# 1
Swagman XTC2 Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Frame Mount
First-time rack buyer / owner / installer. The rack arrived in a timely fashion, maybe a day or 2 ahead of schedule. It was well packaged. I’m LOVING this bike rack. It was easy to put together and to mount on my new Honda Passport. Thus far, no squeaks in my 2” receiver. Hardest part of initial set-up is figuring out the best way to position two bikes. Trial & error and some patience. The directions weren’t clear as to where the 2 left-over screws went. I found the answer in another review and have posted a pic in case others have the same problem (photo with pen pointing at screw). These screws go in the underneath side of both of the folding arms. They appear to keep the wheel wells from sliding off in case in you drive with an empty, un-folded rack, and forgot to tighten down the wheel wells. The folding arm push / pull pins can be difficult at times. I coated the tips with some lube. That and a little jiggling seems to solve that issue. I guess it’s better for the pins to be snug vs popping right out. I added a small Master lock to the hitch pin (in lieu of the provided cotter pin) as a theft deterrent. I read that a 3/16 shackle lock will fit into the bike clamp down arms to also act as a deterrent. I had an old 3/16 lock that did snugly fit and appeared to be locked. HOWEVER, I yanked on the lock and it came open as there isn’t quite enough clearance for the shackle to lock. I discovered that longer 3/16 shackle locks are hard to find. Have attached a photo of the lock that actually fits and works (Ace Hardware). One lock on the upper clamp down arm will secure both arms as the lower arm can’t be removed without removing the upper arm. The clamp down arms appear to be coated to prevent damage to your bike. I’ve tried a simple rag and ultimately settled on pool noodle pieces as a precautionary measure. I CAN NOT open my tailgate (regardless of whether or not the rack is fold up and in the bike carry position). If that’s a concern for you, then spring for the more costly titling version. My back-up camera still functions.
The Swagman XTC-2 platform bike carrier arrived very quickly from etrailer and in good shape, the actual carrier box is inside another shipper box, which I'm sure helped with its condition. Assembly was relatively quick and painless, even though the instructions could be a little more thorough. Installing the carrier on the back of our Jeep Patriot also was quick, it helps to have an extra ratchet & 3/4" socket laying around for just this purpose. Installing the bikes takes a little patience and trial and error the first time you try and put them on the carrier. It's easy enough to adjust the wheel holders to fit the wheelbase of your bikes, but for us at least, the challenge was trying to swing the vertical support bar up into position after putting on the first bike (closest to the Jeep). We couldn't angle the bike enough toward the Jeep to have the bar clear the bike. We learned that the easiest way to secure the first bike was to remove the ratcheting frame hooks altogether, put the bike in the carrier, swing up the vertical support bar, put in the pin, and then slide one of the frame hooks down on the bar. The outside bike is much easier because you can set the bike in the carrier at whatever angle you need, not being limited by the back of the vehicle. One thing we did to protect the bike frames was to use some foam pipe insulation as cushion between the frame hook and the frame (see pictures). Once you get a system for installing the bikes, it is very quick to load/unload them. The rack seems to be well made and doesn't wiggle excessively when traveling. All in all a good product for a good price, would definitely recommend it for anyone looking for a platform bike carrier.
# 2
Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount - Black
All in all pretty good. The arms that grab the front wheel have loosened a little bit and move side to side. They have never failed, just feel a little wobbly. The hitch receptacle is also hard to tighten but might be due to the receptacle it self. Used rack on a long trip and the bikes moved slightly side to side, but nothing serious.
Car: 2017 Honda CR-V This is a great rack! There's not a lot to the assembly, other than getting the first two long bolts in, those were tricky. Once those were in there, aligned properly, the rest of the assembly was pretty easy. Attaching the rack to the hitch receiver was the easiest part of the whole thing! The rack is really nicely portable, and will easily store in our apartment during the off season. It takes less than a minute to get it loaded into the hitch receiver. The cable lock is a little bit flimsy, but should hopefully deter casual thievery. What I would have loved to have seen were locks in the retaining arms as well, so those couldn't be messed with by strangers. Otherwise, this rack is really great, and I would highly recommend it.
