already previously removed the lower wind deflector cowling, so did not have to spend time removing it or cutting it for a finished look. Detaching and moving the top trim panel between the grill and the bumper is a must to facilitate the installation. The receiver fits pretty close, although you do have to manipulate it to get the holes to line up with the frame. Follow the instructions and do not tighten any of the bolts until you get it lined up and all the bolts in loosely, then torque it down. As noted in the instruction sheet, the driver's side of the receiver does not sit flush against the frame, there is about a 1/4" to 5/8" gap. The instructions say to use the extra split washers (in the kit) as filler, but they would just rattle around loose in there and provide any benefit, so I omitted them. Once tightened down, the receiver tube was not parallel to the ground, it is slightly higher in the front, sloping towards the rear. It is not off enough to affect my intended use, but may be bothersome to those with type 'A' attention to detail. Overall a good product that will add a lot of flexibility to my Jeep~

2nd hitch, both fit up great. Left off the roll pan and built our own cover for the sway bar disconnect.

Requires permanent removal of the front air dam. Requires temporary removal of the front sway bar. May decrease offroad performance by lowering the approach angle. Has 2 Sturdy retrieval loops.

I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer

Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.

Great solid piece, as you would expect. Extra longer bolts are included in case you have the factory tow hooks, a nice touch and saves $10 at the hardware store. Not a complaint, just info; you have to remove the bumper to fit the front bolts, they won't drop in past the bumper brackets at least on my '95. Cut a hole and some minor trimming, and it works with the factory air dam as well.

Works great for hauling our bikes. Hitch was easy to install and easier on a lift. Quality product and service from etrailer. I did have to get an extension to get bike rack past the bumper (Ford truck).

I went with this hitch since I have an after market front bumper. I wasn’t sure if it was going to fit but since this hitch was a bolted connection it gave me 2 options to have a chance it would fit. One I received the package the box was damaged but all the hardware had been taken to the hitch, so everything was there. I installed the hitch by myself and took me about 2 hours but that was due to the aftermarket bumper and dealing with that hardware at the same time otherwise the install went smooth. Tha last phot is to show this hitch worked with this bumper.

I need to thank the team @ eTrailer. The original front hitch for my Tacoma that I ordered was out of stock for a few months (Covid), and I needed the hitch for a trip in a week and a half. The eTrailer team had a different manufacturers brand at my door step in 2 days. I assembled the parts in my living room to make sure I had all the hardware, and exactly where all the bolts/washers will go. I cant wait to install it tomorrow. eTrailer had the best price I could find and delivered me the part in a very tight timeframe. eTrailer for the win!!!

My front hitch for my 2008 Tacoma got to me within 3 days very fast service. I installed it in 30 minutes and was able to put the front skid plate back on without doing any other changes to it. Very good product. I will be using it to put my rod rack on front of truck to use it at the outer banks of North Carolina for surf fishing this coming fall. Thanks for a very good hitch.

I purchased this front receiver hitch for my 2010 Ford E350 RV to use for a utility basket, launch a 16' boat and now also for a motorcycle carrier. The quality is excellent and full weight rating, one year later and the finish is perfect. Installation was exactly as stated in the directions and the modifications were minor, requiring existing holes in the frame forward of any critical mounts drilled larger and the plastic under the front bumper where a tag goes has to be cut slightly to allow for receiver. The directions called for removal of under carriage splash guard but I was able to trim and reinstall. I am perfectly happy with the purchase. When hauling a motorcycle on the front the RV rides so much smoother and better planted on the road without being overloaded.

Mounted it in a couple hours, relatively easy installation. Having to drill the mounting hole bigger took me by surprise but that's on me for not watching the installation video before buying. This is the only front hitch option for 2017 E450 RV chassis. It mounts rock solid. Standing and bouncing on it, there is no play in the hitch or the mounting point. Standing and bouncing on the hitch- the entire front suspension gives but the mount does not budge. I no longer hesitate about mounting a small motorcycle on the front of the RV- this hitch is made of metal as thick as the RV frame itself.

