Heavy Duty 2-5/16" Bolt On Trailer Coupler Made In The USA

Question

Question:

Im looking for a 2 5/16 trailer coupler heavy duty bolt on. That is made in USA, do you have any?

asked by: Chad W

0

Expert Reply:

We have the Demco Channel Tongue Trailer Coupler # DM16080-52 for a straight tongue and the Demco 50-Degree A-Frame Trailer Coupler # DM16680-52 for A-Frame. Both are made in the USA, are bolt on and rated for up to 21,000lbs. Both come with the eZ-Latch coupler to make connecting to your trailer easier.

expert reply by: Bud M

0

Answer 1

The HydraStar Marine Electric Over Hydraulic Actuator w/ Breakaway and 7-Way RV Harness #HS381-9067 is designed to work with an aftermarket electric over hydraulic brake controller. This kit will require you to wire in the components using the wire…

view full answer...

Answer 2

The Hydrastar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes #HS481-8067 is designed to be completely plug-and-play so the female end of the 7-way would need to connect to the 7-way cable that's already installed on the trailer…

view full answer...

Answer 3

I attached a link to an installation video for the #HBA-CAM you can check out. At About the 6:25 mark on the video, the electrical connection is shown. As long as you have a solid connection between the Actuator and the #HBA-CAM, it would work.

view full answer...

Answer 4

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 5

Hello Ziggy, Good question. The DeeMaxx Alpha G1600 Plug and Play Electric Over Hydraulic Actuator #DE75KR works with 2017–2022 GM trucks that have built-in brake controllers, like the Silverado and Sierra. It’s built to “trick” the truck into…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

First you will need to remove the old hydraulic equipment. Remove the surge coupler or actuator, remove all the lines, and finally remove the brake assemblies. If you have 10 inch diameter hub and drums, you may need to replace those as well. If you…

view full answer...

Answer 10

Hello Bob, I’m sorry, but we do not offer kits with 5/8" studs. That said, the Hydrastar actuator paired with the Kodiak brakes is a great setup! The only thing I would recommend changing is the brake lines, here’s the combination I would…

view full answer...

Answer 11

It sounds like you need the Hydrastar Electric Over Hydraulic Actuator Adapter Module #HBA-CAM for the OEM brake controller on your 2022 Ram 3500. This will ensure that your controller works properly with the Hydrastar Electric Over Hydraulic…

view full answer...

Answer 12

Hey Kevin, the DeeMaxx Alpha G1600 Electric Over Hydraulic Actuator for Disc Brakes - Plug and Play Kit #DE75KR that you referenced is a solid option and does not require an additional control box to operate unless you would be referring to a brake…

view full answer...

Heavy Duty 2-5/16" Bolt On Trailer Coupler Made In The USA

Product Page this Question was Asked From

Continue Researching