Upgrade the factory pin box on your fifth-wheel trailer to this cushioned model that dampens road shock and reduces back-and-forth chucking for a more relaxed towing experience. Unlike air bags, the internal rubber spring requires no maintenance.
Features:
Specs:
Most standard pin boxes are constructed of steel and are built with the sole purpose of connecting your fifth-wheel trailer to your tow vehicle. There is no cushioning built in, so a factory pin box doesn't do anything to provide a comfortable ride when you're hauling your fifth-wheel trailer.
This MORryde pin box, however, is built with an internal rubber spring that absorbs road shock and vibration at the connection point. So if you're driving on unpaved roads or uneven pavement, this pin box will prevent any road shock and vibration you encounter from transferring from your tow vehicle to your fifth-wheel trailer and vice versa. In other words, the rubber spring takes the brunt of the impact so you and your towing setup don't have to. And because this unit uses a rubber spring instead of an internal air bag like some other upgraded pin boxes, there's no maintenance required.
Although this pin box can tow up to 16,000 lbs, the internal rubber shear spring is optimized for trailers that are under 11,500 lbs. A rubber spring built for 16,000-lb trailers would be too stiff to provide any cushion for a trailer under 11,500 lbs, while a rubber spring built for trailers under 11,500 lbs would be too flexible for a 16,000-lb trailer.
Chucking, the back-and-forth jerking movement you feel in your cab when towing, occurs most frequently during starts and stops and while making turns. A typical, factory pin box creates a rigid connection without much give. So when a harsh stop occurs, all of the trailer's forward momentum gets forced through that stiff connection, slamming the king pin in the hitch and jerking your truck around.
To combat this, glide pads are built into the MORryde pin box that allow the skid plate to shift up to 3" forward and backward and 1-1/2" side to side to compensate for some of that violent motion so that you don't have to feel it in your cab.
This MORryde pin box is a direct replacement for your existing Dexter 2210031 pin box, so the installation is very straightforward. After removing your old pin box, the MORryde can be mounted into place using the same hardware and bolt holes used by the factory pin box.
Because of the weight of the unit, you'll want a couple of friends to help you lift it into place during installation. Once the hardware is securely bolted down, you'll be ready to go.
Alternate Instructions
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi there, I'm Michael with etrailer.com. Today we're going to take a quick look at this MORryde Cushioned 5th Wheel Pin Box. This cushioned pin box is going to replace the factory Dexter 2210031 pin box for your trailer. And it's going to ensure a nice, smooth towing experience, a much smoother than your current Dexter pin box allows. And that's because we have this rubber shear spring inside here, that's going to absorb and dampen your road shock and vibration, which will help reduce your back and forth chucking, while towing over uneven roads. It's going to make it a much more relaxed and comfortable ride when you're towing or hauling your trailer.
It's also going to help eliminate jerking when you're starting and stopping, which will limit the stress put on your trailer during your long road trips. This does also have the internal glide pads that allow the skid plate to shift forward and backward up to three inches and side to side up to an inch and a half which is going to allow for smoother maneuvering and help to reduce that chucking again. This is a bolt-on installation. It's going to require no drilling, it will fit right in place of your factory king pin, and it will use the same hardware and bolt holes as the factory pin box so it should be very easy to get installed. Of course it is very heavy so you will want a few sets of hands helping you lift or take down the old pin box and put this one up in its place.
But this isn't gonna require any maintenance. Unlike some of the other models of cushion pin boxes out there that use air bags. You're not gonna have to worry about putting air in, monitoring your air pressure with this system, because that has that rubber spring there. It's all gonna be very maintenance free, but you will wanna make sure that you're getting the right pin box for your trailer size. So there are three different sizes.
So if you have a trailer that's 11,500 pounds or less, you'll want that MR92VR part number. If you have a trailer that's 11,500 to 14,000 pounds, you'll wanna use that MR42XR, and if you are using a trailer that's 14,000 pounds to 16,000 pounds you'll want to use that MR62VR, just because the springs are designed to optimize different weights. So you wanna make sure that you're gonna get the spring that's gonna work best for you, it's not gonna be too soft or too firm for your application so make sure that you are getting the correct pin box there. This is made here in the USA so you can trust it's made to the high quality standards that we've come to know and trust for products that are made here in the US. So if you are wanting to replace your original Dexter pin box for a smoother ride, this is gonna be a great option for you.
That's gonna complete our look for today. Again, I'm Michael with etrailer.com. Thanks for watching.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.