# 1
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Bolts for the 2 tabs need to be 1/4” longer.
One of the side vertical mounts on the hitch was pretty bent out of th box. Put it in a vise and straightened it out. Definitely remove the grill and spacer at the bumper to work from above, Drivers side is still 1/4” away from the frame. Use the smaller shims included to fill the gap perfectly. 2012 you need to run a drill bit through the lower driver side mounting hole to get the bolt through. With the shim in place the included bolt for the drivers upper hole is to short so grab a longer one for this hole only. Need to remove that booster thing from the frame to get a socket on the upper left mounting bolt. All this takes a lot longer than expected but it’s solid as a rock.
# 2
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
We bought this hitch to use a floating snow plow on the front. It's works just like it should.we took our bumper off to put a new aftermarket bumper on which made installation easier. With an aftermarket bumper we did have to trim a part in the middle of the bumper for the hitch to fit but if you have a stock bumper it will fit perfect.
What can I say that you haven't already heard? etrailer.com made this such a painless and straight forward process for selecting the front hitch for my 2015 Jeep Rubicon Unlimited that I can't believe I didn't do it sooner. The Curt front hitch for my jeep arrived quickly and in great shape, very well packed. On unpacking I found my hardware and instruction firmly secured to it so it didn't get mixed up with my rear hitch, good forward thinking. The hitch is robustly built and you can see the care that goes into the quality, all the welds are neat and tidy and the finish is excellent. The hardware is all coated for long lasting performance and the fish wire is beyond handy. For the installation of the front hitch the instructions are a little lacking. This is not to say bad or confusing, just lacking a little more how to. The etrailer video on installing it made the process go smooth and easy. On my Rubicon model you do have to fight with the sway bar motor on the passenger side and the vacuum unit on the driver side, it is a pain but if you take the top frame trim off it is much easier to work. The bolt hole on the drivers side, pass a drill through it to make sure the ft is right because its very tight to work in that area and close won't work. Other than that, it installs exactly like the video. The only thing that would complete the package would be a template for clipping the front plastic shield, the Curt instructions include a sketch that gives you an idea but a simple temporary adhesive template would make it super simple to drill the corners out and then connect the dots with a tool of choice. But hey, that's just me. The hitch tucks up real nice and doesn't kill approach angle or ground clearance which is great for my application as its for carrying a winch when I need it. I would recommend etrailer.com without hesitation and strongly urge the Curt line of products based on what I've seen so far.
# 3
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Directions were clear and concise, however the side brackets were slightly narrower than the vehicle frame and it needed a fair amount of convincing to slide up and over into place. Furthermore the driver side superior bracket hole was offset just enough not to allow the bolt to pass through the frame. The hole in the frame had to be slightly enlarged. Otherwise it looks great!!
By the way, are tongue weight and vertical weight different measurements??
# 4
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just received the front mount hitch receiver from eTrailer, haven’t installed but can tell it’s a quality item. Extremely impressed with eTrailer’s packaging technique to stabilize the receiver in the box for shipping. They have devised a system to hold the hitch assembly completely stable inside their heavy duty box to keep the heavy hitch from busting through during shipment. The complete assembly arrived without a scratch even though the shipper did manage to make some holes in the box. Excellent work eTrailer and first scratch on my receiver happens tomorrow while I am installing. My scratches are OK and hold my memories, but I don’t like other’s inflicting harm.
ordering was simple and straight forward . No drilling involved installing it and fits perfect and looks good ..
# 5
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
# 6
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Ordered the same hitch from Amazon, and showed up not J-Pin ready, with (1) hole drilled for a hitch pin against the weld. Can't run the nut flush because of the interference with the weld bead, and no 7/16" hole present. Returned it. Ordered another one from etrailer direct. Called in the order to make sure they QC'd prior to shipping. Assured me they would. Box never opened, and the same nonsense showed up. Not happy, trying to work it out.
Fit Perfectly, super easy to install, and super fast shipping! Holds Hollywood Bike Rack Great and very solid for my two E-bikes. Thank you etrailer!
# 7
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I was looking for. Thank you.
I ordered these two, front and rear for a 1990 GEO Tracker 4 wheel drive that I am rebuilding. I believed they would fit, I finally got around to mounting them and they don't fit, to large. I think I have had them to long to return them.
# 8
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Easy installation, nice sturdy hitch that fits on the front of our C- Class RV to haul our electric bikes. Highly recommend it.
