What Bearing Kit Will Work With A 3,500 lb Terran Axle?

Question

Question:

Will this kit work with a 3500 lb Terran Axle? That is what i have on my Forest River 26DBH.

asked by: Daniel H

0

Expert Reply:

Hello Daniel, thanks for reaching out. The Timken Bearing Kit # TMK52VR uses the standard 3,500 lb bearing sizes so it SHOULD fit your 3.5K Terran axle. The only way to absolutely confirm this will be to pull a hub and check/measure the bearings. The Terran brand axles are not common, so we do not have any specific info on their bearing sizing. As long as the axle was made within the last 20 years or so it should use the same standard bearing sizes, but please do confirm this.

expert reply by: Jesse M

0

Answer 1

Hey Scott, thanks for reaching out! The Timken Bearing Kit #TMK92VR you're looking at is for a 7K axle, and according to my research your 2021 Jayco Jay Flight SLX 195RB should be equipped with a 3.5K axle so we need to get you a different kit.…

view full answer...

Answer 2

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 3

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 4

Hi Tony; the #BK2-100 and #TMK52VR come with the same size bearings and grease seal. The main difference is the Timken name. This is usually associated with a higher quality bearings that are made in the USA which also accounts for the higher cost.

view full answer...

Answer 5

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 6

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The ALKO 4,400 lb axles use the same bearing sizes as the standard 3,500 lb alxes. If you want USA made bearings, I recommend the Bearing Kit #TMK52VR. This kit comes with the Timken brand bearings which are all made here in the USA.

view full answer...

Answer 9

Hey Barry, sure do! The seal that comes with the #DX87UR bearing kit is a 1.719" ID and 2.565" OD. We offer this seal individually as part #58846.

view full answer...

Answer 10

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 11

Hey Mark, the oscillating vent of the Furrion Chill Cube #FR27TD points to the front. Is there anyway you could use it pointing forward?

view full answer...

What Bearing Kit Will Work With A 3,500 lb Terran Axle?

Product Page this Question was Asked From

Continue Researching