The fit was a bit too tight but we were able to make it fit. The shipping packing was pretty lacking. Since being installed we have been using it with a spare tire mount. That works great and it makes the spare tire more accessible compared to the standard under the bed mounting. When fully loaded with a camper and towing a boat moving the spare tire to the front improves the weight distribution.

Curt actually recommended that we use etrailer. They even gave me the confirmation that the hitch would work and told us you have a video. Thanks!

This receiver hitch fit my 2015 Ram 2500 fine, and looks good. However, Draw-tite quality control must be a bit lax, as now that I tried to use it, I find the hitchpin holes are not the same size and even a standard pin cannot go through both holes (so as is, I cannot use the now-mounted hitch). I am going to have to bore out the hole(s) to the correct size for a locking pin, to mount the hitch-mount winch I intended to use in my dump trailer and my truck. In addition to being the wrong (or mismatched) holes, the location of the holes is right next to a beefy weld that will make securing (whether by locking or non-locking hitchpin) difficult. I cannot justify removing the receiver after all the work it took to install, but definitely cannot give this a good review. I recommend test-fitting your pin(s), tow balls, winches on it before you waste time installing. However, as always, etrailer.com rocks!

I have always wanted a front bumper receiver but always resisted because I thought it would require welding, this unit is bolt on and went on my Ram 2500 with no problem at all, it looks like it was factory installed.

I purchased Curt’s custom front mount 2” hitch. Installation was easy, mounting points were accessible without necessity of a lift or floor Jack. In the year I’ve used it it has been very handy in pushing a dump trailer, car hauler, landscape trailer, diesel wood chipper uphill and around curved access and parking said trailers between other pieces of equipment and parked vehicles w/o the unfortunate scrapes and dents sometimes incurred while moving the same trailers into the same locations while attempting to back them into position. A very handy trailer hitch for parking a trailer in a crowded equipment yard.

I waited 12 days for a shipment from amazon and the hitch was lost. They want to send me another hitch with a due date of January 6, 2024! You guys are the best! 2 day’s service was outstanding!!!

It is a great hitch I have a front rack that’s on it now to haul my generator and fire wood also I’ll be using it for my bike rack to haul my e-bike with , did lose my mind on the bolts I did get some help to get them in,tho my patience ran out, but all in all it’s a great hitch.

Added to use with a front winch. The install was not too difficult and the included instructions were spot-on. On my F250, the front tow hooks add to the strength of holding the hitch to the frame. On the F250 you do lose the OEM fog light location, but I used the wiring to add/relocate after-market fog lights. The set up has already proven helpful, pulling me out of a snow back while plowing. Just what I needed for some summer off road camping as well.

Super easy to install product thanks to the video! Took all of 25 mins to install

Great product,easy installation and dealing with etrailer has been a real good experience.

Excellent instruction video! I would hope on future videos the dark black parts might be contrasted, they are taken from below and I am sure my lighting was lacking under an un-jacked jeep! The plastic rivets on vehicle are two part and in a restricted trough which were a pain to replace other than that issue everything was great!

Fits perfect and works just as I needed it to. I use it for my SnowSport plow set-up on a 2022 Gladiator Sport Max Tow. I’ve been using front receivers for this same plow for the last 24 years. It’s been used on 5 different trucks and this front receiver mount plow is the BEST. *** When installing on a Gladiator(possibly the Wrangler as well), the front plastic trim below the bumper needs to be cut for receiver clearance. I wanted a tight and “factory looking” install, so I took my time with a vibrating cutter and very sharp utility knife. After trying to put it back in place, the hole is not just square, it’s shaped more like. “T”. I suggest you make small adjustments/cuts as you go forward. It may take several times fitting and cutting to get it right and tight, but in the end it does look like it came that way from JEEP. On the Max Tow package, there is also a metal skid plate that does not get reinstalled. Unfortunately that piece is where the back of the plastic fascia mounts. I ended up securing it with some long heavy-duty zip-ties and it’s worked well for a year now. Just an FYI for those installing the same receiver on their same vehicle.