How to Install the Pack'Em Rack Part # PK-6-OP1 on a Utility Trailer with Wooden Side Walls

Question

Question:

Would I be able to install this on the back of my trailer?

asked by: Tameron

0

Expert Reply:

In order to install the Pack'Em Rack for Open Utility Trailers part # PK-6-OP1 on your utility trailer, I recommend attaching the uprights to the wooden sidewalls of the trailer or trimming the wooden side walls to allow the uprights to sit flush on the frame. I have attached a customer submitted photo of this for you to give you a better idea. The rear liftgate that you are referring to would not be a suitable place to mount this rack.

expert reply by: Conner L

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Stanley! To clear things up, you need to connect the white plug. However, this is definitely confusing. I just looked at the #FR27TD instructions and I see where it says to tuck the white connection off to the side, unused. Directly below that it…

view full answer...

Answer 4

Hey Mark, the oscillating vent of the Furrion Chill Cube #FR27TD points to the front. Is there anyway you could use it pointing forward?

view full answer...

Answer 5

Hello John, No, the Optronics Thinline LED Trailer Fender Light for Trailers Over 80" Wide - 10 Diodes - Amber/Red #MCL65ARB will not have the etrailer logo on it like you see in the picture. Our photo team only puts the sticker on there when…

view full answer...

Answer 6

I would be happy to help! For your 2021 Toyota Highlander there are quite a few different options but it will be dependent on if your vehicle is an XSE model or not. The EcoHitch #EH35VR, and etrailer #e75ZR will fit ALL models of the 2021 Toyota…

view full answer...

Answer 7

No, Thomas it does not have any weight limitations. The etrailer Anti-Rattle Hitch Collar for 2" Hitch Receivers item #e38FV attaches directly to the lip of your vehicle's hitch. Doing so allows it to limit the movement of the ball mount or…

view full answer...

Answer 8

The only hitch that is compatible with the full size 20" spare tire on a 2023 Toyota Highlander is the EcoHitch Hidden Trailer Hitch item #EH35VR. This hitch is custom fit and bolts to your Highlander with included hardware. This is a class III…

view full answer...

Answer 9

I recommend the Curt Echo Wireless Trailer Brake Controller - 1 to 2 Axles - Proportional Item #C51180. If the dealership is installing the 7 pole connector, this controller doesn't require any additional wires to be ran inside the vehicle. Your…

view full answer...

Answer 10

We do not sell a complete kit but we do sell a backing plate that is compatible with the Square D-Ring Tie-Down Anchor item #ABS69FR. It is the Backing Plate for Brophy Recessed D-Ring Tie-Down Anchor item #BP05.

view full answer...

Answer 11

Hey Jack, If you're talking about a transition plate then you'll want the etrailer Enclosed Trailer Transition Plate #e32JR. This can be installed on either end of the ramp to help make the transition onto easier or at the hinge of the ramp…

view full answer...

How to Install the Pack'Em Rack Part # PK-6-OP1 on a Utility Trailer with Wooden Side Walls

Product Page this Question was Asked From

Continue Researching