# 1
Hopkins 7-Way RV Style Connector with Molded Cable - Trailer End - 8' Long - RV Standard
Just what I was looking for. I needed a heavy duty pigtail for my towing situation and this fits the bill. Only way it could be better is if I could order a custom pigtail with molded plugs on both ends.
Çable good but after putting new 7way plug on truck cable wire colors did not match etrailers picture
# 2
Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End
Sooo, bought another one to match my truck side connection as GM uses Pollak, which are known to not play well with other brands. The design is just a wire clamp to wire it, which I did with the first one, but trying to get it secured I stripped out the screw. There are no torque specs provided. I’ll move to crimped ring terminals on this one and dial back the torque a bit.
Routine trailer maintenance. Absolutely nothing worse than fighting trailer lighting or electric brake issues when traveling.
# 3
Hopkins Endurance Multi-Tow 7-, 5- and 4-Way Flat Trailer Connector - Vehicle End - Ergonomic Design
Works great and etrailer folks did an outstanding job with quick turnaround and communication…thank you!
Exactly what we had been looking for. Now I can hook up multiple trailers with different connectors and all the electrics on each trailer works. I mounted mine directly to the receiver hitch frame. The biggest challenge for us was routing the backup wire from the taillight housing, through the body of the truck to the connector. the rest went together fairly easily. Seems to be pretty solid and looks much better than the loose pigtail connector it replaced.
# 4
Pollak 6-Pole, Round Pin, Plastic Trailer Wiring Socket w/ Rubber Boot - Vehicle End
This part is an exact replacement to the part that failed. The failure was caused by a poor installation which allowed the rubber boot to chaff on the truck frame. As it was an exact replacement installation was straight forward although I modified the mounting bracket to prevent a reoccurrence of the problem.
I found what I thought I needed on the website to prepare our car to be flat towed, but wanted to call to verify. After a short phone call, eTrailer saved me about $50 and got me the stuff I actually needed to get the job done! I won’t shop anywhere else!
# 5
Hopkins Endurance 7-Way Trailer Connector Socket - Vehicle End - Ergonomic Design
This receptical is exactly what I needed to build my custom towing connections since it wasn't factory prewired.
GREAT QUALITY AND RELIABILITY!!!
# 6
Pollak Heavy-Duty, 4-Pole, Round Pin Socket, Concealed Terminals - Chrome - Vehicle End
Items were simply “thrown in the box” WITH the hitch which was not secured properly. Heavy hitch then bounced around on electrical connectors, destroying them. Components should have been fastened to the hitch as the hardware kit was with strong tape instead of just thrown into the box by somebody! Refund issued.
Product arrived on time and as described. I used this for setting up our 2014 Wrangler Unlimited Sahara for a flat tow. Mounting hole spacing @ 2" o/c didn't match our Blue Ox 1126 draw bar so I fabricated my own intermediate bracket, polished it to aircraft tooling standards, then lacquered it before final assembly. I think the finished product came out nice.
# 7
Pollak 6-Pole, Round Pin, Trailer Wiring Connector - Trailer End
Quick shipping, will order from them again!
Exactly what I needed and It's a great fit
# 8
7-Way Molded Trailer Wire Connector, 4' Long
When I ordered this harness I thought I was getting a standard 7 way for a conventional trailer with brakes. What I actually got was a harness made for a camper/RV hook up. The wires have all the colors you would expect but all the lights/turn signals are coded into the plug completely different. After spending a good deal of time carefully matching, soldering and heat shrinking all connections to my new trailer harness, I was very dismayed to find only the brakes actually worked. After a bit of research I found a schematics page on the etrailer site and discovered the problem. As this is a molded plug I could not take it apart and just reposition the wires inside the plug. Another full hour or more of rewiring followed and now all is well. The harness itself is of very good quality but was not labeled/identified properly. This could have been prevented if etrailer would clearly label this harness as a camper/RV harness only.
This is definitely a good quality molded cord for the money. Route and wire this cord into a good quality junction box and you will be on your way to having some excellent trailer wiring.
# 9
20 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 30" Ground
Wiring worked perfect for my project. I replaced the wiring on my 14 foot utility trailer. If I was to do it again I would buy the next length up. I would have liked to have a little extra wiring if I was to ever need it.
Your sales staff is second to none. Keep up the good work. You shipped minutes after I placed my order! Very impressed! Marty
# 10
Trailer End Connector - 4-Flat - Coiled
GREAT ACCURATE REPLACEMENT WIRING.
Timely shipment. I’ve bought from your company before and haven’t been disappointed. Nice job.
# 11
Pollak 6-Pole, Round Pin, Trailer Wiring Socket - Vehicle End
Excellent Quick Delivery When you are driving a Test or NASCAR Hauler you need replacement parts very quick, just like a pit stop. Thank You very much for the rapid delivery. Mint Moore III Ford Performance Race Hauler Driver
A great little heavy duty plug that I use to connect my car to the rv when towing 4 down.