# 3
Thule Hitching Post Pro Bike Rack for 4 Bikes - 1-1/4" and 2" Hitches
The good: I like the way the bikes are held in and the ability to add the upright adapters to the bike frame holders. The straps are quality too. For a jeep with a spare tire, this is the perfect length to clear it. This rack is 5 stars from the bike holders to the base of it. The bad: the 2"receiver adapter and bolt are insufficient. I wish they made this in a solid 2" hitch. The entire setup is held into the receiver by a very short bolt. It only goes about half way into the receiver tube. So your hitch is only "secured" on one side. A hitch pin or bolt should go through the receiver tube completely imo so it can be secured on the other end with a retaining clip or nut. Because this only goes in the one side, the entire weight of the rack plus bikes are held tight to one side of the receiver by the undersized bolt and washer. A few bumps down the road and that bolt loosens. Now instead of distibuting the weight of the rack and bikes on the receiver and post, it's completely up to the bolt to keep you from losing the rack. The bolt threads get damaged too. I took this down a dirt road and nearly lost everything. I had to buy my own bolt with hd fender washers and lock washers to correct this. Thule should've provided this from the start. The current short bolt design where only one side of the receiver secures the rack is unacceptable. This rack is 1 star at best for the connection to the receiver.
I bought this bike rack back in April but wanted to make sure I used it to give the best review. First I want to say I did a lot of research on bike racks and found this one to be the best one to fit my needs. The best price I found was on etrailer.com, at the time it was When I called the customer service to place my order, I spoke to Dan. He was very pleasant on the phone and took the time and listened to what I needed and understood my concerns. I ordered the bike rack and also ordered the Thule Snug Tite Hitch Lock and Anti-Rattle Device and the Thule Cable Lock w/ One Key System Lock. Dan suggested I also get the Thule Bike Adapter Bar, which I never even thought of getting. Delivery was in about two business days, which was really fast and at the time of order they were running a special free delivery over $99. When I went to put it together I noticed I was missing the flat cap screw M6 x 16mm, part number #853-5787-02. I emailed Dan and within 24 hours received an email that the part was sent out and also in the email their was a link to track the order. After I received the part I did notice that the flat cap screw was actually in the 2 inch adaptor sleeve. The instructions were very easy to read, and it took me about 20 minutes to put together. I did have an issue when I positioned the stinger into the cradle, with the 8mm locking nut, it was not staying tight and when I took it off I noticed the threads inside were gone, so I ended up going out to Lowes and buying a new one and its holds perfectly fine. I also had a question about that part because it is not a locking part and was worried someone would try to steal the rack. I contacted etrailer.com to find if they make a locking device for this and they said no but I can contact Thule to double check, I'm still waiting for an answer back from Thule. The weather finally broke and we installed the rack onto my hitch, tightened it and it doesn't rattle. When I finally used the rack and put my bike on, it did sway a little but at 50 mph I was very happy with it. The trailer comes out just enough away from my car that I do not have to fold completely out and I can open my trunk with no issues. I am very happy with my purchase and had a great customer experience with Dan. Would highly recommend ordering from them to anyone.
# 4
Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount - Gray
I’ve had the Kuat Sherpa for about a year now and could not be more happy with this bike rack. When not in use I keep it safely in the garage- it only takes a few minutes to install it to my Honda Civic and safely secure two bikes using its exquisitely engineered and designed system. I’ve used this for 900+ mile trips with no issues whatsoever - the perfect bike rack!
After doing extensive research before buying my first ever bike rack, I chose the Kuat Sherpa 2.0 platform rack. I considered trunk mounted, hanging and platform racks before settling on a platform rack. I like the stability, the ease of loading and unloading and very importantly, the absence of contact with the frame of my bike. My bike has a beautiful paint job that I want to preserve. I looked at lots of racks online and at a bike shop and opted for the Kuat Sherpa 2.0 because of the excellent engineering, including the design of the packaging that becomes a work bench for assembling the rack, the relatively light weight (32 pounds), the inclusion of a hitch lock and a bike lock, the stability of the platform, even with a 1.25" connection and a class I hitch, and the ease of operation. Additionally, the overall appearance of the rack suggests high quality. Time will tell how well it ages but I'm pretty confident that I'll be pleased with it. I was very fortunate to find a used, like new Kuat via Etrailer at a meaningful discount that still qualified for the manufacturer's warranty! Thank you Etrailer! A tip to pass along that was shared with me, U-Haul is an excellent source for buying and installing hitches to accommodate bike racks - very attractive pricing, high quality installation and a super unlimited lifetime warranty. Can't wait for Spring and the chance to transport my bike to inviting riding venues!! PS The hitch and bike rack work very well with my 2011 Honda Accord Coupe, EXL V6 model that remains in excellent condition.
