Most Popular CURT for 2018 Volvo XC60

Worked perfectly. Super easy installation and it carried a U-haul 5x8 trailer 1000 miles with almost full capacity on tow-limits. A little disappointed that the connecting rod doesn't fit perfectly into the receiver hitch. So, when there is no weight on the ball mount, it is wobbly and makes an annoying metal-to-metal clinking noise whenever you go over a ditch. You can easily correct it with a piece of cardboard stuffing for cushioning or just take it off when not it use. Great piece of equipment, works perfectly! Super happy with the purchase.

This starter kit was exactly the size I needed for the hitch on my Trailblazer, and has held up beautifully this past year. I'm confident it will last for the lifetime of the vehicle.

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.

I purchased this ball mount as it was the one etrailer specified for use with the Curt receiver I purchased for my Volvo XC60. The product arrived in perfect condition and sooner then promised.

Excellent hitch easy installation.It only took me about an hr and half to install from start to finish

Very happy with hitch and components, came in a nice tray that I use to store and organize the parts when not in use in the back compartment of my Telluride. All good.

I have two of these. My first I bought two years ago. I very highly recommend this Curt Class III Ballmount 2" Drop because of its price, durability and quality. I towed various class 3 loads with ease and confidence with this ballmount. It slides into the hitch and does its job without fail. It looks excellent after towing a load. etrailer's price is about as good as it gets and delivery is very speedy.

The hitch and ball mount are excellent quality. My concerns are twofold. The hitch is so heavy that I had to take it to my mechanic to have it installed. Minor cost and inconvenience, but the hitch for my previous F-150 was just as sturdy, but easy to install myself (albeit with higher ground clearance). My concern about the ball mount is that the factory told me erroneously that it could not be reversed for a drop, so I returned it. This order is for the replacement after I was finally correctly told it could be reversed and how to do that. Ball mount would have been a 3 for that reason, and overall hitch and ball mount quality a 5. So I averaged them.

Hitch is solid and install was 2 hours

Here's 2 photos of the finished product. Doesn't stick out very far which is fantastic, because it definitely would have looked bad on the back of a 2 door coupe GTP. As for installation, being a mechanic, all I had to do was remove 2 rear exhaust rubber hangers and the one right behind the fuel tank, lower the exhaust onto a set of jacks to support the weight. Then drilled 2 1/2" holes with a 90 degree drill. The coiled wires included with the parts saved me tons of time trying to get the bolts in. Overall, it was fairly simple to install. Torquing the bolts proved a little difficult. I would recommend you inform the customers that they'll need at least a 10" eye to eye reciever (I have the 11" one on mine) in order to clear the rear bumper and provide some space between the bumper and trailer tongue. As for the wiring, I cut a small slit in the rubber plug under the spare tire, ran some bulk trailer wiring up through it, under the tire, under the floor matting, to the right side of the trunk, behind the tail light. And up under the lid on the right side, is the tail light wire harness/connector. Test light confirmed which wires were hot, tapped into them and all the wires and lights are good to go. Just some extra info for the DIY'er that might be handy on the website so they won't have to search for it! Couldn't be happier with the hitch.

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

Works great solid product.