I ordered this literally less than 24 hours ago and it arrived to my doorstep!!! I think etrailer needs to call Amazon and tell them how it is done. Like honestly, I am not even prepared to put it on yet as I was expecting a week for delivery! Holy cow, do you all sell groceries as well?
# 9
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I went with this hitch since I have an after market front bumper. I wasn’t sure if it was going to fit but since this hitch was a bolted connection it gave me 2 options to have a chance it would fit. One I received the package the box was damaged but all the hardware had been taken to the hitch, so everything was there. I installed the hitch by myself and took me about 2 hours but that was due to the aftermarket bumper and dealing with that hardware at the same time otherwise the install went smooth. Tha last phot is to show this hitch worked with this bumper.
Mounted this hitch about a year ago and really like it. We pull a fifth wheel camper so this affords us the ability to haul our bikes or kayaks(tall T stand) up front. Was easy to install and looks good to boot.
# 10
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitched arrived three days early and I was able to install it in less than 2 hrs with a little help from my wife and a floor jack. Perfect fit!! No shimms necessary Vwrry happy.
The hitch installed easily on the front of my truck and has given me more versatility in using my truck. In the summer I carry 3 bikes on a hitch rack when I go camping. I also hook up a 12000 lb. winch when needed. Sometimes I use the front hitch when moving my boat. This is a very sturdy and reliable hitch. Etrailer customer service is excellent.
# 11
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
The hitch came packaged in a double box. The outer box had some damage but the hitch did not. I read the instructions, making sure i had the correct tools, and jacked my truck up. The install took three hours as i was layiing on my back with simple hand tools. The parts all fit and i am happy with the outcome. Good price, simple instructions, good fit.
Excellent product. Always pleased with Curt products. Quality built with easy to install video provided by etrailer. Shout out to Alex at etrailer for getting me the exact fit for my 2007 Chevy Silverado. Good job etrailer. Received with 4 days of order placement
# 12
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Needed a front hitch for a 2006 Ridgeline Honda truck. I found it on etrailer.com and a better price for same hitch on another online store. As I talked with the customer service agent, I was also offered a discount which was quite a surprise. Shipping was very fast. Had it installed on my truck so I could attach a mounting hitch and snow blade. I am extremely happy with this hitch and etrailer.com.
We live just south of Buffalo and Put this on our '11 Honda Ridgeline with a snowsport plow and a week later it snowed, and snowed and snowed... 5 feet in 24 hours and it's still snowing.... It's not good.... It's AWESOME! Not one driveway or even our street is clear... Except ours. It was easy to put together , easy to install and works exactly like it's advertised! It's November and it paid for itself already. Communication with etrailer was exceptional. We could not be happier with the whole setup.
# 13
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great products, great prices, fast shipping and a great company to do business with. Easy install, and it took longer to trim the air dam than installing the hitch.
I have had this hitch installed for just over a year now on my '99 2-door Tahoe. The install was pretty straight forward, and the hitch itself has held up quite well through a year's worth of abuse. I use it to run my bike rack out the front; the receiver protrudes just below the factory front bumper, maximizing ground clearance when adding length to the front of the vehicle. And as you can see, the kit comes with two sets of hardware in case you want to maintain the factory tow hooks like I have.
# 14
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I chose Draw-tite because they are built very well and this one is no different. The welds are done well and I have no fear that this product will serve me well. The install wasnt to bad for a DIY type like me and the fit was excellent, only took a few hours. Knowing that I can now be pulled out of a bad situation or pull someone else out is comforting with the help of a hitch mounted winch. The Price was right and etrailer shipped it out fast although packing could use a smaller box . Oh yeah, UPS sure tested the toughness of this receiver ! . Great product and great service from etrailer
im very satisfied with my front receiver. ive used it as a recovery point,to move trailers, and as a mount for bike rack and cargo holder. if i had a winch platethat would be very handy too. etrailerhad a fair price, quick shipping, and overall great customer service. i would use them again andrecommend to a friend as well.
# 15
EcoHitch Hidden Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Just what I needed. The hitch fit perfectly, all parts were there and the installation instructions were very clear.
Fit nice. I haven't used it to move a trailer yet. I didn't have tow hooks and the factory ones are high so I paid the extra to get the hitch instead.
# 16
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Great customer service and product.
The quality and fit is exceptional. So much so that this is the third hitch assembly I've purchased and installed. This one was for my brother in-laws 1999 F350. I also put a 10k winch on a slider that works perfectly with this assembly. Other vehicles I purchased and installed assemblies on are a 2011 F350 and a 2016 Class C motorhome. Very happy.
