Are E-Z Lube Grease Zerks Threaded or Pressed In
Published 07/19/2020
Question:
I need to replace a zerk fittings on my easy lube tracker boat trailer spindle. What grease fitting does it use and where can I buy it. Is it screwed in or pressed it?
asked by: Al
1
Helpful Expert Reply:
The E-Z Lube grease zerks are threaded in, and if you can remove your zerk with the threads not damaged, people have had success replacing it with the Replacement Grease Zerk # Gzerk.
The zerks have a standard 1/4" pipe thread fitting which is what this zerk has.
expert reply by:
Kyle S
1
Product Page this Question was Asked From
Replacement Grease Zerk for Ram Jacks
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Grease Zerk
- etrailer
more information >
Continue Researching
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Q&A: Zerk Fittings Keep Falling Out on Boat Trailer With EZ-Lube Spindles
- Q&A: Why Are The Erickson Ratchet Straps EM98CV Falling Off My Tires
- Search Results: torsion axles
- Search Results: rv waste valves
- Search Results: dry lube
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Search Results: grease zerk
- Search Results: dc to dc charger
- Search Results: bearing l44649 and l68149 trailer bearings races seals caps
- Search Results: grease fittings
- Video: Review of Dexter Axle Grease Zerks EZ Lube Spindle - DX76HR
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Video: Review of Vitrifrigo RV Refrigerators - Stainless Steel RV Refrigerator With Freezer - VT96FR
- Shop: Dexter Grease Zerks for E-Z Lube and Nev-R-Lube Axles - Press-In - 1/4" OD x 5/16" Long
- Video: Genesis Revive RV Wall Coverings – At a Glance
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Curt Soft Trac II Trailer Breakaway Kit with 5 Ah Battery and Clamp On Case - Top Load
- Shop: Erickson ATV E Track Tie-Down Kit w/ Ratchet Straps and Wheel Chocks - 1,500 lbs - 4 Wheel Set
- Video: Review of Valterra RV Waste Valves - Electric Straight Waste Valve - VAL23MB
- Video: All About the Master Lock Pivot Lock Hitch Pin for 2" Hitches
- Video: Feature Breakdown: Seal Puller
- Q&A: Retaining Nut For Dexter Hub & Drum 5,200 lb - 6,000 lb Part 8-201-9UC3-EZ
- Q&A: Replacing The Zerk Fitting On A Dexter EZ-Lube Trailer Axle
- Q&A: Solution for Zerk Fitting of EZ Lube Spindle Wearing Out Rubber Cover
- Video: Trailer Axle with Idler Hubs Spec Review
- Q&A: Timken Bearing Kit Fitment for a 3,500 lb Axle
Al
7/19/2020
I need to replace a zerk fittings on my easy lube tracker boat trailer spindle. What grease fitting does it use and where can I buy it. Is it screwed in or pressed it?