What Are the Brake Controller Wire Colors for on a 1998 Dodge Ram 2500
Updated 04/15/2025 | Published 05/28/2019
Products Featured in This Question
Question:
I have been chasing this problem for months. When I put my foot on the brake pedal the control module flash 10, 20 and then stop it will not set the brakes on the trailer. I have worked on it myself by switching out controllers changing the brake actuator that sends the signal to the controller and even putting in another controller after that. What I have finally figured out is that the four wires coming out of the firewall of my Dodge a red, black and orange, red and brown and a blue wire red being hot Blue being brakes white and brown and black and orange I do not know but I do know that out of those four wires the blue the white and brown and the black and orange are grounded. I tested this by a multimeter putting one end on the ground and turning the multimeter on to ringing or continuity and touching the terminals. How do I fix this and is there a wiring diagram where I can chase these wires to see where theyre grounded at?
asked by: Josh
Expert Reply:
The factory electric trailer brake controller wires on a 1998 Dodge Ram 2500 are as follows:
Power - Red/Orange
Ground - Black/Orange
Stop Light - White/Tan
Brake Output - Light Blue
For a brake controller, I recommend using the Tekonsha Voyager Trailer Brake Controller part # 39510. It sounds like the previous owner of your truck may have cut off the old brake controller port so you are also going to want to use the Replacement Brake Control Plug-In Harness for Tekonsha and Draw-Tite Brake Controller part # 20127. The above wires will then need to be attached to the brake controller as follows.
Red/Orange - Black
Black/Orange - White
White/Tan - Red
Light Blue - Blue
If the brake controller still does not function correctly once the following connections have been made you will just need to splice into these circuits yourself with new wires from the back of the brake controller.
Product Page this Question was Asked From
Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Splice-In
- Under-Dash Box
- Under-Dash
- Up to 4 Axles
- Indicator Lights
- Single Trailer Only
- Tekonsha
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Brake Controller
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V XD - 2"
- Shop: B&W Heavy-Duty Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Q&A: What is the Difference Between the Tekonsha Prodigy P2 and the P3 Brake Controllers
- Shop: Tekonsha Custom Wiring Adapter for Trailer Brake Controllers - Dual Plug In
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller w/ Custom Harness - Up to 4 Axles - Proportional
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller w/ Custom Harness - Up to 4 Axles - Proportional
- Q&A: What Amperage Circuit Breaker Should be Used for Brake Controller Install
- Q&A: How Does a Brake Controller Know when a Trailer is Connected
- Q&A: Troubleshooting a Tekonsha P3 Brake Controller With Trailer Brakes That are not Showing Power
- Q&A: Brake Controller Shows Trailer Connected with No Trailer Connected
- Q&A: How to Add Second 7-Way to Truck For Bumper Pull Towing and Gooseneck/5th Wheel Towing
- Video: Ultimate Overview of the Incandescent RV Tail Light
- Search Results: floor register
- Search Results: rv stove vent
- Q&A: Where Does Blue Wire of 7-Way Run to Power Trailer Brakes
Zack
4/15/2025
On a 99 2500 Dodge ram sport model 5.9 gas motor electronic brake controller wiring color. I have an aftermarket one that is red white blue and black what the factory plug is red and orange blue white and red and then black and orange I’m just trying to figure out what wires to plug into that How they go.