Is Calcium Sulfonate Complex Grease Compatible w/ Lithium Grease?

Question

Question:

I bought pb blaster calcuim sulfonate complex grease by mistake to use on my dexter ez lube axles is says its compatible with lithuim greases and is extra tacky, extreme pressure, water resistant, high temp will this grease be ok to use ?

asked by: Joe

0

Expert Reply:

You're good Joe! Calcium sulfonate complex grease is compatible with the lithium grease like item # L11390, that Dexter uses.

expert reply by: Jerred H

0

Answer 1

Standard tapered trailer wheel bearings are recommended to be re-packed with fresh bearing grease about every year or every 12,000 miles under normal use. In certain conditions this interval could be shorter, such as if you routinely tow the trailer…

view full answer...

Answer 2

Hey Doug, That's a good question because fit is really important so the cover stays snug on your trailer, and there is a specific way to measure for the etrailer covers. It's pretty simple, and what you want to do is measure the body of the…

view full answer...

Answer 3

Unless you want to completely clean out every bit of grease you will need to stick to a LMX red grease like item #L11390 that comes with the CE Smith Trailer Idler Hub Assembly item #CE13515. You can use your blue marine grease but you can't mix…

view full answer...

Answer 4

I recommend the LubriMatic LMX Industrial Strength Grease #L11390 for your Dexter axle on your 2021 Vista Cruiser Travel Trailer. This grease is specifically formulated to work in extreme hot and cold temperatures under high pressures. It is also…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

In order to verify the spindle dimensions so that you can pick out the correct hub/drum you have to get exact dimensions. For that you need to use a digital caliper like part #PTW80157. For how old your trailer is this is especially important as the…

view full answer...

Answer 9

We recommended to repack the wheel bearings on your trailer every 12 months or 12,000 miles. There is not a specific guideline as far as actually replacing the bearings. When repacking them with grease, you will also just want to check for any damage…

view full answer...

Answer 10

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 11

You are going to want either our Bearing Kit #BK2-100 or the Timken Kit #TMK52VR. Both of these kits will give you the inner/outer bearings and races along with a grease seal and cotter pin/D-washer for one hub. You always want to replace the race…

view full answer...

Answer 12

Hey Chris! We don't have the O-rings individually but we do have the Kodiak XL ProLube Oil Bath Hub Body and Cap - 1.98" #xlprolube1980. These are the same caps that came with your disc brakes. If you need anything else feel free to reach…

view full answer...

Is Calcium Sulfonate Complex Grease Compatible w/ Lithium Grease?

Product Page this Question was Asked From

Continue Researching