# 17
Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
How it was received; either is was mail destroyed or UPS did this in the process. No telling what parts are missing, waiting for UPS to come pick this and E-Trailer to send out replacement. I thought these product would be packaged better from the factory for shipping resilience.
Of the many hitch receivers I have purchased, the front mounted ones have never failed to surprise me of their usefulness! From bike racks, to carrier for coolers, to my chainsaws, gas and oil, they make it work. Recently while cutting wood for a hunting lease engagement, I put a second ball on the front and used it to drive a 16' trailer up a hill to get the wood where it was needed for offloading. Backing it up had resulting in damaged trucks, trailers and numerous attempts. Using the front hitch it was a one and done deal! Love it! I have even used it to pull trees over when felling. I don't have enough fingers and toes to count the uses! If you have ever thought about it, just stop and order! You won't regret it!
# 18
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
After a year of having this on my truck I can say that I wish I did it sooner! The installation is easy as can be. The hitch is super handy as both a tow point and also as a kind of skid plate/bumper. I have contacted multiple ecology blocks and other objects in my truck, the hitch is the first thing to touch so nothing on the truck gets damaged! This is a super strong, affordable, and versatile addition to any vehicle!
VERY Easy install - not quite centered but that's no biggie - Used it already to fine tune the travel trailer into it's tight parking space. Also will be used for carhauler/utility trailer parking and canoe hauling and bike hauling and winch mount - Multi use deal! ; )
# 19
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
Road tested 4000 miles & off-road, Solid, Great ! I always wanted a front hitch, it is rad ! We had a great experience across the board. Ordered the front hitch mount and had a mechanic (Weld Tech/San Diego) install it, because they already had our van to install their lift kit. They charged me one hour labor. I can see that it fits well and is solid. We went on a 4000 mile adventure with a small motorcycle on the front hitch. etrailer has been a good source for for a few things now.
I own a 2003 Ford E-450 RV cutaway and wanted a front hitch to carry our bicycles since our rear hitch is used for a trailer. I originally tried to mount the equivalent Curt front hitch, because of its cheaper cost, onto the vehicle. However, the Curt hitch wouldn't work because it can't adequately accommodate the slight downward hump in the truck's frame. This hump can barely be seen between the two hitch mounting bolts. The hump is on both the left and right side frame rails on my vehicle. If your frame is not totally flat (has even a small hump) you cannot use the Curt hitch. The Curt's small indentation on its mounting flange will not adequately accommodate the frame's hump. This Draw-Tite hitch, 65001, mounted perfectly on my vehicle and the installation procedures I used were exactly as depicted in the etrailer video for the E350 van. In the video, the technician uses a rotary file to expand the rearward holes to allow the insertion of the bolts. I had to do the same thing and bought a rotary file for my drill at my local home improvement store for less than $3. I did not have to use the rotary file on the forward holes. In addition, I have the larger Roadmaster front sway bar and steering stabilizer and as you can tell in the photo, there is plenty of room for the hitch.
# 20
Draw-Tite Front Mount Trailer Hitch Receiver - Custom Fit - 2"
I buy practically all my towing accessories from etrailer. One of the reasons why is that you can tell that they take the feedback of their customers seriously. I read a lot about previously shipped products having fell out of the box in certain areas. etrailer heard that feedback and my shipping box was reinforced in just the right areas that were talked about getting punched through in shipping. The tech notes video on the 2012 F-250 applied exactly on my 2016 F-250. All the measurement specifications were correct as well. This is a job that can be done by one person, albeit you'll have to be careful. Your second set of hands can be jack stands, as it was in my case. If you take your time in positioning everything - installation will be a breeze. I do agree with previous reviews - it would be nice to have a second fishing wire as it does get stretched out when pulling the first bolt through. That, or a heavier duty gauged wire - that's just a small detail however. If you're really concerned about it, you can buy a secondary fishing wire at around 5 bucks. I spent more time taking out and putting back in body clips than I did with the install of the hitch receiver hardware. I really like the way it looks and I'm excited to use it.
I plan on installing it tomorrow, however first impressions are not good. The box it item was shipped in was extremely damaged. Torn, ripped and taped up on all sides. The delivery person said that due to the sharp edges and the face it wasn't secured in the box (lose) led to the damage. It appears the item was not packaged properly. I just hope all the parts are there. More to follow.
What our customers are saying:
"Received already. Yeow! Perfect fit. Thanks for getting the kit to me so quickly."