How to Determine Bolt Pattern of 5 Lug Trailer Wheel

Question

Question:

Currently have ST205/75/R14 - 5 lug tires on my 2014 Keystone Bullet. Is that the same as 5 on 4-1/2inch bolt pattern?

asked by: JWalker

0

Expert Reply:

The 5 on 4-1/2 inch bolt pattern is the most popular 5 bolt lug pattern found on trailer wheels. There's an easy way to measure and be sure though. You need to measure from the center of one lug to the center of the lug nearest to it.

If the distance is:
2-5/8" - the bolt pattern is 5 on 4-1/2
2-3/4" - the bolt pattern is 5 on 4-3/4
3" - the bolt pattern is 5 on 5
3-1/4" - the bolt pattern is 5 on 5-1/2

The part # TTWA14RWS you referenced has a 5 on 4-1/2 inch bolt pattern.

expert reply by: Jameson C

0

Scott K.

9/7/2020

Does anyone know what the bolt pattern is on 2002 Coachmen Lite 28BH 5th wheel? It’s 6 lug.

Reply

Jon G.

9/10/2020

It's probably 6 on 5-1/2" as that's really the only 6 lug bolt pattern that's common for trailer tires. Here is a link to our selection of tire/wheel combos that use the 6 on 5-1/2" bolt pattern for you to check out. Just make sure that you have the same size and load range that you currently have on your 5th wheel.

Helpful Links

dept-pg-trailer_tires_and_wheels-sz-6_on_5~1%7c2_inch.aspx

Reply

Shane

3/16/2024

My trailer rims are 3 1/2 inches bolts difference what type of rim is this the standard trailer rims I ordered don’t fit they are 31/4 ?

Reply

Jameson C.

3/25/2024

@Shane That is an odd bolt pattern that isn't something we carry unless the measurement was possibly taken wrong, did you measure from bolt center to bolt center? It should be center to center.

Reply

Answer 1

The Dexter Axle Torflex axles are basically broken up into the following categories: #9 - 1,000 - 2,200 lb #10 - 2,300 - 4,000 lb #11 - 4,100 - 6,000 lb #12 - 5,500 - 7,200 lb Based off of your 2004 R-Vision Trail-Lite Model 8306S being a tandem axle…

view full answer...

Answer 2

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 3

Measuring the inside diameter of the hub where the cap press fits into it is the best bet to get the right replacement grease caps. If you have access to a dial caliper, that would make the job that much easier. Measuring with a tape measure is…

view full answer...

Answer 4

You won't need a new harness. The Tekonsha Prodigy P3 item #90195 does indeed use the exact same harness as the Tekonsha P2 item #90885.

view full answer...

Answer 5

On a 2006 Jeep Liberty installing a brake controller requires that it be hardwired to the vehicle. hardwiring is not vehicle specific so you can follow along with any video showing installation using a 4 and 7 way installation kit #ETBC7. I have…

view full answer...

Answer 6

The fuse you found in the engine compartment is used to protect the 12-volt accessory power feed to the trailer connector. Since your Liberty was not equipped with the factory installed 7-way, this circuit is inactive. Some Jeep Liberty models that…

view full answer...

Answer 7

The 5 on 4 3/4 bolt pattern is starting to get less and less common, so they are getting a little difficult to find. With that being said, this bolt pattern was generally not used on wheels of this size in the trailer world. If you take a look at the…

view full answer...

Answer 8

There really should be a flat washer between the outer bearing of your hub and the nut that holds it on. The washer protects the back side of the bearing from the edges and points on the back side of the spindle nut. The Washer For 1 inch Spindle,…

view full answer...

Answer 9

I have a solution for you, but the part #AKIHUB-545-35-K does not come with marine grade grease. Instead you would want the part #CE13511 as it is essentially the same spec hub in terms of bolt pattern and what spindle it fits except it does come…

view full answer...

Answer 10

Wheel bolt patterns are defined by two numbers: the first being the number of lug nuts and the second being the diameter of the circle the lug nuts are arranged in. So a 5 on 4-1/2 bolt pattern is 5 lugs arranged in a circle that is 4-1/2 inches in…

view full answer...

Answer 11

The big differences between a Class IV and a Class V hitch are the capacities and the opening size. Class IV is going to be a 2 inch hitch opening that has tongue weights typically up to 1,200 lbs and total trailer weight of 12,000 lbs. For a Class V…

view full answer...

Answer 12

For saltwater boat trailer use it is recommended to go with either a galvanized steel rim or a aluminum wheel. For a galvanized option I recommend the Americana Steel Spoke Trailer Wheel part #AM20354. Both these rims have excellent corrosion…

view full answer...

How to Determine Bolt Pattern of 5 Lug Trailer Wheel

Featured Help Information

Miscellaneous Media

Continue Researching