Puck Light Replacement for RV Ceiling that is 3-3/4 inches Diameter

Question

Question:

I am looking for puck lights that are 3.75inch on the front and 2.75inch on the back. There are 2 wires on the back and there are two clamps that hold it to the roof.

asked by: Mike

0

Expert Reply:

In the spring mount style of puck light the closest option we have is the part # DG52445VP that you referenced but would require you to slightly open up the holes in your ceiling if what you have is 2-3/4 inches in diameter as this needs a 3 inch hole.

expert reply by: Jameson C

0

click to enlarge

Answer 1

What you have appears to be a standard puck light which you could use the part #277-000343 as a replacement for if it's 3 inch in diameter like it looks like. We also have 4-1/2 inch size like part #277-000344 but it does look to me like you have…

view full answer...

Answer 2

Since your existing cut out is 3 inches in diameter you can absolutely use the 12V RV LED Puck Light #DG52445VP. While the #DG52445VP has an overall diameter of 3-1/8 inches, the cut out size needed is just 3 inches, as any hole larger than that…

view full answer...

Answer 3

The gear that you're talking about on your MaxxFan 4401K is the operator mechanism. For a replacement you need the #MA10-20281K-1AF.

view full answer...

Answer 4

For a front hitch for your 2023 Ford F-350 dually I recommend the Draw-Tite #65076. This is going to be the only front hitch we offer that will fit the DRW models. This has a 2" receiver and a 500 lb vertical load limit. As far as installation,…

view full answer...

Answer 5

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The RV Propane Gas Detector part #RS64FR is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you had for the previous so it will be a…

view full answer...

Answer 11

Hi Brenda, The Atwood 31013 unfortunately has been discontinued so you'd need to go with a completely new LP gas detector. We have a couple of surface mount style detectors that come with trim rings that will cover the old unit's cutout hole…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Puck Light Replacement for RV Ceiling that is 3-3/4 inches Diameter

Product Page this Question was Asked From

Continue Researching