# 12
RoadMaster 4-Wire Connector - Vehicle End
These 4 wire round connectors look quite robust and are priced right! Shipment was super quick. etrailer is the best!
We just finished a makeover of our 1995 boat trailer. New bunks, sanded and painted but the best part of the project was the new LED lights from your company. They are so much brighter than the old incandescent bulbs that you really do feel safer driving down the road. We pulled the 20 year old wire out and replaced with new and used the 3M scotch loks to tie in. We were not sure the new style grommets would fit the old holes in the frame but they fit great. Your customer service was great, alerting me to a backordered reflector but recommended a replacement that worked fine. Patrick set up a Q&A page for me since I had questions about the best way to protect connections with dielectric grease, heat shrink and tape. Your website is one of the best with ease of navigation, complete pictures, great selection and thorough info, dimensions, etc. You guys really have your act together and also offer great value. I would not hesitate to purchase again and will recommend you when I can. I have attached a couple of pictures. Thanks for all your help. Wayne N.
# 13
Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket - Vehicle End
It is a direct OEM replacement, easy installation. What I liked most was a real person answered my call and took my order, Katherine was very polite and knowledgeable. Thanks again. CJ
Worked out awesome. I bought this for a buddy for his used truck. The previous owners for what ever reason took it. Plugged it in and worked flawlessly.
# 14
Hopkins Endurance 6-Way Trailer Connector Socket - Vehicle End - Ergonomic Design
The stuff not here
Very difficult to make the wiring connections, I was afraid I’d have problems on down the road so, I took it out of circuit and threw it away
# 15
Pollak Heavy-Duty, 4-Pole, Round Pin Trailer Wiring Connector - Metal - Trailer End
Great place for any trailer needs. They alway gave what I want at a good price and fast shipping.
Just what we needed to make a custom harness for our boat trailers that we often tow with light and medium-duty wreckers. No more zip-typing our wireless drag lights to the trailers! Thanks, guys!
# 16
35 Ft 4-Way Trailer Wiring Harness - Wishbone Style - 42" Ground
Replaced the wiring and lights on my 1992 boat trailer. I was able to get everything needed from etrailer. I think Optronics is of the highest quality and recommend both etrailer and Optronics product.
Works very well after re-wiring trailer lights with waterproof distribution box.
# 17
7-Way Molded Trailer Wire Connector - 3' Long
I've had this in use for over a year and they don't build them like they use to. I use this on a gooseneck trailer and the piece of plastic behind the spade connector for the clearance lights and brakes has melted, allowing the spade connector to lose contact with the plug on the pickup. So the lights would cut off in the middle of the night and would have to wiggle the connection till I could fix it. I have an older Hopkins plug and never had this problem. To fix the problem I ended up putting pieces of thin copper wire behind the spade and have done it twice since the plastic melted a 2nd time and once again the trailer clearance lights would quit working. Attached are before and after pictures.
After a year doing its job well.
# 18
Hopkins Endurance 4-Way Flat Trailer Connector - Trailer End - Ergonomic Design
I rewired my light bar for my boat trailer with the items I purchased. Before I built the the light bar, every time I used my boat trailer I would waste valuable sailing or fishing time repairing faulty lights. The do not last long when you submerge them in salt water. This light bar now version 3.0 have given little trouble over the years
Great product. Works well when I had a broken connection on my 4 way plug end on my light-up hitch cover I bought from y'all a while back. Always a happy customer. Thanks, George.
# 19
Pollak 9-Pole, Round Pin Trailer Socket - Vehicle End
Looks great. Problem is I need to return this because I can not find 9 wire cord.
Fast service and great price for a great product. I choose etrailer.com instead of fleetpride? now. They just have it all! Thanks
# 20
25 Ft 5-Way Trailer Wiring Harness - Wishbone Style - 30" Ground - 5' Auxiliary Wire
So, I converted my brand new Loadrite trailer to LED'S and wanted to add up a reverse light. I purchased this 5 wires trailer light harness to do the trick. Very good quality and the color code stayed the same. Had no problem what so ever and was an easy swap. I soldered every wires and protect them with heat shrink tubing and that should last a very long time. Thank you.
Very bad experience. Placed an order on 5-24-23 for an item that showed to be in stock on the website. Receive an email stating that is back ordered and due to ship 6-5-23, several emails later still no wiring harness. Finally 7-10-23 I receive an empty envelope, well not completely empty it has a letter from USPS stating that the enclosed was found loose in the mail. A box would have been more appropriate to ship this item, as I have been in shipping for two different companies for 38 years now. I am unable to upload pictures of the envelope, I will send them via email.
What our customers are saying:
"Very quick turn around time. Thanks."