# 5
Kuat Beta Bike Rack for 2 Bikes - 1-1/4" Hitches - Tilting
I was looking for a light weight bike rack for my 2015 Honda Accord. Your videos stated that the Kuat Beta was light and easy to install. You were right. I opened the box, read the instructions, and had it installed in about 10 minutes. I don't use a rack lock. It is so easy to pop on and off the hitch that I keep the rack in my car trunk.
We've been using this bike rack with a 1.25" Draw-Tite receiver hitch (also purchased from etrailer) on a 2012 Prius C for a month with no problems. As shown on the pictures, it fits two bikes very well, even one with a baby carrier. I chose this model based on recommendations from etrailer that it can be easily detached from the car without tools. True to their word, it is very easily detachable from the hitch and folds up nicely to fit in your garage/closet/storage area. Basically, it uses a hand tightened ball bearing mechanism to secure itself into the hitch receiver, and then uses a 3/8" hand locked pin as a safety device. You can install and de-install this rack in just a few minutes. During driving, there is little noticeable vibration from this rack, even on rougher roads or speed bumps. The only downside is that the holes on the receiver hitch do not align perfectly with the holes on the bike rack (see picture). I believe a few other reviewers also noted this issue. There is enough room to fit the safety pin, but not quite enough to fit a 1/2" hitch lock. I called Kuat to ask them about this and the rep told me that not all hitches will line up with this rack. Kuat, coincidentally(?), sells a hitch lock that is also 3/8" (same size as the safety pin) and still fits.
# 6
Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
Ordered a C11367 trailer hitch for my 3 series BMW, and a Swagman XC-2 Bike rack for use with. Did make a call to etrailer offices for a couple questions prior to purchase, great response and informed input from their rep. Shipment (free) arrived promptly and in great shape. Had a BMW place do hitch install, no issues. Quick and easy assembly of Swagman, really well engineered from both a design and structural perspective. Could not be more pleased with entire experience with etrailer service and product quality. Would highly recommend use of this company and their products. Ron H. North Carolina
I like the overall design of this rack, but unfortunately after hauling a couple bikes around for a while the point where the crossbar connects has apparently rounded off so the rack swings back and forth. I've used rope to tie the ends of the rack to the car to stop this from getting worse, but it's inconvenient. Note: the hitch connection itself is good and solid, but the point where the crossbar connects to the bar coming from the hitch has gotten loose and there's no way that I can see to tighten it.
# 7
Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount - Pearl
I am very happy with my purchase!!! It all began with a pleasant experience contacting Etrailer to confirm that the Kuat Sherpa 2.0 would work with my Class 1 1-1/4" hitch on my 2011 Honda CRV. Roger answered my questions and assisted me with placing my order. I ordered on a Monday and I received it on Thursday in California! It did take me about 2 hours to assemble because I initially tried to follow the written instructions that were in the box. I remembered that several reviewers said that they recommend that you follow the You Tube videos for the Kuat Sherpa 2.0 assembly instructions. Once I followed the videos the assembly was a snap! The bike rack is very sturdy despite weighing in at 35 lbs. I am a 60 year old relatively athletic female and have no problem attaching the bike rack to my hitch! Here's hoping the bike rack holds up for years to come!
# 8
Saris SuperClamp EX Bike Rack for 4 Bikes - 2" Hitches - Wheel Mount - Tilting
This bike rack is a tremendous value. Cheaper and just as good as comparable racks that cost twice as much. The rack has performed superbly. One caution: the manufacturer’s packaging is poorly designed, and insufficient to safely ship a 60+ pound bike rack. The steel parts of the rack shifted during transit and broke several molded plastic components. Saris’ customer service folks were excellent, and promptly sent replacements for the components that were broken in transit. The improper packaging was not etrailer’s fault. Saris should reengineer their packaging for this item.
This is great bike rack. It arrived fast and just in time for our trip in mid July. My husband and I put it together quickly, we looked at a [online] video for how to put it together and went by the instructions booklets. It took us under an hour to put it together. It is very simple to load and unload bikes on it and the bikes stayed stable throughout our 600 mile trip and back. So overall, I am very satisfied with this bike rack. Will now see how it holds up with time.
What our customers are saying:
"Loved the hitch 5-bike bike rack. Came quickly and is as advertised."