Can Weight Distribution System and Timbren Suspension Enhancement Work Together on 2012 Ram 2500

Question

Question:

I have a 2012 Ram 2500 4WD and we just bought a travel trailer. Ive been looking into the various types of weight distribution hitches to have a better towing experience. Ive never used one before but I do understand how it works. I also use my truck to haul wood for firewood and the loads arent extreme but are heavy at times, for this Ive been looking at the Timbren SES to help with reducing sag and overall ride quality. Heres my question, are there any advantages or disadvantages if I install the timbren ses and use it with a E2 style weight distribution hitch when towing my travel trailer.

asked by: Bradley B

1

Helpful Expert Reply:

The Timbren Rear Suspension Enhancement System # TDR2500CA that fits your 2012 Ram 2500 and a weight distribution system, the Fastway e2 Weight Distribution # FA92-00-1000, provide different benefits to your truck, and using both is a good idea based on how you described using your Ram.

Since you use your truck to haul loads and not just tow, the Timbrens are going to offer your Ram's suspension the necessary support compared to hauling those loads without the Timbren's. When towing your travel trailer, the Timbrens are not going to offer as much benefit if your weight distribution is properly set up; that said there isn't any disadvantage to having suspension enhancement and weight distribution (in fact, the combination can only be helpful). The Fastway is going to transfer the weight of the trailer and distribution it across the axles to even out your ride when towing, which is something the Timbrens can't do.

I have added links to video reviews of the Timbren Rear Suspension Enhancement System # TDR2500CA as well as the Fastway e2 Weight Distribution # FA92-00-1000 for you to check out.

expert reply by: Kyle S

1

Answer 1

I have the perfect option for a Ram 2500/3500 which is to use the Aries Bull Bar with Removable Skid Plate part #AA35-5006 with the Tow Hooks for Aries 3" and 4" Bull Bars part #AA35-5TOW. The bull bars do require the factory tow hooks to…

view full answer...

Answer 2

The use of rear suspension enhancement along with a weight distribution kit is not recommended. They will tend to work against one another. If sag on your 2008 Ford F-150 is caused by a load or a fifth wheel or gooseneck trailer then suspension…

view full answer...

Answer 3

You won't have any issues with this setup. The payload capacity of the truck refers to the capacity of the aluminum truck bed where the pin-weight capacity refers to the amount of additional weight the axles and frame can support. With the hitch…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

The Reese Titan Extension/Reducer you referenced, part #RP45292 would work great with the 2-1/2 inch Class V hitch on your Ram. As you mentioned, the extension has a 8K capacity when cut down to the 24 inch length, that will provide a 2 inch receiver…

view full answer...

Answer 10

We have a full replacement for your light. The Command Electronics #CE86FR. Take a look at the attached video to see them in action.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...