Brake Controller Port Location for Tekonsha Prodigy P3 On a 2020 Ram 1500
Products Featured in This Question
Question:
After reading QandA on your website I settled on using the Prodigy3 with the 3024-P harness for my 2020 Ram 1500. I have looked at your site and the 2019 dash is different than the 2020. The picture you showed of the 2019 allows access to the area to reach the factory plug. The 2020 is closed of at the bottom of this area with a storage bin. I know Dodge is calling the 2020 redesigned does anyone know where the factory connector is located on the 2020 Ram 1500?
asked by: Mike L
Helpful Expert Reply:
The Tekonsha Prodigy P3 Trailer Brake Controller part # 90195 with the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 3024-P is indeed a good choice for a 2020 Ram 1500. In regards to installation, the plug is located behind the center dash console near the gear selector where the factory brake controller would have been installed if equipped. The attached photo shows a general location but as noted, there are different dash configurations for the vehicle so exact panels/compartments can vary by model. That said, the attached photo of a 2019 is on the new generation so the same will apply to the 2020 but as stated there are different dash configurations.

Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Splice-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- LCD Display
- Multiple Trailers
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Video: Electric Over Hydraulic Disc Brake Installation - 2021 Vanleigh Beacon Fifth Wheel
- Search Results: kodiak 225 caliper
- Shop: Hydrastar Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi
- Q&A: How to Determine Correct Replacement Ceramic Kodiak Brake Pads
- Q&A: How to Determine Which Brake Pads Work on my Trailer?
- Q&A: Can I Use the Kodiak Rotor KR12D to Replace a Tie Down Engineering TDE46247 Rotor
- Search Results: hs496~252
- Shop: Kodiak Disc Brake Caliper - Dacromet - 3,500 lbs to 6,000 lbs
- Shop: Kodiak Ceramic Brake Pads - 3,500 lbs to 6,000 lbs
- Shop: Kodiak 12" Rotor - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs
- Shop: Kodiak Disc Brake Caliper Rebuild Kit for 3,500 lb to 6,000 lb Trailer Brakes
- Shop: Hydrastar Hydraulic Brake Line Kit - Tandem Axle - 25' Long, 3/16" Main Line
- Shop: Kodiak Disc Brake Caliper - Dacromet - 7,000 lbs to 8,000 lbs
- Video: All You Need to Know About the Hydrastar Electric Over Hydraulic Actuator for Disc Brakes
- Shop: Brake Controller
- Search Results: hba16
- Search Results: brake actuator
- Search Results: 2~5/16 coupler
- Video: In-Depth Review of the Buyers Products Straight Tongue Trailer Coupler
- Video: HydraStar Marine Electric Over Hydraulic Actuator Installation
- Q&A: Parts Needed for Converting Trailer to EOH Disc Brake Operation
- Video: An In-Depth Look at the Wiring Kit for Hydrastar Electric Over Hydraulic Actuators
- Q&A: Will Redarc Tow-Pro Brake Controller Install Require a 2023 Ram 1500 Classic to be Reprogrammed?
- Q&A: Is Redarc Tow-Pro Elite Brake Controller Compatible with Hydrastar Electric Over Hydraulic Actuator
- Q&A: Ram OEM Brake Controller Issues With Hydrastar Electric Over Hydraulic Trailer Brakes
- Search Results: 3x4 trailer tongue
- Search Results: 2 5/16 coupler
- Video: HydraStar Electric Over Hydraulic Disc Brake Actuator Installation - 2017 Keystone Montana Fifth Whe
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
Angel
7/7/2020
Do anybody PLEASE know where is the factory brake controller port FUSE for the 2019 1500? Last year I installed the Tekonsha Prodigy P3 Trailer Brake Controller using their harness and it was working perfectly fine but the past weekend I noticed the brake controller was not powering on and of course no brakes on the trailer. Today, Iv'e been checking all kind of fuses first, including every single one the owners manual refers as "towing" and no luck. I tested the brake controller directly to power and powers on normally, so is not the break controller. I went under the dash where the factory brake controller port is located and everything looks normal. I have tested and I get 12v from the red cable when I press the brake pedal (good) and i checked ground continuity from the harness to the chassis and ground is fine, the only that is NOT showing power is the positive cable (thick white with a red trip) that comes from the factory controller port to the Prodigy harness, so, it got to be a FUSE because i really doubt a positive cable just got unplugged from wherever is coming (I cant reach farther in the dash) Unfortunately an extensive internet search is not giving me any "Brake Controller Port FUSE" I hate so much go to the dealer that I even prefer to run a positive cable from the battery if I cant get this sorted out but I will prefer leave the clean installation and figure this out. I will appreciate any help.