Trailer Fender Recommendation for a 1999 Bayliner Capri Single Axle Trailer with 15 Inch Wheels

Question

Question:

I would like to know if this will fit my trailer I currently have a 1999 Bayliner Capri trailer single wheel axle with 15 tires wondering if this is a good substitute. Thanks for the help

asked by: Josh S

0

Expert Reply:

The Fulton Plastic Fender, # F008585-2, is designed to fit on single axle trailers with 15 inch wheels, so it would be a good fit for you. To make sure the fender is the right size for your needs, take a look at the dimensions on the product page below the description to ensure proper fit.

If you find you need something different, I have included a link to our fenders for 15 inch wheels for you.

expert reply by: Michael H

0

Gerry C.

7/8/2020

I need two fenders for a 2000 Capri trailer, single axle with 13" wheels. Overall length 42.5" +/-

Reply

Chris R.

7/13/2020

I went ahead and linked our full selection of trailer fenders for 13" wheels below. In the length you're looking for the CE Smith # CE19503-2 should work nicely. These black fenders have a total length of 40-1/8".

Helpful Links

dept-pg-trailer_fenders-pt-13_inch_wheels.aspx

Reply

Glen

5/14/2024

Looking for 2 fenders for 15 inch wheels 3 stepping places each side and top

Reply

Kevin C.

5/24/2024

@Glen If you have a single axle trailer then you can go with the Fulton Single Axle Trailer Fender with Top and Side Steps # F008575. These come with top and side steps and fit 15" wheels.

Reply

Answer 1

Thank you for the photos! According to my information and what you sent in, your best option for a replacement fender is the CE Smith Black Fender: CE Smith Single Axle Trailer Fender w/ Top and Side Steps - #CE19503 (Qty 1) CE Smith Single Axle…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 6

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 7

The only difference between 7-Way Utility and 7-Way RV is the color of the wires. The pin outs are the exact same so either would work just fine with the other. If you check out the picture I attached you'll see that the functions are all the…

view full answer...

Trailer Fender Recommendation for a 1999 Bayliner Capri Single Axle Trailer with 15 Inch Wheels

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching