T-Slot Parts for Mounting Thule Hullavator Pro on Thule WingBar Evo Crossbars

Question

Question:

I just bought the Hullavator that came with 2 t bars only. This is the 898 Pro. I need to know what do I need to mount onto THULE WingEdge Evo bars. T brackets x 2, nuts x 2 and bolts x 2?

asked by: Michael A

0

Expert Reply:

Hey Michael, thanks for reaching out!

In order to install the Thule Hullavator Pro Kayak Roof Rack # TH898 into the WingBar Evo T-Slots you'll need the following parts:

- Replacement Square Nut # 853-7557 (qty 4)
- Replacement M6 x 37 mm Screw # TH97FQ (comes with qty 4)

Attached is a clip from the instructions for you to check out. Let me know if you have any other questions!

expert reply by: Jon G

0

Answer 1

To get replacement T-Slot hardware for your older model 897XT Thule Hullavator carriers you need the following parts (4 per Hullavator system): - Square Nut #853-7557 - M6 x 30 Socket Head Cap Screw #TH919063054 - M6 Washer #951061254 I've…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The replacement bar mount assembly just includes the bar mount, you'd still need the mounting hardware, so you will need 8 of the Replacement Socket Head Cap Screw for Thule Fit Kits and Ski Carriers #TH919063054 and 8 of the Replacement Square…

view full answer...

Answer 4

Hey Bruce, we have the Draw Tite hitch part #DT27YR that fits your 2025 Hyundai Ioniq 5 which I attached a picture from the install instructions that covers where to trim. Since the back of the vehicle is all covered up there's no real way to…

view full answer...

Answer 5

From my understanding you should just need the M6 x 30 Socket Head Cap Screw #TH919063054, the M6 Washer #951061254, and the Square Nut #853-7557 for installing the older Hullavator into the T-Slot of a crossbar system. This stuff should have come…

view full answer...

Answer 6

I pulled a Replacement Square Nut #853-7557 from our warehouse and found that its dimensions were .79 by .79 of an inch and .17 of an inch thick. Check out the video I took that shows these dimensions.

view full answer...

Answer 7

The Yakima HD Crossbars #Y01156 will work with the Thule Hullavator #TH898. Based on the pictures you sent in it looks like you have the crossbars installed upside down. The end caps have an opening on the other side that lets you easily slide in…

view full answer...

Answer 8

Yes, the older Thule Hullavator (897XT) will fit Yakima JetStream bars. You'll use the T-Slot mounting hardware that would have come with the older model carrier and then you need to make sure you can move the carrier out far enough that there is…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 11

Hey Ken! The 50" aero bars are definitely going to be too short. Each Thule Hullavator item #TH898 requires 28-1/2" of crossbar space, so with two of them you will need at least 57" crossbars. This means you'll have to install the…

view full answer...

T-Slot Parts for Mounting Thule Hullavator Pro on Thule WingBar Evo Crossbars

Product Page this Question was Asked From

Continue Researching