Summer Starts Here - Save up to 70%
# 1
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Overall, I am extremely satisfied with the products I bought. Your communications are excellent; shipping was performed in an expedient manner and the tracking of the packages was much appreciated. I'm not sure I'll be buying anything else from you (I can't imagine needing another tow bar again) but will surely recommend your company if asked.
Fits loosely into the hitch, along with a loose fitting pin. Thus, your trailer will constantly rattle and clang every 10th of a mile that you drive. It will drive you crazy and insane thinking that your trailer with your $50,000 boat or camper will disconnect and be left along the highway behind you for all semi-trucks to run over and shred to thousands of bits and pieces.
# 2
Draw-Tite Drawbar for 1-1/4" Hitches - 5/8" Rise, 1-1/4" Drop - 7" Long - 3.5K
Looked everywhere for the right hitch tô fit my Ford Escape. Finally found it here. It fits perfect and delivery was fast. Will definitely be ordering from you again. Thank you.
With a receiver hitch already installed on a ford escape all my receivers are 2 inch but the one on the escape is 1 1/2 inch so I had a problem that etrailer had a solution for , the proper sized hitch that works great .
# 3
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 6-3/4" Long - 3,500 lbs
Perfect fit for a factory-installed classI II hitch on a 2010 Ford Escape.
no problem with this part.
# 4
Convert-A-Ball Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10,000 lbs
Makes for a great hard-core dirt road set up with a 3000 pound trailer, in conjunction with the Curt rocker ball, Towing with an F150 over many miles of washboards, down through washes where the road was washed out, etc. Really makes for a gentler set up on the equipment in the trailer and the truck. Thanks a lot E-trailer!
My usage of your hitch is a bit unusual, I think. I pull a two ton roller with my Ram and I've used your cushioned hitch to smooth out the process. The roller Lunette just dropped over a 2" ball and then banged and jerked on the ball neck. Check out the photos for my adaptation.. I can flip it over and use the 2" ball! Have enclosed some photos. The cushion is holding up very well and it takes a beating!! Thanks
# 5
Hidden Hitch Ball Mount - 3/4" Rise, 2" Drop - 15-3/4" Long - 6,000 lbs
Ordered this hitch and it worked perfect for what I needed just bought a teardrop trailer. Couldn't open up the tailgate on my Jeep so I ordered this extended hitch and I brought the ball out past my spare tire and the tailgate opens up now I have no problems. And I looked everywhere couldn't find one of this quality and at this price very reasonable the other ones hundreds of dollars didn't want to spend that much.
This is a huge difference maker for us. I can open the tailgate of our truck with the trailer still attached, and helps minimize any body damage if my backing up is not good.
# 6
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
Longer stinger let me drop the tailgate on my Tacoma with trailer attached. Replaced a similar but shorter Curt hitch and both are very substantial and well made for the weight of my trailer.
With good information from the website it was easy to order a Curt 2" Trailer Hitch, the Upgraded Circuit Protected Tail Light Converter Hardwire Kit w/ 4-Pole Connector and Circuit Tester - 119178KIT, Curt Ball Mount for 2" Hitches (3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs - D-4), Curt Pin and Clip Hitch Receiver - C21500, Rubber Tube Cover for 2" Trailer Hitch Receivers - I-728,Review, and 2" hitch ball 40038. Parts were delivered earlier than the initial estimate. Self installation (on a sloped drive way) took just under 2 hour. The fit of parts was very good, instructions and on-line video's were very helpful. My Kia did not have the wire plug in option, but the splice connections in the wire kit were easy to install. Most of the parts are hidden from view when the ball mount is not used.
# 7
Curt Towing Starter Kit for 1-1/4" Hitches - 2" Ball - 3/4" Rise - 3,500 lbs
No problem. Exactly what I needed
Looks great, if it holds up under use, then this is a great buy. Heavy duty, well spend money. I like the key lock, I have never seen this before but I can see you may have a need for locking your hitch at night in a motel parking lot or somewhere when you have to leave your hitch in your auto unattended.
# 8
Ball Mount 3/4" Rise or 2" Drop - 12-5/8" Long
Just what i wanted...
Great product! Easy install. Completed project myself in 1.5 hours...would recommend for any skill level...just gotta be willing to crawl around on your back
# 9
Reese Trailer Hitch Starter Ball Mount Kit
Feels strong .
# 10
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
Works great with my new Kurt receiver hitch and the drop is perfect for a level tow on a '08 Ford Escape.
Thrilled with the drawbar. Exactly the size we needed, well constructed, and fits with the Curt hitch and size requirements for hauling. Very pleased with how quickly it came.
# 11
Draw Tite Drawbar for 1-1/4" Hitch - 5/8" Rise, 1-1/4" Drop - 9-3/4" Long - 3.5K
Works perfectly. Needed a tow bar with very little rise and would clear the bumper. Thankfully, etrailer has a huge selection of equipment so you can find the right piece.
With a receiver hitch already installed on a ford escape all my receivers are 2 inch but the one on the escape is 1 1/2 inch so I had a problem that etrailer had a solution for , the proper sized hitch that works great .
What our customers are saying:
"The phone operator was very helpful and made my purchase easy. I will keep this website handy."