# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
2nd order from etrailer, great customer service & fast delivery! My 2" ball fit the ball mount perfectly and I installed it in a few minutes. Make sure that you use a ball with a 1" shank. It stores easily underneath my Hyundai Santa Fe cargo mat until I need it.
My order arrived in two days. I am impressed both by the layout and functionality of etrailer website and by the quick, free shipment. The hitch for my 20007 Hyundai Santa Fe is well made, well finished and fit perfectly. The estimated installation time of 30 minutes would probably have been accurate had I not had to clean 3 years worth of rust from the mounting nuts installed by the factory. Once clean (no simple task since reaching them with a 10m/1.25 tap was difficult) mounting the tow bar was simple and made easier with a pair of jackstands. Owing to the design and location of the mounts, reaching them required the use of different ratchet extensions and flexible joints and I'm not certain of the accuracy of any torque reading. In summary, I am pleased with the product and impressed by the follow-up from etrailer. I will recommend them without hesitation.
# 2
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
E-trailer’s website made it easy to find the correct trailer hitch for my 2019 Santa Fe. The videos on the site shows the easy installation. Great products and great assistance where I needed it. Thank you.
The good: It works. The not so good: 1. The lock washer on the ball stud makes it really hard to remove the nut. The lock washer cuts into the nut, essentially preventing it from unscrewing. This is good from a safety standpoint, but makes changing the configuration really hard. I had to lock it into a bench vice and use a pipe wrench to get it off. 2. Not sure what happened, but first time I used it (to pull a rental trailer), the hitch pin fell out, causing the trailer to disconnect. Best I can figure is that the cotter pin popped off. Fortunately, I wasn't on the highway, and the safety chains kept the trailer attached. But it was pretty scary. I replaced it with a locking pin, and had no further issues.
# 3
Curt Class III Ball Mount with 2" Ball - 2" Drop - 7,500 lbs
was easy enough to install with the factory tow kit on my 17 Hyundai santa fe. Instruction pictures and installation video show ground (White) wire is connected to one of the electrical connectors. This was not the case as mine came with the white wire hanging loose, easy enough to install a ground connection to the frame as I did not know how to open the electrical connectors to attach the ground to the actual plug.
Product arrived but was missing pin and clip...Call customer service over matter and was told they will send
# 4
Curt Ball Mount for 2" Hitches - 1" Rise, 2-1/4" Drop - 7-5/8" Long - 7,500 lbs
Arrived right on time in excellent condition. All instructions were straight fwd. Could not have been any more detailed. Excellent product and outstanding service, my compliments. Fit our 2017 vehicle without a "hitch"! Ordered hitch and ball with this, but was not aware that the pin for the hitch was not included, my fault for not checking. Thanks for the excellent product and service. Jack R.
Quality product.
# 5
etrailer Ball Mount Kit - 3/4" Rise or 2" Drop - 7,500 lbs
This was a very easy installation. The custom fit design was exactly what I wanted. Wife and I installed it ourselves. Saved us hundreds of dollars and it looks professional. The video was very well done. Thanks etrailer for having these products available. We will definitely be using your services again!!!
I bought the 1 7/8 and 2 inch combo so that switching between the two is as easy as pulling a pin. However, I didn't realize that I had to install the ball. I had to find someone with a wrench and torque wrench big enough to do it. Otherwise, excellent quality as usual from E-Trailer.
# 6
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
I hooked up the draw bar today for the first time to the trailer that I built and the hitch I installed. The draw bar uses a cotter pin that slides on the bolt rather than going through a hole to mount the bar to the hitch. I have never used a sliding on pin in anything - I've only used those that go through a small hole matching the pin. This includes my farm tractor and other tools. I hope it is secure because it does slide on easily. The bar itself appears nice and strong.
We used our car hitch and cargo carrier last summer in a Honda Accord to support a cargo carrier. It held up great on a 4,000 mile camping/hiking trip from Mid Missouri to Glacier National Park, MT. We were able to use the carrier/hitch to carry our large tents and baggage (approx 120#)directly behind our car trunk. Initially I was a little hesitant at the smaller 1-1/4" tube hitch, but it was very stable throughout the long trip. Sure was a lot less drag than putting all our gear on a roof cargo carrier.
# 7
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Retail type stores only carry mainstream items so when I needed a special length ball mount for my 2011 Traverse I found the size and quality with Curt Products .
Recently bought a Kubota RTV x900. The receiver is located under the bed. With the extra long ball hitch drawbar I can easily get to the drawbar and use a clevis to hitch my 5ft. wide mower or attach a ball and use the trailer. The pictures will illustrate the length of the drawbar which makes access very easy. The product is heavy duty and well made. Ordered this product on Thursday morning and it was delivered the next day, Friday afternoon. Customer service was helpful, will use etrailer again. Thanks
# 8
etrailer Ball Mount Kit for 2" Hitches - 3/4" Rise or 2" Drop - 7,500 lbs
Great internet page with everything you need to know before buying! Bought hitch+tongue+ball+wiring connection. Great products, great price, realy fast shipping! Would buy anytime again!!
Thank you etrailer for the quality products I received early last year. We needed a trailer hitch to install on our Subaru Forester for our move from Gig Harbor, WA to Spokane. We received the hitch hardware including the tow bar and electrical harness. The entire process took 4 hours. The installation process went off without a hitch (bun intended) using detailed videos I found online. Thank you etrailer.
# 9
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Very happy with this ball mount - provides just the amount of drop we required for a level tow of our GeoPro travel trailer by our RAM2500. Plus, the extra length not only allows a tighter turning radius, but also allows us to lower the truck tailgate without having to detach the trailer. Huge improvement on all accounts for us compared to our prior setup. The product is well built and I'm confident will provide us years of good use.
Great customer service. Live in SC - ordered a hitch and USPS delivered it to PUERTO RICO. Go figure. Stacey A refunded my money - but 2 weeks later hitch appeared on my doorstep. All’s well that ends well.
# 10
Draw-Tite Ball Mount - 3/4" Rise, 2" Drop - 10-1/2" Long - 6,000 lbs
The shipping was quick. I've also owned it for a year and the product is solid. Besides the sticker wearing, the hitch is perfect.
Excellent service. Fast delivery. Very Satisfied.
# 11
Brophy Ball Mount - 1" Rise, 2" Drop - 9-3/4" Long - Aluminum - 8,000 lbs
It was exactly wat I needed when I looked at the measurements with and aluminum construction looks great.
Very nice ball mount. Smooth, one piece design. Unlike my previous ball mount, it's long enough (enough straight length between the pin hole and the beginning of the bend) to accommodate a Blue Ox Hitch Receiver Immobilizer II, yielding a nice, tight connection. Attractive polished finish. Made in Taiwan (according to the box it came in). Photos show it attached to a Hidden Hitch Class III Hitch Receiver, secured with a Blue Ox Hitch Receiver Immobilizer II, and a Curt 40053 2-inch stainless steel ball.
What our customers are saying:
"You folks are fast. Thank you very much."