Most Popular Fixed Ball Mount for 2013 Hyundai Santa Fe

2nd order from etrailer, great customer service & fast delivery! My 2" ball fit the ball mount perfectly and I installed it in a few minutes. Make sure that you use a ball with a 1" shank. It stores easily underneath my Hyundai Santa Fe cargo mat until I need it.

My order arrived in two days. I am impressed both by the layout and functionality of etrailer website and by the quick, free shipment. The hitch for my 20007 Hyundai Santa Fe is well made, well finished and fit perfectly. The estimated installation time of 30 minutes would probably have been accurate had I not had to clean 3 years worth of rust from the mounting nuts installed by the factory. Once clean (no simple task since reaching them with a 10m/1.25 tap was difficult) mounting the tow bar was simple and made easier with a pair of jackstands. Owing to the design and location of the mounts, reaching them required the use of different ratchet extensions and flexible joints and I'm not certain of the accuracy of any torque reading. In summary, I am pleased with the product and impressed by the follow-up from etrailer. I will recommend them without hesitation.

E-trailer’s website made it easy to find the correct trailer hitch for my 2019 Santa Fe. The videos on the site shows the easy installation. Great products and great assistance where I needed it. Thank you.

The good: It works. The not so good: 1. The lock washer on the ball stud makes it really hard to remove the nut. The lock washer cuts into the nut, essentially preventing it from unscrewing. This is good from a safety standpoint, but makes changing the configuration really hard. I had to lock it into a bench vice and use a pipe wrench to get it off. 2. Not sure what happened, but first time I used it (to pull a rental trailer), the hitch pin fell out, causing the trailer to disconnect. Best I can figure is that the cotter pin popped off. Fortunately, I wasn't on the highway, and the safety chains kept the trailer attached. But it was pretty scary. I replaced it with a locking pin, and had no further issues.

was easy enough to install with the factory tow kit on my 17 Hyundai santa fe. Instruction pictures and installation video show ground (White) wire is connected to one of the electrical connectors. This was not the case as mine came with the white wire hanging loose, easy enough to install a ground connection to the frame as I did not know how to open the electrical connectors to attach the ground to the actual plug.

Product arrived but was missing pin and clip...Call customer service over matter and was told they will send

Arrived right on time in excellent condition. All instructions were straight fwd. Could not have been any more detailed. Excellent product and outstanding service, my compliments. Fit our 2017 vehicle without a "hitch"! Ordered hitch and ball with this, but was not aware that the pin for the hitch was not included, my fault for not checking. Thanks for the excellent product and service. Jack R.

Quality product.

To be honest, I use it upside down. I needed a hitch with rise, but none were available at time of purchase, and yours, inverted, works perfectly! The welds are regularly checked and remain all secure. It's a good hitch.

Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done. Now we can pull our Sunfish Sailboat any where the car will go.

Very pleased with etrailer. Very easy to order from website. Fast delivery, easy to install ,perfect fit . Thanks. .

Perfect fit for 2 inch Draw Tite receiver. good price, fast shipping.

etrailer has what you need

I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.

We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack. The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.

This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.

Excellent product! With the three different ball sizes, this tri-ball mount gives you a lot of flexibility. Gone are the days of having several different ball mounts to fit different tongues. High quality construction makes this an excellent investment.

This item should solve the problem I have had with a stainless 3-way ball when I tried to reverse the position on the ball mount. The threads galled between the hex nut and hitch ball.

This was a very easy installation. The custom fit design was exactly what I wanted. Wife and I installed it ourselves. Saved us hundreds of dollars and it looks professional. The video was very well done. Thanks etrailer for having these products available. We will definitely be using your services again!!!

I bought the 1 7/8 and 2 inch combo so that switching between the two is as easy as pulling a pin. However, I didn't realize that I had to install the ball. I had to find someone with a wrench and torque wrench big enough to do it. Otherwise, excellent quality as usual from E-Trailer.

Works as advertised. Great fit and now my boat is level traveling down the road. Fast turn-a-round. For [xx] shipping and the heavy weight, expected delivery in a week or two. Two days later it was at my doorstep, arriving late evening. Great service. Thank you.

I ordered the product as stated below and I received it in a couple of days. It is made well and fit into my hitch on my 2006 Santa Fe perfectly. I would recommend this company.

I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.

We used our car hitch and cargo carrier last summer in a Honda Accord to support a cargo carrier. It held up great on a 4,000 mile camping/hiking trip from Mid Missouri to Glacier National Park, MT. We were able to use the carrier/hitch to carry our large tents and baggage (approx 120#)directly behind our car trunk. Initially I was a little hesitant at the smaller 1-1/4" tube hitch, but it was very stable throughout the long trip. Sure was a lot less drag than putting all our gear on a roof cargo carrier.

Overly tight on the receiver end bit functions as intended.

I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.

The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.

Works great solid product.

Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .

Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks

Love these. This is my third one. Wouldnt pull a trailer with anything else. Trannys are expensive.

As a full-time RVer, e-shopping is very important for us. etrailer was the right place to shop. Right product, delivered on-time for a great price. You beat the local discount RV store by $25 including shipping. At the same time, I had another outfit send me a clearly inferior product to the one they displayed. Said they would e-mail a pre-paid shipping label for the return (didn't) and tried to put the blame on Amazon. Thanks etrailer for a great experience !

Great internet page with everything you need to know before buying! Bought hitch+tongue+ball+wiring connection. Great products, great price, realy fast shipping! Would buy anytime again!!

Thank you etrailer for the quality products I received early last year. We needed a trailer hitch to install on our Subaru Forester for our move from Gig Harbor, WA to Spokane. We received the hitch hardware including the tow bar and electrical harness. The entire process took 4 hours. The installation process went off without a hitch (bun intended) using detailed videos I found online. Thank you etrailer.

Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.

Great customer service. Live in SC - ordered a hitch and USPS delivered it to PUERTO RICO. Go figure. Stacey A refunded my money - but 2 weeks later hitch appeared on my doorstep. All’s well that ends well.

works well brings the trailer tongue up to level. I have it on an EV so the raddle is annoying, because I just keep on forgetting to buy a anti rattler.

This is very sturdy hitch. It is made of solid steel, not tubing. It will be used on my Mazda RX-3 to tow my car dolly to the RV lot where I will swap everything around and the car will end up on the dolly behind my RV.

This is really nice. Beveled edges so it slips into receiver hitch so sweet. Beautiful welds heavy weight mount for my weigh safe ball. I bought a 10,000 lbs hitch and I wanted a draw bar with the same type rating. Now the only thing limiting my trailer capacity is my truck's ability to tow, not the hitch, bar or ball.

I purchased a Ranch Hand rear bumper for my 2500HD but wanted to retain the use of a receiver hitch. The ball mount would need to extend 8" from the pin hole to even reach the edge of the bumper. This BM29 ball mount works out perfect. The welds look great and the finish is just fine. The only complaint I have is they gained a little length by moving the pin hole a little closer to the end shortening the insertion amount slightly. Not a big deal, it is just noticable next to the other mounts I have at the house.