Pollak 7-Way # PK11893-11932 Wiring Diagram

Question

Question:

I recently purchased this item from you. Watching the videos it mentions a picture on the product detail page showing the pin out for the bare wires. I dont see it on your page. Can you send to me please or link to it on your website? Thanks,

asked by: Rodney L

0

Expert Reply:

I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole # PK11893-11932 that you referenced.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector - Trailer End #PK12706 will match the colors and locations of the attached photo. I've also attached a wiring article to assist further if the colors don't match functions correctly…

view full answer...

Answer 2

There is no industry standard wiring code. Pollak uses the following: White - Ground Return Black - Clearance, Side Marker, Identification Yellow - Left Turn and Hazard Signal Red - Stop Lamps and Anti-Lock Devices Green - Right Turn and Hazard…

view full answer...

Answer 3

The easiest way to go from a 7-way round connector to a 7-way flat would be to get a Trailer Connector Adapter part #HM47425. However, if you are looking for a more permanent solution you would need to remove your 7-way round connector and wire up…

view full answer...

Answer 4

The 12 volt power wire in the Pollak 5th Wheel / Gooseneck T-Connector #PK11893-11932 is 10 gauge. The ground is 8 gauge. The Brake output wire is 10 gauge. All others are 12 gauge.

view full answer...

Answer 5

The black wire of the #PK11893-11932 does carry the 12 volt power circuit. This circuit is a 12 gauge wire. The standard amperage rating for 12 gauge wire is 41 amps typically, but this harness has a 30 amp rating. I attached a diagram that has a…

view full answer...

Answer 6

When wiring a 7-Way on your trailer with 5 wires, your green wire will be right turn/brake, the yellow wire will be left turn/brake, the brown wire will be the taillights, and the white wire will be the ground. You will want to find out if the blue…

view full answer...

Answer 7

We only had the black #LH94VR you found before so I went ahead and had it added to our site. The replacement wheel you are looking for is the Aluminum Margay Trailer Wheel - 15" x 5" Rim - 5 on 4-1/2 - Gunmetal Gray #LH69VR.

view full answer...

Answer 8

Given that trailer wiring only consists of basic light functions, 12 volt power, and brake output a system of fuses is not necessary because it is easy to determine if something is not working. If there was a short, the way you would know with or…

view full answer...

Answer 9

On the back of the Pollak 7-Pole, Round Pin Trailer Wiring Socket - Vehicle End, part #PK11720, it is marked alongside the pin with the color of the wire that connects to that pin location. I am also including a photo that will show a 7-Way round pin…

view full answer...

Answer 10

I wish we had replacement parts that would work for your trailer, but the best solution we have would be to replace the coupler since we do not carry the repair kit you need. For a similar hand wheel style coupler we have the part #T2343400.

view full answer...

Answer 11

Yes, the 7-Pin Round connector is wired differently than the 7-Way flat RV connector. I will list the typical heavy duty truck wiring connections inside the plug on the trailer side for you. At the index guide for plugging the trailer end in to the…

view full answer...

Answer 12

I have attached a photo of the Pollak Heavy-Duty, 7-Pole #PK11700 as viewed from the front with all of the correct wiring connections noted. 12:00 - White Wire is Ground. 2:00 - Brown Wire - Tail and Running Lights. 4:00 - Green Wire - Right Brake…

view full answer...

Pollak 7-Way # PK11893-11932 Wiring Diagram

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching